Thank you so much for this video. I followed it tonight and swapped my tire out fairly easily. I would have never even attempted it without this video.

Just wanted to leave my appreciation. Struggled getting the tire off for a bit but managed to pop it off thanks to your guidence about the groove. Also managed to seat both beads with just a bike pump. I got lucky and only needed 40 PSI which was super nice. Thanks for the great guide!

Thanks a ton - just swapped my tire out, this was such a great tutorial. Saved myself $100 of having a local motorcycle shop do it for me. Nice to no longer be afraid of changing the tires on these bad boys!

I have watched 10 or so videos on how to do this. By far the best video. Everyone else makes it too complicated. Took me a little over 20 min. Thank you.

TFL tire change video showed me where to put my hands but gave no explanation. So when it didn’t work I was stumped until I watched your video. Thank you

As soon as my new tire comes from c&r this t8me im doing it myself thank you for this video!

Thanks for this tutorial. My Vega was all worn out after 1300 miles. I bought a Hoosier with tread. Your step by step instructions gave me the courage to attempt this. It was difficult to break the bead on the old tire. The main difficulty I had was the new tire would not seat on the valve side. It said not to exceed 40 psi when trying to seat the bead. In the end, I had to use oil and pump it to about 100 psi before it would seat. Scary, but I got it done. Thanks again 👍

best OW tire replacement tutorial... it's all about "the groove!" ... I also like how you taped and tucked the wire harness neatly in the hub while breaking the bead to avoid damaging the wires. I really appreciate your guidance. I feel confident that voiding my warranty will be worth the joy of riding on a FF Housier Whisper.

Thanks for this great video. This one is IMO the best I've seen. A person could use just this video and get it done.

Nice tutorial! I haven't had to replace my tire yet but this video gave me a little more confidence when I'm due. Thanks for putting this together!

On my 2nd tire change, thanks again for the video. Also waiting on my nosedive shirt :)

Best video on this... still took me forever, but next time will be cake

Awesome tutorial! I just received my 6" treaded Hoosier and was nervous about attempting this by myself but you made it look pretty painless! Thanks so much for sharing!

I finally got round to changing the tyre. You did make it look easy! Breaking the bead was the killer, one side was easy but the other wouldn't budge. Eventually resorted to a hammer and bolster and it popped out. I got it all back together and,,,,,,,, it didn't work. Just a twitch as it tried to start. I eventually traced it to one of the smaller round cables. When I first tried to remove the plug I unscrewed the wrong end (nearest the wheel) and must have broken one of the wires off the terminal. I re-soldered the wire and all seems well. I'm off out for a test ride, fingers crossed! Thanks for your help.

Thanks for the video. This was super helpful when I changed my tire and it is by far the best tire change video out there.

The BEST/SAFEST way to Get a New Tyre On with Less Pressure After cowering under the work bench and taking my new tyre up to a presumably sketchy 65psi and still not getting the the other bead to pop on (using dish soapy water) I realised that the round electric cord from my extension cable was thinner than the inner rim. So with the extension cord (not plugged in obviously) I slotted it in and round the half side of the tyre that the bead was further up on, then bingo this kept the tyre's bead more level letting the stubborn side pop up far more easily (at only 30psi). With the soapy water there peeling the round electrical cabe back out was super easy and then the seal pop finish slid up (now evenly) and popped on at less than 30psi.

Thanks dude! This was a super helpful tutorial. I'm getting ready to change my first wheel now and I I feel much more confident going into the project now

Awesome! You made changing the tire look so much easier with your techniques. Very thorough and helpful video! Thanks!

Great video, I used wood clamps to break the bead and it was easy.

Great video, I just changed my tire while watching your video. Perfect directions.👍

Sup Eric, finally going to try your tutorial out for the first 2020 wheel change of the season, thanks for making this look fun, easy to digest and pleasant. Way too many people try to make it seem like rocket science 🚀😂. Shout to Mcfly for linking me to your channel and ig, 🤙. Skate on, and float on

hey, thanx the simplicity in explanation, is what made your video a good reference point in change to my Hoosier tire..

Thanks for the video... other videos are missing the tip about the groove in the rim.

Thanks for a consice tutorial. Best I've seen. Now keen to try my FF Hoosier.

Thread-lock is our best friend.

I suspect you make it look much easier than it it is, top job though.

Great video! Thanks for sharing.

