NOT GOOD! MY CHEVY C10 DOES SIXTH GEAR, 200 MPH BURNOUTS AND GOES HOME ON A TRAILER!

Рет қаралды 898,400

Жыл бұрын

In Episode 230 of Mike Finnegan's Garage, I venture to Bowling Green, Kentucky, the Home Of Holley and Jessie's Garage, a local shop with a sweet chassis dyno. Jessie was kind enough to allow us to strap my 1967 Chevrolet C10 to the dyno to finally finishing tuning the Terminator X EFI system. The end result was unleashing an additional 200 hp from the Chevrolet Performance LT4 supercharged engine and doing epic burnouts in every gear of the six-speed sequential gearbox.
Want more info on the Holley Terminator X efi system? Go here:www.holley.com/products/fuel_...
Want to see the 6xd Billet Sequential transmission? Go here: 6xdgearbox.com
Those Mickey Thompson Street Comp tires can be found here: www.mickeythompsontires.com/s...
The C10 runs Forgeline wheels: forgeline.com
Jessie's Garage: / jessiesautogarage
Holley
Thanks to Jeremy Stoermer, Steve Sparkman and Tyler Pleban for helping to film this episode.
Want to grab the new "I Love Fossil Fuels" hoodie? You'l find it and a bunch other cool swag at www.fsmgarage.com
As always, thanks for the support!
-Finnegan

Пікірлер: 951

@seanlinne8383 Жыл бұрын

Sounds like it`s time for another muscle truck shootout! Finnegan vs. Freiburger vs. Costa vs. Dulcich

@stevenichlson6085 Жыл бұрын

Yes, make this possible 👏 people. Like the comment.

@jammerz63 Жыл бұрын

Don't forget tony Angelo and vice grip garage.

@jameseastwood4984 Жыл бұрын

Bring Tony Angelo in 👍👍👍

@katherinecurtis1747 Жыл бұрын

@@jameseastwood4984 they cant he left and went to hagerty

@jamesnelson5741 Жыл бұрын

Hell yeah!

@destructionnl8165 Жыл бұрын

Finnegan: Has 2 ramptrucks. Also Finnegan: Puts the C10 on a trailer.

@Crafftyyy Жыл бұрын

too low to get on the ramp trucks

@WillyG3234 Жыл бұрын

@@Crafftyyy it lifts up

@getchasome6230 Жыл бұрын

@Crappyyyyy Wat?

@michaelcouey1383 Жыл бұрын

@@848evo4 LOL I'd love to see what you have that puts all their stuff to shame. I don't see any videos on your page?

@earnestbass1232 Жыл бұрын

@@848evo4 half ass but not garbage they have very nice equipment just thrown together. I agree I wouldn’t let most of these guys work on my junk but Steve brule.

@benjones3329 Жыл бұрын

Great to see you and Newbern spending some time together, glad he could make it

@joefries365 Жыл бұрын

is newbern not on the channel anymore?

@djd1162 Жыл бұрын

I felt the same. You never know what happens behind the scenes and it’s good to see their friendship is still there.

@danmyers9372 Жыл бұрын

@@joefries365 - No, he left to run his own KZfaq deal.

@Peron1-MC Жыл бұрын

@@danmyers9372 and more importantly be with his family more.

@isaaccan3155 Жыл бұрын

They still do Faster with Finnigan together. Dave just was working way too much and couldn’t be with mike all the time. The man has a family too. All of these guys, including Freiburger work their asses off doing multiple tv shows. Filming almost every week.

@enginebae3471 Жыл бұрын

Ahhh, the sound of my people

@J.C... Жыл бұрын

Straight up! 🤣👌

@brandonsearle990 Жыл бұрын

Hell yeah brother

@BUILTFORDTOUGH79 Жыл бұрын

🇺🇸🚳

@studbolt5627 Жыл бұрын

Hell yes

@rowdysincoherentrambling1426 Жыл бұрын

Being a fan of Finnegan’s builds is brutal. You see an awesome project come in, but you know he’ll throw 10 others in the mix and you have to wait a couple years for them to be finished. But it’s always worth it!

@JRube123 Жыл бұрын

kinda like @doitwithdan

@la_plata3588 Жыл бұрын

The recipe to keep you coming back.

@trumbley22 Жыл бұрын

Literally every popular car KZfaq channel. It's called automotive ADD.

