Outboard Control Cables Installation - Jon Boat Side Console Conversion

No video

Outboard Control Cables Installation - Jon Boat Side Console Conversion - Part 2

Рет қаралды 41,936

Жыл бұрын

In this video I go through the entire process of installing & adjusting the wiring harness, throttle and shift cables for a new 2023 Yamaha F25 Outboard with controls. I go over how to install the throttle and shifter cable ends, adjust the linkage, install the cables to the control box and more. This easy to follow start to finish guide will walk you through setting up your own outboard's control cables and control box.
Jon Boat Side Console Conversion series:
Part 1 - Measuring for Control Cables
- • How To Measure Outboar...
Part 2 - Outboard Control Cables Installation
- • Outboard Control Cable...
Part 3 - Outboard Steering System Installation
- • Outboard Steering Syst...
Part 4 - Side Console Installation
- • Jon Boat Side Console ...
Part 5 - Side Mount Control Box Installation
- • Jon Boat Side Console ...
Follow me on Instagram: @MVBOutdoors
/ mvboutdoors
---Product Links*------
5" Vertical Transom Riser - amzn.to/41zkJi7
3m 5200 - amzn.to/3ZpSUqG
Yamaha 703 Control Box - amzn.to/3LtgUpl
YamaLube Grease - amzn.to/3JpsxLl
---Related Videos------
Mounting Outboard to Jack Plate Riser
-- • Jack Plate Outboard Ri...
How To Remove Jon Boat Bench Seat
-- • REMOVING JON BOAT BENC...
1648 Jon Boat Build Playlist
-- • 1648 Jon Boat To Bass ...
*Orders through the Amazon affiliate links above provide us with a small referral commission at no cost to you. Using affiliate links in no way affects our opinions expressed on this channel and serve as a method to help this channel grow while providing useful, relevant information.
------------
#jonboat #boating #fishing

Пікірлер: 32

@sethnowlin2 5 ай бұрын

can you share the part numbers of the yamaha parts you got for the conversion?

@mvboutdoors 5 ай бұрын

---Product Links*------ 5" Vertical Transom Riser - amzn.to/41zkJi7 3m 5200 - amzn.to/3ZpSUqG Yamaha 703 Control Box - amzn.to/3LtgUpl YamaLube Grease - amzn.to/3JpsxLl

@marekszymecki4454 3 күн бұрын

Witaj. Obejrzałem z zainteresowaniem trzy odcinki. Z zamontowania przekładni kierowniczej, montażu manetki gazu i montażu przewodów do silnika. Nie znam języka angielskiego, ale wszystko co robiłeś pilnie oglądałem. Wszystko jest teraz dla mnie jasne. Pozdrawiam z Polski. Marek

@mvboutdoors 3 күн бұрын

Cieszę się, że podobał Ci się film!

@PowerhouseOffroad Жыл бұрын

Looking good! I'll just be back here with my tiller if you need me mr. Fancy!

@valentinecherake3812 6 ай бұрын

Very interesting in doing this for my own boat also

@boatingsibbingandwandering3262 5 ай бұрын

Many Many thanks for this video. It was incredibly useful and very well explained. Just fitted a pair of cables to my Yam 75hp 2 stroke and it went very well thanks to your video :)

@mvboutdoors 5 ай бұрын

Awesome! I'm glad to help!

@tyronebrown9409 Жыл бұрын

My friend has the same boat, you killed this boat builded good luck you ⛵ .

@mvboutdoors Жыл бұрын

Thanks man!

@mvboutdoors Жыл бұрын

One step closer to getting out on the water!

@Inov8iveN8ive Ай бұрын

Hey just a heads up, all the bolt holes are cast aluminum, good idea to use hand tools and ratchets rather than impact drill. Could easily strip of crack the housing

@Oversoul225 2 ай бұрын

I'm watching your videos to get ideas to upfit my 1548, and need to convert my tiller 2015 F25 to remote. So, I stop watching your videos and start googling. I find what parts are needed to take the tiller off and convert that (I think I have them now anyway, most of the internet's replies to converting from one to other is sell the motor and buy one made for it from factory). I find the needed remote control (703) and search for installation to get an idea on other parts.... And Google brings me back to your build haha!

