✨Oxana✨ Thank you a million times over…. For sharing these absolutely wonderful idea’s! You are so kind! Greatly appreciated!
@sandmaker Жыл бұрын
A great tip. I'll bet lots of folks do it the other way. Have fun! 😷⚒
@dianeb7438 Жыл бұрын
Great tutorial. Thank you❤️
@tracysouthworth6145 Жыл бұрын
Learned something new! Thank you
@user-pd7il3xz5j Жыл бұрын
clear explanation, thank you.
@starr613 Жыл бұрын
These little tips r awesome ❤❤❤❤
@goddessgem84406 ай бұрын
Thank you!! ❤
@PhoenixCreationsKaTyJs Жыл бұрын
Wish companies would do that too lol loads I buy they are points one side and flush the other!! ❤❤😊😊
@daniaann Жыл бұрын
❤thanks
@cecelong8283 Жыл бұрын
Thank you so much!!
@barbaradavis8691 Жыл бұрын
😮😮😮😮😮 Omg..i just learned something new.. Dummy...all the video's and not one on how to correctly make a jump ring... THANK YOU VERY MUCH....... 🎉
@dawnsdesigns1 Жыл бұрын
Thank you for teaching me so much.
@OxanaCrafts Жыл бұрын
You are so welcome!
@wendyrock4260 Жыл бұрын
Wow thanks
@tammygurl64 Жыл бұрын
I ❤ all your tutorials! This is absolutely great if you're making a minimal amount of jump rings. I bought some cutters that are "supposed" to cut flat on both sides but are difficult to use to cut multiples because they tilt when cutting. I also bought jump ring pliers to use with my saw and that was a waste of money. It was easier to cut them with my saw at my bench pin. Thanks for all the help you give everyone. Cheers!🙂
@psychodrama15 Жыл бұрын
Thank you!! I brought a jump ring tool, but I don’t know What size gauge is best.
@jullesteach Жыл бұрын
can you recommend cutters that make a flat cut
@OxanaCrafts Жыл бұрын
most wire cutters make a flat cut on one side and a "pinched" cut on the other. The pliers I am using in this video are Swanstrom brand, before these I was using Xuron brand and they work the same way
@jullesteach Жыл бұрын
@@OxanaCrafts is double flush better
@nature-me4ow Жыл бұрын
Thank you so much for this video. I cannot find anything about how to harden jump rings by hammering them. Can you suggest a site or a way to do this?
@OxanaCrafts Жыл бұрын
I use a chasing hammer and an iron block(to do it on). I just place the jump ring down and hammer it with the flat side of the chasing hammer. I will try to make video soon.
@ginac73310 күн бұрын
Thank you... brilliant!! 🙋♀️💙✝️🇺🇸
@sophiaansley-palmer3406 ай бұрын
OMG thank you so much
@sherryhibbard55082 күн бұрын
Where do you get that tool to bend the Jump ring?
@user-xn3ie8lo5s9 ай бұрын
Thank you, I needed to know this!!
@OxanaCrafts9 ай бұрын
You are so welcome!
@janet584 ай бұрын
I make a lot at one time Their always flat, if there cut right.
@phyllistinetinker90767 ай бұрын
Thank you
@midnightbel Жыл бұрын
What guage and firmness do you usually use for jump rings?
@rzrbcks25 Жыл бұрын
I usually use 18 gauge half hard.
@OxanaCrafts Жыл бұрын
I like 18 gauge, but I don't have half hard so that's why I hammer it
@syzygy4365 Жыл бұрын
@@OxanaCrafts thank you so much! I could seriously hug you right now. ❤
@updownstate Жыл бұрын
Useful news, t y.
@OxanaCrafts Жыл бұрын
My pleasure!
@keenapearce2872 Жыл бұрын
I bought a bunch of jump rings in all different colors went to make a chain and their all like the first one you said not to do 🤦🏽♀️
@apt.144 Жыл бұрын
How do i know if i should get soft, full hard or half hard? I want to make small 3mm 22g jump rings.
@OxanaCrafts Жыл бұрын
Half hard typically works well for jump rings, but I have not tried full hard
@apt.144 Жыл бұрын
@@OxanaCrafts thank you for replying I appreciate it
@gstunna26 Жыл бұрын
I love how detailed and perfectly explained your videos are.
@OxanaCrafts Жыл бұрын
Thank you!
@susiebenson11 ай бұрын
What size copper wire ?
@OxanaCrafts11 ай бұрын
You can do it with all different sizes, for this one I used 20 gauge
@mawi117210 ай бұрын
❤❤❤❤❤🎉🎉🎉🎉🎉🎉❤❤❤❤❤❤🎉🎉🎉🎉🎉😊😊😊😊
@chuckyDLuffy5 ай бұрын
hello! i have a question what does hammering do? how does it make it stronger?
@OxanaCrafts5 ай бұрын
yes it makes the metal harder
@MrJaycob3102 ай бұрын
What are your pliers called??
@OxanaCrafts2 ай бұрын
They are Swanstrom brand
@ArtisanUntamed Жыл бұрын
There is a quicker way
@OxanaCrafts Жыл бұрын
if you have a jewelers saw that would be a quick way to make multiple jump rings