@trashbandit2449 Жыл бұрын

@@trumbley22 this is a 6+ year old build though haha. Not a ton done to it for a while

@trumbley22 Жыл бұрын

@@trashbandit2449 So he's a normal car guy? Haha.

@leoreid5649 Жыл бұрын

Great to see you and David together for shenanigans again.

@al9030 Жыл бұрын

I wish I had connections and sponsors like Finn..Life would be good

@thopf3590 Жыл бұрын

That was awesome to see 6 th gear burnouts. Dave’s bel air sounds rowdy.

@peterrobins3708 Жыл бұрын

That truck would be illegal in all states of Australia. Fun & personal enjoyment was outlawed a long long time ago. In Australia, those that have big non stop smiles, they're probably auto-outlaws Great videos to watch as usual. Keep on keeping Mr F and other Americans like him 🙂

@RoB_666_ Жыл бұрын

I absolutely love the fact that David isn't scared to lay the boot in and whip it when most wouldn't, much respect from 🇦🇺

@Alwhite1929 Жыл бұрын

Damn, that first pull after the initial adjustments was night & day difference. Awesome

@GearheadOutlaw Жыл бұрын

That truck is the new standard for how to build trucks, Wicked

@kylelanger4234 Жыл бұрын

MAN!!! Newbern's 57 looks and sounds amazing! Perfect patina, great looking trim, nice wheel fitment and wheel combo, and it sounds like it's pissed right off!!! Love it!!

@tesla747 Жыл бұрын

I think someone is trying to scam us.

@BrettGuffey Жыл бұрын

Such great sunday morning content. Love watchin Finnegans garage with a cup of coffee

@gteefxr3094 Жыл бұрын

It's better with a couple of shots and a beer.

@leecavalla5917 Жыл бұрын

There is something with the old metal I could not stop smiling thanks so much for the 57 footage

@brianlafollette7530 Жыл бұрын

It is good to have friends that know things. Nice job Holly

@Joeboost8805 Жыл бұрын

That SOUNDS INSANE , AND THE THROTTLE RESPONSE IS GONNA BE HARD HOOKING UP!!! SWEET BUILD

@Joeboost8805 Жыл бұрын

WELL WORTH THE CLUTCH!!!

@SoI_Badguy Жыл бұрын

HELL YEAH BROTHER AROOOOOOOO

@charlesgraham9954 Жыл бұрын

GOTDAMN..!! i love the sound of an engine. every new engine iv done, iv laughed like a schoolboy hearing them run for the first time.

@94XJ Жыл бұрын

31:06 I've sad that quick "ok" a few times in my life... that's joy right there😂😂

@Cybergasm01 Жыл бұрын

Love the little convincing it takes Dave to keep doing burnouts lol Anyone else notice that Mike and Dave were twinning at the end of the video LOL

@michele215 Жыл бұрын

The truck has always been my favorite build on the channel. It sounds awesome. I was all smiles and giddy the entire burnout session! Glad Newbern made the trip as well. Thanks for the amazing content!! #burnouts4life

@benbrown2119 Жыл бұрын

This brings me back to when I swapped a 455 Olds and 200-4R into my 1981 Oldsmobile Delta 88. Did a 4 gear (plus lockup converter) standing burnout when it was done. The picture is way back in my Instagram feed.

@al9030 Жыл бұрын

Finnegans Garage getting more views then Billion Dollar "Sell-lOut" Motor Trend..Love It..Finnegan You Da Man!!!!

@coryhall561 Жыл бұрын

Super pumped to see Newbern again, and his 57 is looking Badass!!!

@scottburrow8717 Жыл бұрын

Look who it is. David Newburn on the channel again. You guys are so good together.

@justinbatchelor2418 Жыл бұрын

There is nothing more bad ass than burnouts but, a 6th gear burnout is arm pumping bad ass.

@docsgearheadgaming2503 Жыл бұрын

Great to see these two back together! Sorry about the clutch, but thanks for the entertainment!

@scottimusgarrett15 Жыл бұрын

Nice to see 12-Volt come out and do some vulcanizing!😂 And you looked like Spicoli gettin' out of his van after lunch after the 6th gear burnout. Nicely done! Too bad about roasting the clutch, though. I guess we'll see it again in a year or two!😂 ✌️❤️🙂🇨🇦

@CamaroStuff Жыл бұрын

Damn! Mike, talk about an episode having you on the edge of your seat. Absolutely Epic!

@choony1970 Жыл бұрын

That C-10 is the most badass truck EVER !

