Dolmar/Makita have always made great saws. Too bad Makita is discontinuing all gas saws.

Loved the video. Crazy how good it was

They’re beautiful saws.Nice work on that!

Had my dolmar 6400 since 2008, had firewood bizness and cut 300 cords a yr, after 4 yrs i dont cut firewood but gona start climbing again, saw still runs

Lotta tricks on Dolmar/Makita to learn but very easy to work on once you get there. Super running saws, better ported, carb modded and unlimited coiled!!! These saws are hot rods out of the box. Good video!!!

I really like my 7900 I’m on the fence as to whether I’m gonna port it or not. I’ve got three of them so I probably will at some point but I’m not in a hurry.

I gotta get my greedy little meat hooks on a Dolkita! Lovin what I saw. Great video Boedy!

I don't personally know, but the scuttlebutt is that the low top filter makes more power. I had a German Dolmar years ago, and actually put the high top kit on it right after a got it. Wasn't until after I had sold the saw that I came across that information.

Got the saw today. Ima gonna run it right down to my cousin. I'll tell him he's got to run red armor.

I always liked the Dolmar saws,but like you said kind of different to work on.

A sleeping legend.

Damn sure looks nice. Just wish they had parts or dealer presence. I have literally never seen one in my area.

Pretty damn strong even without the porting

I have a ported 7910 low top. I like the looks of the HD setup but heard it hurts power. The low top doesn't have that piece in between. You can access the carb by pulling the top cover. One thing I don't care for is that, like you did, when you shit it down it pulls on the recoil. I pull it out as well. Absolutely love the saw and it gets used most of anything I have. Tree monkey did mine.

I like my 6100. Whole top cover comes off with a few clips and the big air filter is held on with a single nut. Definitely different from that beast you have there

The best thing about the 7900 is you could easily build one from an inexpensive used 6400. I loved my 7900 and was used to the quirks but sold it for a 562xp to shed a bit of weight. Now I run all Huskys and Jreds. Just wish I could buy the Autotune diagnostic tool…

I don't know what those run for compression but the 6100's are nuts from the factory. Mine is at 200psi currently.

nice

Wish you would have addressed the real issues with the 7900 and that’s the carburetor and exhaust. On mine, the high jet doesn’t seem to be adjustable. The screwdriver fits just fine but it doesn’t turn. The exhaust is very restrictive but being aluminum (I believe) it’s not like I can cut it open, remove the inner crack pipe and weld it back up like you can had it been steel. Possibly it’s stainless and not aluminum but it’s not carbon steel. Maybe someday, revisit the Makita and let us know how you addressed those issues. It runs decent from the factory but that exhaust cuts is restrictive enough I think it’s down about a horsepower from what a good 80cc saw should have and without being able to adjust the high jet I’m leery about opening up the can. Anyway, just some thoughts. Likely you’ll never see this anyway. Appreciate your channel 👍🏼

How did you do the muffler mod

Man that’s the best saw in its class thing rips

👍

TNL you should port that 500I.

👍s🆙Big Guy!

The brake spring is a nightmare.

A bit late to be complaining. Dolmar/Makita discontinued their gasoline chainsaws. 2 dealers in my area closed shop.

I have made more power with coils on some smaller saws so I’m sure it could be the same with that saw but man that thing don’t need anymore power

that's why i stick with husky and stihl

Makita is a Japanese corporation. Are you calling this German because of Makitas acquisition of Dolmar?

Why does your twin brother win every time? Lol.

be faster and stronger than 592xp, this statement is just for laughs hahahahahah you are a true comedian I bet even this 7910 ported is slower than the stock 572xp