Painting a Bike With Spray Paint: Vintage Bike Restoration the 1987 Univega

No video

Painting a Bike With Spray Paint: Vintage Bike Restoration the 1987 Univega

Рет қаралды 65,763

2 жыл бұрын

#bikerestoration #bike #vintage
Thanks for watching:
I hope you enjoyed this and will come back for more.
Products used: buy them here and help out the channel:
Montana Cans:
Deep sea: amzn.to/3sNARxj
Pool: amzn.to/35ViBsz
Yolk: amzn.to/3sKWzll
Metal primer: amzn.to/3sLCJGJ
2k clear coat: amzn.to/3tBl0B5
Sand paper:
220-400g: amzn.to/3IPGNv7
120-300g: amzn.to/3CqtQFS
Trail Maps: www.teespring.com/stores/trai...
Become a Member and Help Out My Channel: / @runbikemike
Follow Me @: www.RunBikeMike.com
Swag: www.teespring.com/stores/runb...
Patreon: / runbikemike
My Video Gear: runbikemike.wordpress.com/gea...
Popular Playlists:
Build Time Playlist: tinyurl.com/yas6qyz7
Walnut Springs Playlist: tinyurl.com/ybueuuqj
Running Playlist: tinyurl.com/y375vesw
All links are Amazon Affiliated Link or Insta360 Affiliated. No extra charge for you but by using them you help out the channel.

Пікірлер: 122

@erichall7563 5 күн бұрын

Very nice job! Older bikes deserve restoration.

@rogeliorodriguez8518 Жыл бұрын

The bicycle looks amazing! I 'am getting ready to paint mine so I am doing a bit of research. Thank you for the video.

@AsapEF 16 күн бұрын

Nice project!

@superbird7 2 жыл бұрын

So glad I found this! I found a 1983 Univega Nuovo Sport put out with the trash after someone’s garage clean out. Similar condition to yours.

@jimjohnstone8665 Жыл бұрын

whenever your flatting a finished coat to get rid of any imperfections its easier to use wet and dry and to add some soap to the water then use your various grades of compound ,t cut then final polish.

@johnnydoe66 2 жыл бұрын

The bike looks amazing, keep it up you will be giving Old Shovel some competition....looking forward to the finish

@RunBikeMike 2 жыл бұрын

Thanks John. I am having a lot of fun with this bike.

@pacreamer1 Жыл бұрын

Nice work dude! I'm riding Ragbrai on my 80's Univega Supra Sport this summer.

@MTBQandA 2 жыл бұрын

Love those colors you chose! They really work well with each other.

@tribestribes2555 11 ай бұрын

So very nice just to hear the tools working, and also the relaxing music in background. Great.

@colinwellman9480 11 ай бұрын

It looks really nice. My frame respray with rattle cans turned out OK but didn't last. In the end I had it stripped and powder coated (single colour) for about the same as the cost of all the cans and preparation materials. This was 5 years back and the finish is very durable.

@10OZDuster 9 ай бұрын

rattle cans are too diluted less than 15% paint the rest are propellant and thinner so it sprays out of the nozzle with minimal internal pressure thats why they dilute them. If you used 20 cans that would be equivalent to a regular paint spray thats why rattle cans are NOT the process for a "good" paint job for quick jobs to cover up bad/old/faded....yes it works but for a lasting beautiful paint job go for the real thing or in your case powder coat which is expensive but worth what you pay for as painting with spray cans ain't quick and easy.....since its so thin the waiting to dry between coats is too long and if your in a hurry you get orange peel its a waste of time and effort in my opinion if what someone wanted is a lasting paint job.

@stickmenkissarmy6907 Жыл бұрын

Super job on the bike...

@johnmclean8643 Жыл бұрын

I have 2 Univegas..These bikes have a great ride quality..You inspirer me to paint my 1985 Schwinn Tempo..Schwinn used Panasonic to build the frame for that model..I bought that bike new in 1985 and couldn’t part with it..Great job Mike 👍

@Engineer_Eric_59 Жыл бұрын

Thank you for posting. I have a mid 80's Trek road bike I need to restore and this was helpful.