@AB-80X Жыл бұрын

12V Dave just elevates things to another level with his presence. Was nice to see a dyno shop with a good honest dyno and a tuner who knows his stuff. Not entirely sure how you guys ever thought it was correct that it made 650 to the wheels on that other dyno. Just goes to show that the shop you initially dynoed the C10 in does not have an accurate dyno. Yes 10-20 hp is variations between dynos, 90 hp is not, that's an operator who's does not have his equipment in order or is deliberately inflating the numbers. I definitely would not use Moe's after seeing this. But now you know where to go with the other cars to get accurate numbers. Very cool.

@greghayward4815 Жыл бұрын

Thanks for introducing all of us to this drag strip. I have gone out of my way a few time to visit this strip. Wish there were more like this around the country.

@MitchZero9 Жыл бұрын

Wow the old Ramp Truck 454 has a new lease of life!!!! 💯

@amybot7182 Жыл бұрын

Man i love it when people like that come out and help. Eventually I plan on putting a little holley sniper on my 74 super beetle

@buckykattguitar Жыл бұрын

I’ve got a 63 bug with a 2275 I did that with. Single best mod I made on my car. You will not regret doing it.

@michaeltucker4875 Жыл бұрын

You guys are the right kind of nuts!!! Being from Cartersville,ga it’s good to see some down home boys doing it!!!!!!!

@nicknamebulin889 11 ай бұрын

Glad there’s a tach on the passenger side. Fun to watch!

@Toddo-ld5ml Жыл бұрын

I love Sunday's great to see you and Dave out there ripping you rides. Glad to see the C10 finally straightened out

@mrmoss149 Жыл бұрын

I know it's been said before-but you guys are INSANE. Lovin' it!

@michaelgf8840 Жыл бұрын

Wow, what a coincidence! My 2003 expedition has a 2003 expedition rear end in it also!

@-g-4356 Жыл бұрын

C10, Bel Air,burn outs, Fin and Dave 🤘

@stevew9247 Жыл бұрын

I guess my question would be, Why did Holley sell a product for an application that would never work as shipped, and quite obviously had never been tested? It's been 3 + years now and the fix isn't yet released. How much money and time have buyers spent trying to make a defective system work?

@gkixe4y Жыл бұрын

Bacause they don't have to care.

@dickfitzwelliner2807 Жыл бұрын

Probably because it was setup for an ls?

@heytonyman Жыл бұрын

Just like he said in the video… it’s made and advertised specifically for LT1, L83, and L86. Not LT4.

@user-neo71665 Жыл бұрын

He is trying to use a setup designed for an LS engine on a LT engine. I'd almost go out on a limb and say it most likely was designed for a na LS on a supercharged LT throwing another wrench in the mix.

@dnchevyguy3 Жыл бұрын

Nothing about it was defective. He was trying to run it on an LT4 when it was specifically sold to work with LT1 injectors. Looks like the new version will work with the LT4 injectors as well though.

@brianrichardson7946 Жыл бұрын

Love Love love this truck and can't wait to see a heads up between freiburger and finnegan

@TheTulerie Жыл бұрын

I'm so excited to see this truck finally get some attention. Probably one of my favorite vehicles Finnegan has!

@TheJkc81 Жыл бұрын

To me, everything is perfect about that truck. Bare metal everywhere, forgelines, sequential trans, dry sump. Love that truck!

@thman6453 Жыл бұрын

Man 12 volts 57 sounds great 👍 nice job Dave

@cryptoredneck8255 Жыл бұрын

I just got into tuning my truck, I'm so jealous of how consistent your idle is brother!

@ajherman Жыл бұрын

That 57 is beautiful. Love the shine of the trim and wheels contrasting with the patina. Not to mention it sounds rowdy as hell.

@moparracer76 Жыл бұрын

28:54 "Valve float is the Cadillac of Rev limiters" -Shane Whalley

@XStream09 Жыл бұрын

If you are going to do standing burnouts like that again, put in an external gear indicator for those watching, that would be awesome 😮

@charlestorruella8591 Жыл бұрын

there one in the dash didn't you see him point at it and say this is so you know what gear I'm in don't you feel stupid now

@static_bolt Жыл бұрын

@@charlestorruella8591 EXTERNAL, as in outside the cab for spectators. you clearly have excellent reading comprehension

@garrettwalton7461 Жыл бұрын

@@charlestorruella8591 man there is zero need to be this rude, get a grip

@jont8707 Жыл бұрын

Dave built a sick 57 love how that thing looks

@lauriehenderson9915 Жыл бұрын

Stupidity squared!

