Pace Inc. Soldering SMD J lead PLCC, Sockets w/Hot Air &Mini Wave Soldering tip

Рет қаралды 17,500

12 жыл бұрын

‪Pace Worldwide
For pro's only - Be the smartest SMD kid on your block!
One click below and see the entire PACE product line. This terrific catalog page has images of each Pace station and clearly explains the power supplies , and corresponding hand pieces included with each model. Explanation of PACE's intelliheat and Sensa-Temp technology. Please view this pdf doc. catalog before going to the PACE home page.
Pace makes the best PCB rework and repair products in the world right here in the U.S.
Pace is a certified IPC training school.
Free! best practice process guides for your convenience are on the site.
www.paceworldwide.com/sites/d...

Пікірлер: 36

@OliverONeill 11 жыл бұрын

You make this look so easy. You obviously show your skill very well in this video. Thanks for creating this.

@MrMarcSiegel Жыл бұрын

Thank You. Sorry for the late response. Best Marc Request

@hrz_nrd4511 5 жыл бұрын

You are the best I have seen so far!! I have tried already some of yours technic and damn right they work, I wish I could have seen your videos before I ruined my Xbox.

@MrMarcSiegel 3 жыл бұрын

Glad to help. Most people think my demo no longer applies to today's boards. Can you believe that! Best Marc

@magnusanemo103 6 жыл бұрын

3:03 Business in the front, party in the back! Thanks for sharing! I'm waiting for my hot air soldering gun to arrive to try this with PLCC chips and sockets.

@MrMarcSiegel 6 жыл бұрын

Good. remember preheating board with large ground plans. Preheat 150 f that should do it. always experiment on a trash board to find the right temps. Best Marc

@MarDan49 10 жыл бұрын

Jeszcze raz pragne podziekowac za wspaniale lekcje jakich udzielasz.Ciesze sie,ze "znalazlem" cie i moge poszerzac swe umiejetnosci i wiedze.Dziekuje.

@alaala97 10 жыл бұрын

O co chodzi?

@MarDan49 10 жыл бұрын

jacek lewandowicz Jacenty,otoz po specjalnym kursier i kilku egzaminach uzyskalem certyfikat (IPC-A-610) uprawniajacy mnie do zabudowywania komponentami elektronicznymi PCB czyli plyt z ukladami drukowanymi .Certyfikat ten pozwala mi na podejmowanie pracy na calym swiecie w tej czesci branzy elektronicznej i w zakresie klasy 1,2, i 3..Nie moge ,narazie,budowac PCB,ktore maja pracowac w kosmosie.To tak na wstepie.Natomiast moje podziekowanie skierowane bylo do Goscia,ktopry umiescil w You Tube filmy z szeregiem lekcji pozwalajacych na podniesienie kwalifikacji i zapoznanie sie z roznymi techniukami i technologiami lutowania komponentoiw.Tak to wyglada .Zalaczam pozdrowienia - Danilka.

@n4mwd 9 жыл бұрын

I'm not sure what you said, but I think it was a really good video too. I'm thinking about deigning a board with some of these parts and now I'm a little more confident. Marc, thanks for a great video.

@MrMarcSiegel 8 жыл бұрын

+n4mwd You are welcome n4mwd. Best Marc

@erhandemir90 5 жыл бұрын

Beautiful work sir

@MrMarcSiegel 3 жыл бұрын

Thank you Sir,Best Marc

@Ty_ThatGuy 11 жыл бұрын

You have restored my hope indoing SMD rework. I've been redoing PS3 and Xbox 360 motherboards and sometimes the smd's and chip capacitors have knocked loose/off during BGA / GPU removal which results in the system not working when reflowing and reassembly of the units. I just bought some solder paste so that if they come loose again, I can properly reattach the pieces. Thanks.

@MrMarcSiegel Жыл бұрын

Thank You. Sorry for the late response. Best Marc

@Bylga 8 жыл бұрын

Awesome video!

@MrMarcSiegel 8 жыл бұрын

+Bylga Thank you very much. Marc

@qbitsday3438 2 жыл бұрын

Excellent ! watching this Day 21MAY22 a Saturday .

@MrMarcSiegel 2 жыл бұрын

Thank you much. Best Marc

@orbita1 8 жыл бұрын

The speed at which you aligned that tqfp was incredible. i find that to be the most difficult state.

@MrMarcSiegel 8 жыл бұрын

+orbita1 Thanks for the complimentry note. Best Marc

@Ne3s23p2 6 жыл бұрын

0:30 Why break the shield ? It adds stiffness to the socket and prevents it from warping. I have successfully soldered a couple PLCC32 sockets without altering them, with very limited plastic burns, and could have not touched plastic areas at all with a video microscope.

@MrMarcSiegel Жыл бұрын

Could be my mistake. Thanks

@DalviqCash 2 жыл бұрын

Useful info thanks the question is was the original video really show with or edited on what seems to be an analog device either a camcorder or vcr or did you add the retro effects in post? The head switching noise on the bottom looks too legit to be successfully faked so I tend to believe the work was indeed don on some tape base system which begs the question why would you stick to the tape workflow in 21st century?

@MrMarcSiegel 2 жыл бұрын

Done on 16mm.

@MarDan49 8 жыл бұрын

Than you!

@MrMarcSiegel 8 жыл бұрын

+Marek Danilowicz You are welcome. Have a better one. Best Marc

@Master1782 4 жыл бұрын

Where can I buy a solder tip like the one you’re using for IC. I’m using Face in the company but they don’t have that kind of solder tip.

@MrMarcSiegel 3 жыл бұрын

Conical tip from Paceworldwide

@dibraniuk Жыл бұрын

I'm currently having trouble soldering smd pin headers any tips would be much appreciated and by the way thank you for the grat pace videos

@MrMarcSiegel Жыл бұрын

Thank you very much.

@MrMarcSiegel Жыл бұрын

Thanks very much I would Google pace worldwide

@patriram 12 жыл бұрын

Hi.... I bought a MTB-301 station... and I want to buy a microscope, but I am confused, I would like to know what eyepiece and objective size I need to work mainly with phones and with PC board...(mainly with phones). Now I am looking and SZ6045 SZ4045 SZ1145 OLYMPUS... and the have eyepiece 10X 20X 30X 40X and objective 0.5 1.5 and 2.0 If you can help me I would appreciate

@MrMarcSiegel Жыл бұрын

10x Thank You. Sorry for the late response. Best Marc