@peterdrastrup Жыл бұрын

Absolutely stunning colors! Very nice done! And super brave you started wet sanding on the top tube. ❤‍🔥

@shaunmanning8698 Жыл бұрын

Well done fantastic job it was so video 10 times so good please watch this video fantastic I was so excited looking all different layers paint going

@fishermanmitch1 Жыл бұрын

when i painted my bumper on my truck, I was told to let the 2k sit in hot water prior to spraying. People swear it'll cut back on orange peel. My bumper turned out perfect. No wet-sanding required. I'm getting ready to custom paint some of my bicycles, so hopefully I'll have the same result.

@02biku95 7 ай бұрын

How beautiful!!! pool blue/navy color looks amazing ! (from Japan)

@BuffsVintageBikes Жыл бұрын

Turned out great, well done 👍🏼

@Frog_Creations Жыл бұрын

Well Done, Good Man

@randy1817 9 ай бұрын

Looks Good!! I like older bikes better than the new ones..

@robertklipstein5878 Жыл бұрын

i had the exact same bike...donated to a reuse center and i wish i hadn't

@vinaysoni2032 8 ай бұрын

Incredible paint job, looks so good!

@Nerdsplayingcards Жыл бұрын

Amazing resto paint job , great work , and yes Montana is the best paint

@andreasbergwall9437 4 ай бұрын

Love the colors!! Looks awesome. I'm not sure it's wise to was the internals of the frame with water.

@peterquest6406 2 жыл бұрын

Etoe has some good vids on painting frames.one on clear coating.

@ilikesnow Ай бұрын

I did a Univega 24" bmx cruiser with Matte 2K and it turned out awesome. You should definitely check out the matte spray. Great video man!

@VeloPettersen 10 ай бұрын

Wow! Really love how this turned out. Great work👊🏻 Enjoy watching your videos.

@TheLithGH Жыл бұрын

Ah, man... that Univega brings back good memories!! I had a blue "Viva Sport"? (I think it was called) as an early teen in the mid 80s. Loved that thing!! Thanks for postig! I have my fathers mid 80s Pinarello that I'm looking to restore, so appreciate your time in making this video!

@snbsmtb 2 жыл бұрын

Great video Bro!! The bike looks soo amazing!!

@karimtv2 2 ай бұрын

Thanks for sharing this video

@mariocavuoto4894 11 ай бұрын

If taking off decals a hot air gun, I did my 1987 Tange Infinity frame about a month ago, used paint stripper to a point and then a wire wheel on angle grinder lightly took the rest off in 5 min and works well around the curves and joint areas. Wax and grease remover before painting the most important thing. Three light coats of undercoat, let dry for a day then 3 top coats drying for a day again followed by 2-3 clear coats.

@josefkapelj3842 Жыл бұрын

Man you are the Best .wish you lived in Australia I'd 160%Get you to restore some of my bicycles. Keep up the great work 👍

@RunBikeMike Жыл бұрын

Thanks 😊

@Rockrider520 2 жыл бұрын

Amazing 👏💯

@RunBikeMike 2 жыл бұрын

Thanks 😊

@marcdelente2456 Жыл бұрын

formidable mais je me sent complètement incapable de faire la même chose . Vous ête formidable bravo.

@theretrobikeshed3392 Жыл бұрын

What an awsome job youve done 👍 just subbed in 👌

@techguy9023 11 ай бұрын

You could do the sanding prep and check if a body shop could paint it when they were doing a car.

@MrEpsilonZero 8 ай бұрын

WOW so much patience. I would just paint single colour primer then colour.

@pierrex3226 Жыл бұрын

Very nice. 2K clear coat if breathed will REALLY Fs up your lungs apparently. If inside, wear the right kind of mask (for solvents, not just any mask). Masking question. How do you get a clean cut between 2 colours?

@troytaylor1913 5 ай бұрын

I painted an aluminum frame with rattle-can Rusto-oleum Automotive acid etching primer. I thought the acid etching primer took too long to dry. It was sandable but it wasn't really dry for about 2 weeks. After it dried the was stuck on good and chip-resistant. I tested it on some handlebars. I got good results but I don't like to wait that long. I would rather mix acid etching epoxy primer in a spray gun.

@troytaylor1913 5 ай бұрын

I dropped the handlebars on concrete 3 times before the paint chipped. The primer under it didn't chip. It's good stuff if you like to wait.

@troytaylor1913 5 ай бұрын

I used, used brake fluid to remove the old paint. I just keep brushing it on and keep it soaked for about a week. The paint comes off to the bare metal easily with a brass brush soap and water.

