OpenBuilds LEAD 1515 Electronics and Software (Using BlackBox)

Рет қаралды 54,768

Күн бұрын

Follow along with this comprehensive build video and learn how to assemble your electronics and configure your software for your LEAD 1515!
🛒Get yours here: openbuildspartstore.com/lead-...
📚Learn more here: www.openbuilds.com
Assembly Chapters:
0:00 - Intro
0:47 - Step 1: Wire Connector Assembly
7:00 - Step 2: Xtension Limit Switch Assembly
15:32 - Step 3: Labeling Wires
19:48 - Step 4: X Axis Drag Chain Assembly
27:41 - Step 5: Y Axis Drag Chain Assembly
32:13 - Step 6: Flexible Tubing Assembly
35:44 - Step 7: BlackBox and PSU Assembly
43:29 - Step 8: Wire Management
47:39 - Software and Machine Control

Пікірлер: 20

@fishinfever6465 3 жыл бұрын

Right on, completed the wiring process thanks to another helpful video... great work!

@Island.dweller 3 жыл бұрын

Just finished this step. 6 hours into the build so far. Just need a spindle!

@949Designs 3 жыл бұрын

Good job Matt! 🤙🏼

@OpenBuilds 3 жыл бұрын

Thank you! 👍

@Masis-dr5el 6 ай бұрын

Thanks to very detailed explaining ❤

@OpenBuilds 4 ай бұрын

Glad it was helpful!

@isaacr5794 3 жыл бұрын

How do you select the start location of each cut? You would want to do this to avoid cutting away the excess material that you are using to clamp your material down.

@thespaltydog1039 3 жыл бұрын

I noticed when mounting the y axis cable chain at the back of the machine the whole machine is lifted slightly on that corner. This is because the tee nut and the screw sticking through. Would this corner being slightly elevated have any impact on the accuracy?

@samuelk009 3 жыл бұрын

Does open builds have an extention kit for the sphinx

@OpenBuilds 3 жыл бұрын

Please reach out to contact@openbuildspartstore.com so we can further assist you.

@fenders9911 3 жыл бұрын

I use v-carve pro 10.5 and mach3 can I use open builds software with my machine

@OpenBuilds 3 жыл бұрын

You can use V-Carve or any cam software, but there is no need for Mach3 as OpenBuilds has a free easy to use control software called OpenBuilds CONTROL that will read your gcode and control your machine software.openbuilds.com/

@dr-makes 3 жыл бұрын

Hi! In March 2021, be careful with the wiring of the motor, I followed exactly your method, and the nema 23 high torque don't turn. I checked with a multimeter, and have to invert two wires. Thx for the video.

@Qui95Qui Ай бұрын

Hey Dr Makes, which 2 wires did you invert?

@mokhtarabdulwahab2510 3 жыл бұрын

What's about a machine 6' x 10 ', I hope to have a video showing its assembly and what's the cost?

@fathmi 3 жыл бұрын

Why using only 3 limit swithes, and not 6 ( 2 on each end of 3 axes) ?

@OpenBuilds 3 жыл бұрын

You can use 6, we just you three as a home position

@fathmi 3 жыл бұрын

@@OpenBuilds I have noticed blackbox can only add 3 limit switches.. what should I do if I decide to use 6 switches instead ?

@OpenBuilds 3 жыл бұрын

Yes you can have 6 limits just wire them in parallel and with the OpenBuilds Xtensions is super easy to do. - SIG on controller to SIG on switch 1 to SIG on switch 2 - V+ on controller to V+ on switch 1 to V+ on switch 2 - GND on controller to GND on switch 1 to GND on switch 2 Just like docs.openbuilds.com/doku.php?id=docs:blackbox:connect-xtension-limit but paralleling each wire to the second switch

@fathmi 3 жыл бұрын

@@OpenBuilds Thanks!