I worked on my honda for the first time and broke a bolt on the valve cover. Smh. Glad this video was made. I even listened to the same song just for extra luck.

You're a lifesaver. I spent an hour using an extractor and this method took me all of 5 minutes. About to pick up a set of torx sockets

As a mechanic, I come across broken bolts often and spend crazy time to removing them. Your method, will work better than an extraction tool that often does not work. Thank you.

Probably one of the most useful Videos on KZfaq..... saved me a trip to the hardware store and the cost of a bolt extractor!

Worked like a charm, thank you!!! I had a broken bolt in the head of my 454. Used 7/64 for a pilot hole & then a 7/32. #27 torn & it came out as smooth as butter. You ROCK!

Bro i love you so much for this. Im a Machinist and ive been trying to get a headless thread out for like 2hrs. My shop doesnt have thread extractors, so i looked up your vid and it just saved my ass! Without your video, i wouldve had to scrap a $900 mutli inserted drill shank. Take my sub and like even if you never make another video

Store bought extractors were not working. This method actually worked great! Thanks!

Thank you good sir for this video. This video saved me. Had a broken bolt stuck in a valve cover. I managed to get it out. Thank you for your guidance. ✌️

I spent over 50.00 in Bolt Remover kits that didn't work, but this did. Thank you!

pulled me out of a deep mess as i had a set of long torques all the extractors to short you vid saved the day many thanks

Great vid and very informative. I had a similar situation with an exhaust bolt. What helped me was using a left hand drill bit. It hollowed out the hole as well as loosing it up. As soon as I put the easy out in the bolt it was loose enough to loosen by hand .

This works like a charm! Just extracted two snapped manifold studs from my RB25DET head!

Saved me from catastrophe . Thank you so much.

Just had to add my comment since this saved my ass. Had a speed sensor bolt that broke off in the steering knuckle. It was a fairly small 10mm bolt head to give you an idea. Used a 3/32 drill bit and a smaller T10 torx (figured I'd start there and go bigger if I needed). Didn't drill too deep for fear of not drilling perfectly straight, worked like a charm. Thought I'd throw my testimonial and numbers here in case it helps

Best video on KZfaq for this.Straight to the point and also have good music

Thanks! Just saved me so much work. Didnt even know that we could use those bits on a ratchet. Thanks

Hell, might as well give it a try. I ain't done nothing but screw it up so far.

Oh my goodness you Rock I had that screw out in less than 10 minutes best advice ever 💯

I did it and it work. Thank you for this video. Very helpful

used this on spark plugs works a treat, saves loads time

Thanks for this video!!!! I bought a ez out kit and it couldn’t get the bolt out but I used your method with a torx bit and it worked out better thanks again for the video 👌👌👌👍👍👍👍👍👍🙌🙌🙌🙌🙌🙌

Wow! I’m going to try this method. Thank you. 👌🏾

Very good, the best and simply solution that j've saw just until now.

Cool! By using this method I should be able to drive the broken bolts that held my ATV's skid plate to the frame out by reversing direction and actually driving them deeper in until they come out the other side.

Right on brother good hack. Use this on my John Deere lawnmower and it came out just perfect didn’t even have to go buy a kit thank you brother!!!👍😎

You are a life saver. This was the cheapest most effective method.

Excellent video

Excellent video! Thanks!

Thank you so much, im from Brazil It worked

Thank you worked a treat, saved me from a massive mess

OMG you came so close to fooking up your inner threads, Thank God you didn't or this would of been another video. Good stuff, Thanks for sharing.

You absolute legend. This saved me so much hassle.

Simple dude with a simple toolbox getting it done. 👍

Worked like a charm! Thx sooo much!!🙏🏽🙏🏽

Got a new sub cuz I just came across this problem 😂😂

Thanks brother this helped me. Easy out wasn’t working for me. I’m so happy 😁🤙

Thank you for posting. Going to give this a try.

so satisfying to watch it unscrew

God blesss this man It was hard for me to drill it so I used metal screw and the star bit and booom

This worked for me perfectly. I used a smaller size drill bit and a smaller size torx.

very helpful!!! i have a broken pcv valve and the thread part is in the valve cover hole gonna try with torx bits

That was very satisfying to watch.

Videos like these is why i love youtube

Thats awesome, I was figuring out how to deal with such bolt. Thanks 👍

your method is much better, i think. I will try using it. thanks

well done. Fantastic work.

Thanks man your video helped me an my brother a lot 👏👏👏you are awesome 👏👏👏

I tried it and it work as described, awesome 😎

You just saved me time, aggravation and money... Worked like a charm, thank you!

Man listen you just saved me so much money bro 😂 thank you for that hack 🙏 🙌

valeu muito a dica, retirei o parafuso com muitissima facilidade, parabens e muito obrigado

Nice.I definitely feel better just knowing some one else had success.

Thanks man helped a lot had to use a different bit but same idea

Awesome...quick and to the Point

Very useful. Nice. Very infomational.👍

Gracias por este vídeo, resolví lo de un perno roto igual al del vídeo y salió fácil

Thanks brother you saved me money and time

I have a bleed valve snapped off in the caliper. Most videos say weld a nut on the end. I can't weld so hopefully this approach will work. Thanks for the vid

Bonjour et merci énormément sa ma sauvé la vie vraiment le top vous êtes un génie bonne continuation merci encore

yes, I was doing that way 20 years ago before came out first extractors on the market :)

DANKE DU BIST DER KING HAT GEHOLFEN SEHR GEILE ZAUBER TRICK IT S MAGIC JEAH YOU ARE THE KING

Worked me for, thank you so much!

Thank you Mr.!

Worked great cheers 🍻

mine hasnt broken in a flat manner. gonna try this anyway. good vid

I did this method not even seen this video, works well

It work perfect, thanks and I did subscribe to your channel.

HOLY $HIT I LOVE YOU!!! THIS LITERALLY SAVED MY ASS.

Yes ! J'ai pris cette méthode et c'est super et simple et marche super bien

Yes it worked first go ! Thankyou !

Best video Ever! Worked 4 me!

I thought I've seen it all ,good one.

Wow good tutorial👍

Going to try this tomorrow

Excelente idea! Gracias!

It's work!!! Bravo!

No no no. Must use left turn drill. I have had them spin out before using easyout. A right turn drill drives in further.

I going trying it but slightly smaller broken bolt. That one thing I dislike when tightening a Bolt it seems not to be tightening but all the of a sudden u hear a Tink.

Great job, bouna idea bravo.. bravo...

Good job thank you for sharing

Excelente idea 💡 👍 😍

Hell yes this video saved me big hubk of time and money. 66 Dollars to be exact. Bless

That looks like it will work for the problem I have. Thanks.

Good video friend, greetings from Mexico WEY

Getting broken bolts out is so satisfying

Great idea 👍

Very good. Malaco of Brazil

Finally what I was looking for but got no dam drill damit

You're a lifesaver, God bless you XD

Sweet jam

Very very good job

Good tactik dude

🙂 I can use this! THANKS!

I will try this on my brake caliper bolt that broke on my knuckle 😢 thank you very much

Não tô conseguindo tirar parafusos do compressor de ar direto ele nunca foi aberto e nunca teve manutenção e eu já espanei todos os parafusos de tanto tentar tirar porque eles estão bem emperrados que nem se me chamou. .alguém me da um dica que funciona

So cool. Now I know I'm not the only one who ends up with a off center hole.

Gracias,buen truco.

This is so smart

I need to fix my car but I can't stop grooving to the tune man !

Thank You so much. 👍🏼