Ortur

Рет қаралды 10,273

Жыл бұрын

Hi, today I will engrave a photo of a Dodge Hell Cat SRT on to a 30x20cm mirror, then install it into light box fitted with 2.4m of full RGB LED's, all will be done using the Ortur laser master 3LE 10W machine, please if you fine this video to be of any use to you then please hit the LIKE & SUBSCRIBE button. #laser master 3
Thank you.
Please check out links below.
If you're interested in purchasing the Ortur laser master 3 LE engraver or software I use, please check out the links below.
Official Ortur Discount code:
OLM3 LE: 60FORLASER
Accessories: 10FORLASER
My Facebook page where you can see many examples of work done:
/ lightworkz.graphicdesign
• Laser Engraving
Ortur laser master 3 / laser master 3 LE:
ortur.net/products/ortur-lase...
Software that I would recommend:
ImagR: www.imag-r.com/
Lightburn: lightburnsoftware.com/
@ImagR-Laser @ORTUROFFICIAL @HouseOfLasers @LaserLivestream @LaserEngraving911 @orturnet
#laser #engraving #ortur #laserengraving #lasermarkingmachine #lasermaster3 #glassengraving #engravingmachine #orturlasermaster2 #glassengraving #gifts #engraving #engravingmachine #facebook #lasercutting #orturlasermaster2

Пікірлер: 20

@ltrick2387 Жыл бұрын

WOW! What a fantastic project!

@lightworkz61 Жыл бұрын

Hi and thanks ;)

@robertdutton6110 Жыл бұрын

Very well explained Thankyou.

@lightworkz61 Жыл бұрын

Thanks mate ;)

@William_Van_Landingham_III Жыл бұрын

Excellent work! Subbed.

@lightworkz61 Жыл бұрын

Hi & many thanks ;)

@lightworkz61 Жыл бұрын

Thank you ;)

@lles3D_Studio Жыл бұрын

sehr gut 👍👍

@lightworkz61 Жыл бұрын

Hi and thanks ;)

@SieliececeliaMuller-pg5km 7 ай бұрын

Dis is baie nice en goed gedoen

@lightworkz61 7 ай бұрын

Thank you ;)

@johndavis3894 2 ай бұрын

Excellent project. It's motivation for sure. Where did you get the mirror, and what specific mirror did you use?

@lightworkz61 2 ай бұрын

Hi & thanks ;) the mirror is just a standard cheap 30x20cm x 3mm thick mirror that I bought from Jumbo here in Cyprus, a pack of four was just €5, many thanks for the comment.

@jamesjacob2264 Жыл бұрын

Is it possible to get this perfectly done by using laser explorer instead of light burn, and get great results as this? (After processing the image through image-r) Or can you try on the other piece and we compare how far that basic app can take through a biginer since lightburn may look a bit complex. Thanks in advance It was a great work 👏

@lightworkz61 Жыл бұрын

Hi, sorry I can't use the app as I don't have access to WiFi in my work place, my PC has a direct fiber connection, sorry.

@josp60 Жыл бұрын

hi very beautiful! What laser settings did you use?

@lightworkz61 Жыл бұрын

Hi & Thanks ;) in Lightburn I used Speed=5000 Power=70 Dpi=317 Scan angle=0 Image processing in ImagR, I hope this helped, all my settings are shown in the vid ;) Thanks.

@josp60 Жыл бұрын

@@lightworkz61 thank you