I repaired this Drive Shaft size so I hope you like our work #Transmissioncross #truckdriveshaft
Пікірлер: 37
@ernestimken69692 жыл бұрын
Talk about working dangerously! These guys have no injury protection AT ALL!
@paulorth22512 жыл бұрын
The best part is all the fine tuning at the end with the hammer.😁👍🇨🇱🇺🇸
@honkie2472 жыл бұрын
The universal joint is binding because the caps were installed with a hammer and not pressed in. To compensate for this, you beat it with a hammer until it either moves freely or submits. No watchmakers in this country.
@piyushgamit95522 жыл бұрын
Very nice
@peterraboni1197 Жыл бұрын
My opinion they should be pressed in.
@banuamekanikal454 Жыл бұрын
Good job my you always be healtyhy
@harjootmankoo24542 жыл бұрын
We need worker like this.... In india punjab ludhiana..... Good sary...... Accomdation will be provided
@AbdulHafeez-cq6oo2 жыл бұрын
good job
@johnthomas-km2bf2 жыл бұрын
Don't beat it with a hammer, Don't beat it with a hammer, Don't beat it with a hammer........he beat it with a hammer.
@tonyschiffiler48162 жыл бұрын
Had a press back when I was a teen , did this several times with out a hand sledge .
@Rcmetal2 жыл бұрын
Excellent work. 🇵🇹🇧🇷
@johnnyfannucci2 жыл бұрын
I’ve done loads without a press, if you hit the shoulder of the yoke with a hammer, the shock forces it out the front.
@greatgood53212 жыл бұрын
Salute to,all recondition automobile mechanics.
@rescuemehanicalthing2 жыл бұрын
Good work 💕
@Vip__honey2 жыл бұрын
Amazing video 📹 👏 ❤ 👌 🙌 😍
@sanjaykisen25242 жыл бұрын
dont how long this joint may stand after hammering from all directions. it may be the job done in suburbs where correct tools are not present.
@primangoprek86272 жыл бұрын
Kerja bagus kawan
@khankhan-ge6oi2 жыл бұрын
How you say nobody can do this thousands mechanics available in Pakistan they can do this.
@nivaldonunesdiniznunesdini20302 жыл бұрын
Gostei desse tipo de cruzeta não é trava elástica para prender a cruzeta é uma trava como de ponta de carcaça interessante
@stottybox31852 жыл бұрын
Shouldnt the grease nipple be at the shaft end and not the flange side. This may cause access problems when (if) greased.
@puspocempaka2 жыл бұрын
Makasi pak ilmumya
@TIMUR-ASKET2 жыл бұрын
😳😳😳
@amazingthingofficial29232 жыл бұрын
Nic
@joshkarena3058 Жыл бұрын
Done plenty of these, less usage of the hammer to reassemble though.
@trisnomechanic69852 жыл бұрын
Nice
@SalimKhan-fm7qr Жыл бұрын
Jra sounds ke sath video banayega. Please
@giangkubota2 жыл бұрын
Comment giảng kubota nhé Ni
@brucegissing9465 Жыл бұрын
Do not put a uni joint in this way you will pick up one or two needle rollers and caps will not fit down
@davidhile5363 Жыл бұрын
If at first you don’t succeed, use a bigger hammer !!!
@abdell2044 Жыл бұрын
Bravo 👍
@graemewhite5029 Жыл бұрын
Anyone know where I can buy one of those "tuning hammers" or maybe those sockets that slip at the correct torque setting ? 🤔
@SalimKhan-fm7qr Жыл бұрын
Jab parts kholte ho tab uska name bataya karo please. Or uska kam bhi bataya karo ki uska kam kya hai.
@mikespain8655 Жыл бұрын
What about greasing it?
@delboytrotter79022 жыл бұрын
Anyone can do that !!! Big difference is tho, that most of us would do it properly. He doesn't even have the correct size spanner ffs !