@jwrobin21 Жыл бұрын

You only get ORANGE PEEL if you put the coat on too think, too quick and do not give it time to semi dry. A good trick is a scrap car (but with doors and windows), take the seats out and then on a hot summers day, spray the frame inside which will cook the paint nicely. Give it a light coat every time the paint feels tacky to the touch.

@rachaelrobson981 Жыл бұрын

Hi! Can I ask the name of the music that plays through this video? Thanks!

@malcolmjgen Жыл бұрын

Beautiful work!! Well done!! What was the time line between adding the primer once you got the paint off to spray painting with colour and then to the clear coat??

@RunBikeMike Жыл бұрын

If I remember correctly it was a few hours between coats of paint then I waited over a day I believe before the clear coat.

@davidhollinger2987 Жыл бұрын

Enjoyed watching and learning from your process. I have a Univega Via DeOro I am about to work on. Did you create the rub on decals or purchase them?

@RunBikeMike Жыл бұрын

I created them on a Cricut

@albertohart5334 9 ай бұрын

Any tips for doing this on a bike with a threaded stem? Should I take the press fitted bearings off? (It would then be very tough to get them back on) or should I tape over them and paint ?

@mckaywilliams2787 Жыл бұрын

What did you use after realizing hand sanding wouldn't be enough? Running into the same problem right now but don't want to strip too much metal away with certain power tools.

@RunBikeMike Жыл бұрын

Orbital sander it made fast work.

@mckaywilliams6479 Жыл бұрын

Sweet, thank you! what grit on the orbital?

@RunBikeMike Жыл бұрын

60 and 80 then used a high grit by hand to get rid of any scratches.

@johnpeters1728 Жыл бұрын

Very nice video. I am planning to paint my vintage french bike as well. I would like to know how did you get those custom stickers printed that you used for the logos ?

@RunBikeMike Жыл бұрын

I designed them and cut them out on a Cricut.

@stevenlarrea9253 4 күн бұрын

Awesome! inspired me to paint my 50s schwinn varsity. How did you get those stickers/vinyls made?

@RunBikeMike 4 күн бұрын

I made them with my daughters Cricut

@jackcooper4889 Жыл бұрын

Awesome video. I want to repaint my old 8500 Trek. How do you make or where do you get your stencils? In my opinion the job isn’t complete without them. Thanks.

@RunBikeMike Жыл бұрын

I made them on my computer then cut them with a Cricut.

@jackcooper4889 Жыл бұрын

@@RunBikeMike awesome I found some videos on how it works. Thank you 👊🏻

@longlaketech 2 жыл бұрын

Enjoyed the video. The restoration is just beautiful. How does she ride?

@RunBikeMike 2 жыл бұрын

I am so surprised at how well it rode. Next week I should have the finish build video up.

@TheLithGH 11 ай бұрын

When you were done, and the paint had time to dry and cure, did you find the paint to still be soft and chip, or scrape easily when, say leaning it against a wall or a pole (if locking it to a bike post outdoors, etc)

@RunBikeMike 11 ай бұрын

It wasn’t as strong as car paint. I think if I did more clear it would have been.

@TheLithGH 11 ай бұрын

@@RunBikeMike Good to know. Thanks!

@markbowden1976 10 ай бұрын

Mate you have done incredible... Where and how did you get those little personal decal stencil stickers from?

@RunBikeMike 10 ай бұрын

Thank you. I created the decals myself on my Cricut.

@benjaminrasmussen4750 Жыл бұрын

Is it a bad idea to buy paint remover chemical and then strip it down to bare metal, then prime and then paint?

@RunBikeMike Жыл бұрын

That can work but you will want to get aircraft grade as the stuff you can buy at Lowe’s won’t do anything to bike paint. Just make sure to clean the frame really well before you prime it.

@arsnpstn6913 Жыл бұрын

Where did you get a decals?

@RunBikeMike Жыл бұрын

I made them with a cricut.

@DafirulAhyarDavid 21 күн бұрын

Hi, I wonder how did you make that new UNIVEGA stickers...

@RunBikeMike 20 күн бұрын

I used a cricut to make them.

@leonfeddema7998 Жыл бұрын

Really amazing !! Where did you get those decals??

@RunBikeMike Жыл бұрын

I made them and cut them out on a Cricut.

@leonfeddema7998 Жыл бұрын

Cool! The letters Univega are great. Do you have more of those ?

