Nissan Navara D23 EGR Cooler Replacement (NP300 Navara)

Рет қаралды 12,620

11 ай бұрын

EGR Cooler fault and replacement on a Nissan Navara D23 or NP300.
In this video we show you how to replace the EGR cooler on the D23 Navar behind the turbos on the right hand side of the motor. The fault we had was an exhaust leak from the actuator on the EGR cooler. 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 14 15 16 17 18 19 20 21 22 23
#automotive #mechanic #nissan #repair #tipsandtricks #nissannavara

Пікірлер: 36

@MrGary8839 22 күн бұрын

Excellent vid, used this to change mine that had a spindle broken inside. I personally took 4 days to get this out and back in but coukdent have done it without your pointers of what needed to be removed. Many thanks saved my a lot of cash .

@gettingitdone1 22 күн бұрын

@@MrGary8839 glad we could help you out. Thanks for commenting.

@canalsemnome6980 8 ай бұрын

It took me all day to do this work, some rusty screws and nuts, the video helped me thank you

@user-my8go6cc2v 10 ай бұрын

Consulta Si pierde aire por el actuador es por que esta mala el enfriador de la egr ?

@JKMotors9040 6 ай бұрын

He buddy did you fase problem with rear turbo vacuum pipes and any low pick-up problem after tihs work

@gettingitdone1 6 ай бұрын

Hi there, no we had no issues with either.

@cruzeduardoguidablanco4241 Ай бұрын

Hola buenas tardes , disculpe quisiera hacer una consulta tengo una np300 2018 el problema que tengo es que no calienta la calefacción y ninguna manguera del radiador ni de las calefacción y echa el agua al depósito del radiador

@gettingitdone1 Ай бұрын

Is the thermostat stuck open? Start it from cold and if the bottom and top radiator hoses both get warm at the same time, the thermostat is probably stuck open.

@blueboy490 9 ай бұрын

Have this problem on a 2017 can any tall me how long would this job take

@gettingitdone1 9 ай бұрын

Hi there, we charged 6 hours on this, that included working out what we needed to do, being our first one. But gives an idea for quoting purposes.

@davidfoggy7045 2 ай бұрын

Thanks for the video mate, helped heaps! is it possible to just remove the whole cooler, link coolant lines together and block the exhaust ports?

@gettingitdone1 2 ай бұрын

There's a good chance you would end up causing faults for reduced EGR flow, I would think you'd be going down a rabbit hole of problems.

@tonyp6088 2 ай бұрын

would it be similar for the D40 engine? Cant find a single video on it anywhere.

@gettingitdone1 2 ай бұрын

Hi there, totally different on the D40, but much simpler too. The cooler on those is at the front of the motor. I haven't done a video on one yet, but there's a couple of vids on KZfaq that show what it looks like and where it is at least.

@gettingitdone1 2 ай бұрын

This one is probably the best kzfaq.info/get/bejne/iLSTp8pqsZOraH0.htmlsi=1MaVOz4bmtlHddXo

@brittenv1000 10 ай бұрын

I've just done mine. Managed to get it off without removing exhaust manifold

@gettingitdone1 10 ай бұрын

Yup, don't need to remove the manifold. Only the front turbo.

@badsaiyan07 Ай бұрын

Can the cooler leak exhaust gas?? I have one that smell bad exhaust fume on where the exhaust manifold is Please help

@gettingitdone1 Ай бұрын

Yes EGR coolers can crack and leak exhaust files externally. You can cut a length of garden hose, put one end to your ear, move the other end around the area you suspect the leak is coming from (with the engine running). You should be able to pin point exactly where the leak is.

@daskalosx 10 ай бұрын

Except the cooler does it needed any other part like gasket?

@gettingitdone1 10 ай бұрын

Wouldn't hurt to replace all of the gaskets, if you can get them. Otherwise most of them are steel gaskets that can generally be reused.

@781Tomahawk 18 күн бұрын

How difficult is this to do if you’ve not got loads of experience in mechanics? I would be keen to try this myself

@gettingitdone1 18 күн бұрын

Hard to say, but I'd think you would want to be a reasonably handy DIYer. If you have some experience, you could do it, it may just take longer to navigate through, if you have no experience I'd say take it to a mechanic. Knowing that those banjo type oil feed fittings need copper washers on both sides of them will help avoid disasters too.

@powderboy91 10 ай бұрын

Have the same fault on my 2016. Not looking forward to replacing it :)

@JvideoCreation 2 ай бұрын

I have YD25 ENGINE. Have already new head gasket, thermostat,radiator caps. But main problem is still..All coolant move to reservoir tank could lead to overflow and overheat again. Is it posible for that egr cooler is cause of this ? Thanks😔

@gettingitdone1 2 ай бұрын

Yes it could be a cause. Does the coolant move to the bottle all the time or just after it overheats?

@JvideoCreation 2 ай бұрын

@@gettingitdone1 yes moves all the time. 1 minute after. Even in idle. Coolant move to the tank. But the temperature is normal. If i stay maybe 1 hour the tank will overflow posible to overheat again

@gettingitdone1 2 ай бұрын

@@JvideoCreation ok, can you try bypassing the EGR cooler, take the two hoses that go to the cooler and connect them together, with a pipe or connector. Then run the engine and see if the problem stops. Then you will know for sure if it's the cooler that needs replacing.

@JvideoCreation 2 ай бұрын

What about that tube from turbo. Theres a water flow in it right ? Could it be posible thats where the problem ?

@JvideoCreation 2 ай бұрын

@@gettingitdone1 ok bro. Thanks . Really appreciate it. I will try. Then i let you know the result.☺️