Good video. My tire did not come off that easy, what is surprising to me since the rims should always have the same size? My Hoosier was also not as soft as yours (FK compound)

super helpful - thank you! "use-the-groove"

Thank you for making easiest video. Should I need valve core remover? Because I don't have it at the moment.

Great video. Would’ve been nice to get a few closer looks at the plate covering positions but still good

one thing you did not mention, Hoosier is a race tire and they are made to be mounted a certain direction for the rubber to wear efficiently if they have an arrow on the the sidewall mount them in the tire rotation it indicates, if no arrow Mount then so the serial number on the tire is facing the left side of the board (picture it as a car, mount the serial numbers facing drivers side)

Sweet this helped me tremendously

thank you!!!!!!!!!!!!!!!!!!!!!!!!

Very great tuto thank you a lot

why spray with Windex at 6:03? is it just to help the tire slide on?

Great video thanks!

Great and concise vid. What’s the purpose of the slime? Is it necessary?

Very helpful!!!

Thanks for making this! Just to be clear... No inner-tube, correct? (Tubeless?)

Awesome Tutorial. Just curious I saw what looked like a tube of blue loctite. Did you use any on the bolts? I started to then stopped because I started to doubt which bolt went where.

Would there be a way to flip the tire without taking it off the rim? I wear my heel side a lot fast than my toe side. Is there an easy way to swap the side hubs or something... Great video

Great video! Will have to give this a try one day! How many miles did you get out of your tire?

Eric any chance you have the dimensions for the 4 rail axle bolts and thread? mine came stripped on one from the factory not aligning the bolt properly and need it fixed. thanks

Awesome tutorial, still confused on what the "bead" is and of i should be looking for that burst or pop of pressure you got when you reinflated it. Also i only have a manual pump, would it be good enough?

Perfect example of why to not to use fix it flat

I'm curious as to why would bother with that tire slime? I have always avoided that type of stuff as it never seems necessary and just makes a mess. I've always just used a thin coating of bead grease on the outer sealing edges to prevent the tire from being difficult to remove in the future.

Instead of kneeling over it and praying to the gods you're strong enough to break the seal, use a wood clamp!

I need to change my tire soon I’m looking into the more rounded shape like this. How’s the tire going for you? Does the tired ever rub against the board?

Do you know or I can buy the motor itself because mine burnt up after I modded my onewheel

Why did you remove the footpad? You don’t need to do that to get the wheel out right?

what does the slime do? and do you recommended?

Hey awesome video, I just received a Hoosier 6" treaded and want to do this myself. I was wondering what the purpose of the goo inside the tire is? Also, how do I remove that valve core?

What is the purpose of the green slime found on the motor? I would like to know :)

Two things im assuming but would love clarification: I assume u could also just fill the tire with slime AFTER you have reassembled the whole board back together? You would just have to take the valve core out again? I also assume this process would be about the same for a Onewheel+? Looks the same but mine isn't an XR

Do I have to remove the valve core to do this install? Could you post a link to where a tool like this can be bought?

Cant get the tire off. Can you make a video or share a link with more description to use that groove?

Does the newer tire hold more weight capacity than the older one?

Tools needed….screw drivers and Allen wrenches….pulls out some pliers lol

any reason not to use bead sealant instead of slime?

thanks¡

You have some strong fucking hands

I can't find the tire with size 11.0 × 6.0 - 6 But i found 11.0 × 5.5 - 6 11.0 × 7.1 - 6 11.0 × 8.0 -6 Can i use one of this size to onewheel+ xr ?

Where do I get that t-shirt?

Is it possible to set a tire bead with like a bike pump? I don't really have an air compressor readily available to me but I can find one.

I have a superior method. Step 1: Consider, for just a moment, doing this myself. Step 2: Yeah, screw that. Step 3: Pay someone else to do it.

I'm sure your wife appreciates using the new white towels to clean all the green gunk off the rim... You put another slick tire back onto the rim?

So wait, you don't NEED slime?

Do you have to do tire balancing after the replacement?

What is the PSI for the tire

Every tire shop I know uses soapy water not windex

You gotta get a small electric driver

No way that’s a new tire that you are putting on

2 half hours i am only at 4:26 grrrrrr

What was your torque value for the axle?

What does the slime do??

Man I cannot get my tire to seat for nothing

WTF is all of that slime? Does the Onewheel come with that shit?