@AlphaProductions_ Ай бұрын

Don't you have to sand down your primer a bit before adding the color?

@ericdavis7532 Жыл бұрын

I sanded mine to metal, and decided to clear it

@igorzelinsky4521 5 ай бұрын

Your decal stickers didn't leave any glue on the frame? Ours did, now thinking how to remove it carefully.

@RunBikeMike 5 ай бұрын

No, I used the removable Cricut brand vinyl.

@neilparnell5712 11 ай бұрын

Love the colour scheme, but why didn't you fill the small dent in the top tube seen at around 14:50 ? seems an oversight after all the effort put in.

@RunBikeMike 11 ай бұрын

I wish I would have. But at the time I wasn’t super confident I could fill it correctly. I should have tried.

@neilparnell5712 11 ай бұрын

@@RunBikeMikeModest honesty - love it.

@MichaelMoore-iw8iw Жыл бұрын

Nice video, where did you get the decals from?

@RunBikeMike Жыл бұрын

I got images off the internet then cleaned them up in photoshop. Then used a Cricut to cut them out in vinyl.

@omarzarka 9 ай бұрын

Beautiful! Did you custom print the stickers?

@RunBikeMike 9 ай бұрын

Yes I did make them myself.

@timothyswan3483 Жыл бұрын

Where did you get the stencils?

@RunBikeMike Жыл бұрын

I made them

@timothyswan3483 Жыл бұрын

@@RunBikeMike nice. Would love to be able to do that. Any chance you’d make a video on that?

@Granolaboy1 Жыл бұрын

Why didn’t you show it complete with wheels, handle bars, etc, pedals, etc?

@RunBikeMike Жыл бұрын

This is a series. There are 3 videos in that series. Here is a link to the playlist with them in there. kzfaq.info/sun/PLALZVHdIBx98kAycxL4pCh-UTfM0iGyBU

@ryan_leach Жыл бұрын

Why not bondo that little dent on the frame

@RunBikeMike Жыл бұрын

I wish I would have

@Handletaken4 10 ай бұрын

The fork was threaded and stem threadless?

@RunBikeMike 10 ай бұрын

It is a Quill stem adapter

@simonirvine1628 11 ай бұрын

Paint stripper or an acid bath...

@ahenders81 Жыл бұрын

You were going to leave the original chromoly decal I believe. Too much trouble to work around?

@RunBikeMike Жыл бұрын

Yeah it was going to be to hard to save it

@riverthecat 11 ай бұрын

Dang..is every bike medium/ large and extra large...cant find a decent project bike small...aggghhh..!

@jayedannholmes6367 Жыл бұрын

Just use a hair dryer on hi and they will peel right off

@josejn2007 11 ай бұрын

At this point, after a little over a year of this video, if the bike was used, it must surely be chipped in several places.

@Tarmaccyclocross 11 ай бұрын

I couldn’t be bothered doing all that work on a frame that was crap when it was new

@RunBikeMike 11 ай бұрын

Ok thanks for taking the time to comment that

@josejn2007 11 ай бұрын

Spray painting is wasting time and money. No matter how well the surface is prepared and good products are used, in a year or a little more it will begin to peel. Just have a professional do it with baked paint or epoxy. You will not regret. It's my experience on several bikes I've painted.

@lukealexander3639 3 ай бұрын

Not if you use 2k clearcoat

@petergiourelas3753 3 ай бұрын

Don't agree

@josejn2007 3 ай бұрын

@@petergiourelas3753 Perhaps you are not using your bike enough. The bike won't peel while hanging.

@amboroverdecillo8101 11 ай бұрын

Why did you cut and destroy perfectly good vintage brake cables and probably also the chain too!? It goes against the whole idea and ethos of restoration.

@RunBikeMike 11 ай бұрын

Did you see them?

@kr5746 8 ай бұрын

you really don't need music :/

@RunBikeMike 8 ай бұрын

@bogdanpetrica Жыл бұрын

The lugs are not clean

@bogdanpetrica Жыл бұрын

Because is almost impossible to clean the lugs with sandpaper and wirebrush I personally used a chemical paint remover

@bogdanpetrica 11 ай бұрын

Yes, I know is impossible to clean the lugs with sandpaper and brush, the other option is sandblasting. Personally I used the chemical paint remover and it worked very well for me.