@mvboutdoors 2 ай бұрын

Haha, what a wonderful loop you've found yourself in. Good luck with the conversion!

@dzrrdz6834 3 ай бұрын

Thanks fpr making this vid!

@davehood1401 Жыл бұрын

Nicely explained bud

@CFD339 10 күн бұрын

Thanks for this. Mounted my new F25 yesterday and there's zero documentation with either the owners' manual or the 703 manual on the hookups at the motor side. Yamaha makes great motors and terrible doc. Between this and the Command Link gauge installation, it's a bit of a tetris game.

@mvboutdoors 10 күн бұрын

Yeah I noticed the same thing when I went to install this, couldn't find any info on it online. Glad it was helpful!

@saeedkobiakov8351 Жыл бұрын

Hello, thanks for the videos!!! so i m doing the same conversion from tiller to wheel and i m having problem to find that little throttle cable kit that i need to mount first in order to connect the cable itself . Do you have the part # for it? it has like 5-7 pieces in it.

@mikep3186 Жыл бұрын

I have the same 703 to a 9.9.. when I shift forward or backwards.. there's excess movement in the 703 controller before it will increase or decrease speed.. how do you adjust the cable so it responds right away instead of having to go through dead space? Thanks!

@OtterLakeFlutes 6 ай бұрын

So I have the whole, thick, multi-pin electrical wiring cable and harness/plug hooked up to the motor and the motor hooked up to the battery. But what are the wires still sticking out of the Yamaha 703 Clone-trol box? They are capped off, red, greenish blue, yellow, and black. Dangling. Hopefully redundant, to be tucked away? Don't tell me I have to, also, hook these up to something... it looks like I see them tucked up (capped off, unused) inside your example 703.

@mvboutdoors 6 ай бұрын

They are for gauges, nothing you need to hook up I just tucked them away

@ibonigartua4719 4 ай бұрын

Hola buenos dias MVB 2:45 de que metrica son los circlip??

@mvboutdoors 4 ай бұрын

Sorry I dont know

@OtterLakeFlutes 7 ай бұрын

THANK you.. best videos on here by far,, about this... unfortunately my new yamaha F20 4-cycle does not possess the plate yours had with the stabilizer ridges for the groove(s) in the throttle/shift cables(s) to stay put. Nor is there shapes inside like other examples. Maybe it just uses the spots in that big bracket that holds everything... a little weird ; I wish I had the $90 tech manual.. I hope I can get it free digitally for dropping 5K in a new motor etc.

@mvboutdoors 7 ай бұрын

Yeah looking at pictures online it looks like there is no support bracket for the cables/wiring it just routes through the rubber plug.

@OtterLakeFlutes 7 ай бұрын

@@mvboutdoors I got weird and confused us both, I think I have the same setup you do (yay!), and I confused us by referring to a different video (not you, my bad) with a removable plate neither of us has, that , when mounted, sticks into the engine housing and grabs the cables inside there (larger motors no doubt) ... I do, indeed, have the ouside bracket you have, and I just now got the cables seated nicely in them. I see those pics without the cables supports online, too, but luckily mine does (maybe that's the tiller version where the shift cable still goes in but the throttle hole is un-cut and routed elsewhere). Now I need to look at those nuts on the threaded portion of the cables and understand how it is going to actually adjust anything (my head's not wrapped around that yet) ... err, wait.. maybe the cable routinely withdraws all the way past and into the threaded portion, so hitting the nut would stop it? Otherwise I'm not seeing what the nut you call a lock nut adjusts anything... Thanks again for the best video by far; I'll get it thanks to you and no thanks to Yamaha not yet mailing my serial number card which is seemingly when they enter the serial into the website so I can access any literature available (probably just the same, light operation manual, not the tech manual).

@mvboutdoors 7 ай бұрын

@@OtterLakeFlutes glad I could help, it's definitely a learning experience but so much better to do it yourself that way you can easily make adjustments on your own knowing how it all works.