@jont8707 Жыл бұрын

@@lauriehenderson9915 do what

@user-ih7gc7dt9l Жыл бұрын

Direct injection in the aftermarket scene is a new one on me. Must have been living under a rock!

@PullStartStables Жыл бұрын

Thank you Chevy, for so much awesome! That ‘57 spinning sprinkle donuts and the C10 as a whole is just Bacon!

@demonic477 Жыл бұрын

you should be able to re valve the master cylinder for both sets of brakes you just need to know what the factory Ford master cylinder put out for pressure and match it . or get Wilwood to do it for you they love that kind of problem If you call and ask them they will figure it out they even built a set of custom brakes to fit Model A's for J leno it's what they do

@nocoasthero1204 Жыл бұрын

I love this truck. I’m currently in the process of building my 78’ LB gonna lay out like a beached whale 🐳

@mwaynem Жыл бұрын

It's strange how some sounds can take you back 45 years. I owned a 67 C10 in 78. When you closed the door at the drag strip I instantly remembered that sound. Only old trucks make that hollow clank. Again thanks for sharing 👍.

@LT4Nova Жыл бұрын

Awesome! I've been waiting for LT4 SUPPORT!!! THANK YOU.

@bigfootgarage2201 Жыл бұрын

I still think the truck would look badass in the GM crystal white frosted color from the CTS V with black chrome on the trim

@trumbley22 Жыл бұрын

🤮

@danielkanewske8473 Жыл бұрын

Good to see Newbern again

@benbelton6632 Жыл бұрын

I can honestly say this is the only project I want to see in paint.

@jagharingenyoutube Жыл бұрын

Thats called cheating :D With the rockers on the ground the weight isnt on the tires

@mollyv2755 Жыл бұрын

Despite the economic downturn, I'm so happy 😊.I have been earning $ 60,200 returns from my $7,000 investment every 13days✓

@hannahjosephine8119 Жыл бұрын

That's amazing, I have been hearing about Mr Alex Adelman and their geniuses mind in the crypto market, please how did you earn such good amount?..

@user-uz6hk5pu7s Жыл бұрын

I think I'm blessed because if not I wouldn't have met someone who is as spectacular as expert Adelman I think he is the best broker I ever seen

@tysonbeckford9248 Жыл бұрын

The crypto market is highly profitable with an expert broker just like Mr Alex Adelman . I got recommended to him and since then my financial life has been a success.

@craigjensen4179 Жыл бұрын

Finnegan is definitely my favourite KZfaqr. Even better when he's with Dave Look forward to every episode 💪💪

@theglitch99 Жыл бұрын

A day w/Finnagans would be a BLAST!! DUDE HAS BAD ASS TOYS! BEST OF THE BEST!!

@leebrown2063 Жыл бұрын

Watching this is a blast from the past.used to watch roadkill religiously

@jameseastwood4984 Жыл бұрын

Great to see Newbern. That 'second guy' on the channel can be super important. A lot of folks, me included, identify more with the helper (2nd guy) than the main guy, simply because we probably don't see ourselves in the main guy role.

@XBullitt16X Жыл бұрын

One of my favourite cars and build's of Finnegan's, I hope it finally gets painted and completed, will look awesome when its done.

@bryduhbikeguy Жыл бұрын

At 39:02,I thought it was just the headers glowing behind the front tire...Everyone go look starting 1 second before and frame by frame it..I'll wait...Pretty awesome shot huh?Truck sounds so good now.The 57 is Wild.Congrats David.

@jahmackey Жыл бұрын

Great show! I think the first time I saw your channel was when you were building or rebuilding your c10 with your friends in a week...very cool the truck is beautiful....see you and Neubern(cksp) was awesome....I think the best part of the show was watching two friends having fun together! Thank you for sharing!

@gregsegrest4126 Жыл бұрын

I've always like the 67-68 c10s after Stacey David built Copperhead and I'm a diehard squarebody guy but I've never had a dream truck until you built this this. Words can't do justice to describe that beauty.

@kenadams2799 Жыл бұрын

Don’t forget to run, Lucas fuel additive in that direct injection system. I had one of those with real high rail pressure and it goal two injectors. I started running Lucas fuel additive as per the bottle and never had another problem. Awesome work over there. You are my go to channel every Sunday morning because it makes my week better. Keep up the great work.

