P2015 Clogged Or Disconnected Swirl Flaps On Your Volvo 2.4L D5? XC90 XC70 XC60 V70V50 S80 S60 S40

Рет қаралды 7,815

6 ай бұрын

Link to purchase product: x8r.co.uk/swirl-flap-delete-k...
Symptoms of Fault
Check engine light illuminated or flashing, rough idle, decreased fuel economy, reduced acceleration, increased fuel consumption, car going into limp mode, control arm disconnected from intake manifold
The Fault
Carbon build-up causes the swirl flaps to not work efficiently
The intake manifolds on the Volvo 2.4L diesel engines clog up with carbon build-up which causes the swirl flap arm to disconnect from the intake manifold or completely seize, causing an array of issues such as engine lights, limp mode, rough idle and all the other symptoms as listed above.
The Solution
Install the X8R swirl flap blanking kit to prevent carbon build-up and vastly improve airflow
Our X8R swirl flap blanking kit completely removes the swirl flaps and the arm to remove the possibility of the fault occurring again in the future. The removal of the swirl flaps drastically increases the airflow to the engine and improves performance and fuel economy.
The X8R blanks are made from fibre glass reinforced plastic, making them more durable than other swirl flap blanks on the market.
Vehicles Affected
Volvo vehicles with 2.4L diesel engines:
C30 2006-2012 D5 T9
C70 2006-2010 T8 T9 T13
S40 2004-2010 T8 T9 T13
S60 2001-2010 D5 T4 T5 T7
S80 2007-2012 D5 AWD T4 T10
V50 2007-2011 T9
V70 2000-2009 D5 T2 T4 T5 T7
XC60 2008-2011 D5 AWD T4 T14
XC70 2007-2010 D5 AWD T4
XC90 2005-2015 D3 D5 AWD
Associated part numbers:
3121646, 30777650, 30713459, 31216460
You Will Receive
10 x Swirl flap blanks
5 x Injector copper washers
1 x Intake manifold gasket
10 x Threaded red caps
10 x Small round caps
5 x Large round caps

Пікірлер: 20

@grahameleggett786 3 ай бұрын

Hi, I fitted the kit to my xc 70 d5, 2006, ( euro 4) I took my time, found the kit excellent value, and and profetional, n/b pay special attention to the injector, protection, , and clean up the injector seating ports with, air intake cleaner, and clean rag on a long screw driver, ensuring, injector seats are clean, I have exspireanced, no codes at all, sw/ flap actuator still in place, power is good, economy, is good as well, at the same time I have replaced the turbo actuator ( electronic) as this was not operating as it should and was getting codes stating turbo boost to high, turbo boost to low, the swirl flaps cause a build up of soot, and I feel it will run cleaner, internally without them, p. S prior to placing, swirl flap deletes, clean up the area with, carb cleaner/ engine degrease on a rag, I hope this is of help to any interested party's 🤗👌

@mattybarmby2662 2 ай бұрын

Fitted this kit today, good kit has worked for me. my actuator arm broke, my swirlflaps was stuck shut the car felt very restricted would go in limp mode everytime i reached 3k revs, and my mpg was very poor, since using this kit my car feels like a rocket compared to before and my mpg has doubled, i think it depends on what angle ur swirl flaps was stuck at to how much of a improvement this will make for your car but for me where the flaps was fully closed and clogged with years worth of crap it has done wonders for my car. Would deffo recommend

@X8RLtdUK 2 ай бұрын

Thank you so much for the amazing review and helpful comments on our video! Certainly very much appreciated! If you wouldn't mind leaving us a Google review we would be very grateful: g.page/r/CUq3bqyGoDaTEB0/review

@robsterlikesRonPaul Ай бұрын

Matt, this sounds like my problem... I have a 2006 V70 2.4d and the Engine System Service Required message is on... Also the car drives fine but as soon as it hits 3000 revs it seems to get restricted, like a limp mode... Is this what you're describing too? I'm not mechanically inclined but car is booked into garage... I was wondering how much you think I'm gonna be looking at to pay for this Swirl Flap replacement??

@phyrros1 Ай бұрын

So, what is the downside of removing the swirl flaps? There must be reason Volvo engineers put them in in the first place?

@X8RLtdUK 26 күн бұрын

I found an interesting article which explains swirl flap removal in-depth, with negatives being listed at the bottom, which you can see there are few: www.yorkshiredpfcentre.com/swirl-flap-removal#:~:text=The%20process%20for%20removing%20the,the%20flaps%20left%20in%20place.

@magee26 2 ай бұрын

HI, i've got a 2013 XC70 D5... does anyone know about its manifold and swirl flaps? I'm having trouble finding any information. Are the swirl flaps built into mani? thanks

@robsterlikesRonPaul Ай бұрын

Hello... I have a V70 2.4d from 2006... Can anyone give me a rough idea of the cost a garage will roughly charge for replacing these Swirl Flaps??

@phyrros1 Ай бұрын

In Europe Volvo repair shops charge around 1200€ for the repair

@k1leon 4 ай бұрын

Will i get error code if i use this kit?

@X8RLtdUK 4 ай бұрын

You shouldn't as the rod actuator motor will continue to work as normal.

@gheorghinacov6008 3 ай бұрын

@@X8RLtdUK It will give error since the motor will feel absolutely no mechanical resistance whatsoever, thus there will be the broken swirl arm error

@grahameleggett786 3 ай бұрын

No.. If you leave actuator in place.., if the swirl flaps were to be connected, and in normal opporational condition, there would be no restriction anyhow, the main problem would appear to be, that the throw of the actuator and arm is greater than the travel of the swirl flap connector pivot, resulting in the socket getting worn and the connector rod disengagement, so in my consideration, save any future grief, and fitt a delete kit 😊👌( no code for swirl flap, well not on my euro 4 d5 2006)

@X8RLtdUK 3 ай бұрын

@@gheorghinacov6008 it didn't give an error on our vehicle. There's no electronic sensors on the original arm so no warning code.

@richardwhiting3216 3 ай бұрын

Is there anyone in Essex who can help do this on my xc90. I am concerned with removing the injectors