Living in the northeast, where we have basements for our mechanical systems, it's strange to see so many HVAC systems lying on their sides in crawlspaces and attics.
@Bob.W.8 ай бұрын
Even stranger are the package units sitting on a slab or in the dirt outside.
@GeneG-wk2mz8 ай бұрын
In Atlanta my dads in tight crawl space then this
@kw_boeing8 ай бұрын
And you guys get all the fun stuff with oil and boilers! Here out west it's all gas furnaces located in the basement or closet.
@pineychristian8 ай бұрын
I live and work in NJ and it's very common to see them in crawl spaces. It's not the ideal area but being in the HVAC trade I've seen many in crawl spaces.
@zack99120008 ай бұрын
crawl spaces are just a lazy mans basement
@CubbyTech8 ай бұрын
Unit is pretty clean - I'd estimate another 10 years left in her.
@Wolfhound.8 ай бұрын
gosh the accommodations is nice get to set and relax while working
@anthonyelectric60458 ай бұрын
The fact they had a chair ready for ya was priceless lol.
@joeshearer12478 ай бұрын
Good job on that screw uncle Ted ❤
@blake82978 ай бұрын
haha he got'er back in there
@jordandarby34468 ай бұрын
I’ve been doing hvac residential for 4 years now and I find it funny to see old grande aire products from Nordyne and how they are still around, but now grande aire is ICP and nordyne is garbage. It’s funny how the names cycle and change.
@user-su5ft8lc9q8 ай бұрын
Nice the home owner provided a nice chair for your confort to work on their furnace.!!!!
@Straycurrent8 ай бұрын
I’ll be sure to tune in for the new install episode. I want to see how many UV lights the customer requested 😂
@Eddy638 ай бұрын
That was a great call on that screw ... I've had em go Catawampus on me before and I had to lay down in the crawl space for a bit Good vid Sir ... Thx
@rileydavis4358 ай бұрын
That’s sounds like Montana this year. We are in the highs of 50 degrees at the end of November. When it’s usually in the teens to negatives this time of year
@chatrkat8 ай бұрын
One UV light 😂 Two UV lights 🤣🤣 A slick salesman talked my neighbor into one 10 years ago with their overpriced and rather sloppy new system installation. Reminded me of the old car dealership scam selling the Paint Protection coating.
@AudiophileTommy8 ай бұрын
Are you going to install 3 UV lights 🎉😂🤣😂🤣😂🤣😂🤣😂
@steveberman36958 ай бұрын
I enjoy your vids! I hope the work on your building after the flood is progressing well!
@RichB03308 ай бұрын
Really clean for 20 years old
@chuckquinn80268 ай бұрын
Wow! Congrats on the job! 🏆🏆
@thecableguy11288 ай бұрын
That might be the dog house. Or a hideout for the man of the house. 😂😂😂😂 🪑 under the house. Could have been where the male kid was learning about his blank. Watch out for tissues and petroleum jelly products.
@pineychristian8 ай бұрын
"Not to bad of install" pretty bad if you need to use block to support furnace. Hang the furnace with unistrut and isolators. If it is done correctly it will not block any access to any of the doors.
@TedCookHVAC8 ай бұрын
Makes noise in the house. Vibration etc. I prefer a solid block foundation. Just my opinion.
@pineychristian8 ай бұрын
@TedCookHVAC I've seen hundreds of furnaces and air handlers installed on unistrut. When done correctly there is no vibration or noise. I think installing furnaces on block just looks cheap and there is no pride in the job. Just my opinion...
@charlesharris40218 ай бұрын
Love your videos and your work ethic. Question: Do you like UV lights on the air duct returns? Are they useful? I have had one, Air Scrubber, installed now for 2 plus years. I changed the bulb after 2 years as reccomended. When I did the cage was about 1/4 blocked with dust. This year I will remove it after one year and clean the cage. Are they worth it?
@c.blakerockhart11288 ай бұрын
Charles, I know that your comment and question were meant for Ted. But it was posted 8 days ago and nobody has replied yet. I have been an HVACR installer and tech for just under 20 years now. My "Personal opinion" is that the UV lights DO actually work, but ONLY if they are well maintained. As for My own experience, I have found that if your ductwork is SEALED PROPERLY from end to end they are not necessary. If your Return duct is COMPLETELY SEALED all the way from the filter rack to the unit, and your SUPPLY DUCT is COMPLETELY SEALED from the unit to each run and each run is COMPLETELY SEALED all the way from the ductwork trunk line to the boot that holds the register for the release of the air, you should not have any dust or contaminants that are hazardous. Most dust and irritants are coming from the ductwork Not being properly sealed. If your floor boots (under the register/vent) have ANY GAPS around them no matter how small, it WILL pull outside air and contaminants such as dust/mold/mildew and smells from around it. If your ductwork is in the attic and is surrounded by insulation then you are distributing fine particles of the insulation throughout the house if the boots are not sealed properly. But the short answer is : In My opinion, the UV lights are a waste of money. You would be better off to have someone come in and seal EVERY joint of the ductwork with a paint like material known as "MASTIC". It is a very thick rubbery paint that is DESIGNED for ductwork.
@AudiophileTommy8 ай бұрын
A chair for you 🎉❤
@scottmaz40638 ай бұрын
Wow needed motor change the system instead. Cha ching Ted. Love customers like that.
@TedCookHVAC8 ай бұрын
Motor was a few days out from Nordyne or Nortech or whoever now... new system was in stock and they had heat the very next day..... not to mention AC was also leaking R22 the last 2 years in a row ... no brainer on the replacement system being the smarter option.
@throttlebottle59068 ай бұрын
I thought that screw was going to win and be flung across the crawlspace or left out. 🤣
@TedCookHVAC8 ай бұрын
I have done that before !!
@sknight03918 ай бұрын
😎👍😎👍😎👍
@zackmax71848 ай бұрын
Steve Lav had this Old Guy Spitting on Him Yesterday.
@valvemonky47348 ай бұрын
was funny but Steve told him hes not shy 😙🤣🤣
@cuthbertelitwaza94748 ай бұрын
Wanted his power venter replaced…..spit on it 😂
@zackmax71848 ай бұрын
We might need some heat tonight.
@laynesouth11988 ай бұрын
I have mini split
@dimbag18 ай бұрын
Good to see you mr. Ted but we need a video every day . And how the shop doing after the flood
@user-hv9gk5tc8z8 ай бұрын
I know how you feel about those UV lights 😂
@Newt37008 ай бұрын
I was wondering why you hadn’t posted in a few days…..👍👍👍👍
@javaonline8 ай бұрын
How’s the shop and drying out from the flood coming along? Have been wondering how you guys were doing since the flood vid.
@alanleelitvin48998 ай бұрын
Good to see you back Ted. How is the shop recovering project going?
@TedCookHVAC8 ай бұрын
Slow to get insurance to pay.
@gerardomireles1228 ай бұрын
No helicopter
@Ugurbado8 ай бұрын
Гуд!
@Garth20118 ай бұрын
Can't those motors be oiled? All that is wrong are the bearings are dry due to poorly used/designed bearings for the purpose. Usually the air isn't ideally clean and those tiny open to the elements bearings which get contaminated and dry since they are typically sleeve bearings vs. sealed ball bearings that provide longer service. I get it that as a business and for warranty purposes, a new condensate motor/fan assy is the way to go however, just for conversation, sometimes those will continue to run for years with some oil, something temporary while the customer thinks about their options.