@Buffrt66 Жыл бұрын

Crazy!!!! I love seeing all this new tech. being worked with and adjusted, very interesting.

@stevenrobertson9583 Жыл бұрын

Now that’s the Old School hot rod, big fat tires in the bag a low thin wheels in the front and sitting high in the rear! Just Awesome 😎, Beautiful Performance thing of Art!!!!!!! Oh almost forgot NO NOS GOING TO THE MOTOR, only thing NOS was used for was to cool the intercooler so you was making the air cooler and thicker going to the intake!

@jwray9799 Жыл бұрын

I miss 12v Dave... you need to try to get him back,, you two work together,,

@barrishautomotive Жыл бұрын

Great seeing Newburn. His channel is pretty cool too.

@randalldavidson4483 Жыл бұрын

Love seeing Newborn back. Those two are awesome together.

@frizzletits8511 Жыл бұрын

33:24 - supercharged from Down to the Bone started playing in my head 😂

@djchanga2216 Жыл бұрын

Probably the best rig in your collection …I could just image one of those milk run videos 😎

@goatflieg Жыл бұрын

How many of us instantly yelled "NEWBERN!" at 27:42? I know I did. Crusty's lookin good... and so is the C-10.

@daboenterprize8265 Жыл бұрын

Awesome too see the c10 finally getting it done and seeing Newbern and 57 was amazing ❤❤❤🎉🎉🎉🎉🎉

@MadmanJnr Жыл бұрын

Man Crusty looks mad and sounds great doing skids... 2nd that for the C10! Massive thanks to Paradise drag way for letting the boys play!

@Big-John Жыл бұрын

You both are having to much fun! I love it! Glad you got the truck figured out! Keep up the great work 👍

@nickz6143 Жыл бұрын

What a beast of a truck. This C10 is monsterous😂

@bigblocklawyer Жыл бұрын

Enh...customer at the Corvette restoration shop, where I worked in the '80s to mid '90s in St. Louis used to hang around every day while we restored his '65 396 Roadster. He bought an old, beat-up 1980 1 ton St. Louis Gas Company Chevy truck and built an actual, no shit, nascar motor and put it in the truck. He bought cans of Turbo Blue for it, and it was a 13:1 legit cup motor he bought from a friend of the Wallaces. It had a 4.10 locker and an SM465 trans. It had the biggest header tubes and collectors I'd ever seen, bc they were Cup headers, and they were open. No other exhaust whatsoever. He left out of the shop on a Sunday morning, right as the Catholic church was starting its service. I can make myself remember, now, 32 years later, how I had tenitus for 2 days after he did that burnout in front of us. It was so loud that it made us disoriented. We used to run L-88s and 435's on a break-in stand before we put them in the cars, and they sounded like Teslas compared to that truck. So, loudest truck, EVER? Maybe not.

@Mike.hobbies Жыл бұрын

Quality episode,so good to see the truck going well.. really loved this Mike and great to see you with Newburn again also. Love David's channel I highly recommend it to all

@ronniebenoit4081 Жыл бұрын

science class project : burnouts +shenanigans =..... A++

@Joebro200 Жыл бұрын

What a good Sunday. Not only getting a sick Finnegan video, but its of the C10! Sounds insane. Building a 67 short bed fleetside c10 right now. Butternut yellow. Wanting to build a 496 or a 555 big block for it with a Tremec t-56 magnum. Just need to find a good core! It'll be a 496 if I find a good gen 4 core, or if I wanna spend the extra money a Big M Dart block would be sick... either way the money will make this project sit for some time more.

@thenamesPRINDLE Жыл бұрын

I haven’t been following along much this build so I must say DAYUM! thing is a beast but I love the dual screen for the passenger!

@davidriseley6811 Жыл бұрын

No words! MAGIC!!…cant wait for this one

@SubieWan Жыл бұрын

This thing is just incredible. Been wanting more of the C-10 content.

@doublehelix109 Жыл бұрын

i mean your shed vids are cool and all, but its SOOOOO good to see some skids again!

@mickc4633 Жыл бұрын

Nice truck I had one of those back in the day. Factory big block, air everything short bed . Wow technology wow.

@cavemanstan9477 Жыл бұрын

Finnegans Garage where they are science adjacent

@garyseaton4619 Жыл бұрын

I'm not going to pretend to know what's going on because I'm not an etech, but this truck you've built is BADASS... Watching for the fun aspect and the knowledge is amazing...

@FinnegansGarage Жыл бұрын

thanks, Gary!