Get 60% off your 1st HelloFresh box + 20% off the next 2 months + free gifts! Use code ADAM2024 : www.hellofresh.co.uk/ADAM2024

Not sure I could bring myself to leaving that garage.. I am sure it's for a good reason, all the best Adam.

the welding looks like the shroud is full of spatter , theres not much gas clearance on smaller/hobby welders so a few bits of spatter will foul up the gas flow . a good tip would be check your shroud is clean and your tip is clean before you start a weld , turn your wire speed down a touch aswell your using to much wire just go for a spot weld not a full weld or stitch weld and you wont get the raised weld like a slug, the primer wont help for a good weld either , i would buy a can of anti-spatter and apply a dusting on the areas before you start as it helps a lot and makes cleaning easier by simply using a small decorating scraper ...check your gas is flowing by holding the torch by your ear aswell but always point the wire away from your head when pressing the trigger so it does not stab you . oh and always start a weld with a cleanly cut wire by using a pair of side cutting pliers . and you will get the pest finish every time mate . i use flux wire on my mig at home its much easier and requires no gas to weld with so its less hassle on smaller jobs .

Well done again Adam, these videos give us DIY'ers plenty of inspiration and incentive to tackle many jobs we hate or put off. Happy St.Patrick's day from Dublin. CheeRS

Raptor is not the right thing to put on the bottom of a car especially on top of old stone chip/sealer, raptor is a hard none flexable coating originally made for truck beds if theres any movement underneath it will crack a peal off, Gravitex is the correct product to use for this job.

I recomend Bilt Hamber products for rust prevention/ cure. Top quality.

I’m not jealous…much! Get out there and enjoy her when the sun comes! Cheers for the video Adam

I know you said this is temporary. But man you’ve made a properly nice job of it under there. Nicely done 👍🏻

I used raptor on my mantas in 2016. It’s still good to this day. Fantastic stuff.

Another fantastic video Adam. You're doing a great job on the escort, definitely get it out and about for the summer. I just used stonechip under my Manta 400 and i regret now not using Raptor. Next winters project sorted. Hope you get sorted with a garage, thats a lovely man cave you have at the moment it'll be hard leave it!!

Well done Adam it’s coming along nicely mate 👍👍👍

Best of luck with house move mate. Hope new workshop works out for ya! 👍🏻

On the angle grinder, I held a piece of metal.inbetween my legs, grinder slipped, stuck 2, 2 inches, gashes in both legs, 2 mm away from an artery. I'm lucky with 15 stitches and an awesome pair of scars.

Looks really good adam nice job can't believe your giving up your garage don't think I could give mine up

stand the aerosol in warm water for a few minutes. shakes up easier and increases pressure of spray Adam.

Your welding will only improve over time... there's wire speed, wire thickness, heat range etc.... I like that you do it properly, going back to metal and then protecting the metal... Best of luck with the move and the rest of the car's back end rebuild......

Gutted for ya thats a dream garage for sure! Can you do a video of why your moving if yoy dont mind a lot of us feel heavily invested in the car builds and garage build so were devestated for ya to leave it behind ☹️

Moving? Hope all is good Adam.

Id recommend you look at ce chem sprayable sealers way better for impact protection from small stones. I done the full underside of my evo v in raptor and the bed of my hilux. The hilux bed still looks fresh after 3 years of abuse but I think it’s too hard for small stones chipping away at it and it starts to come off. Have a look at redish motorsport underside restorations he has a great video of sprayable sealers.

Bilt hamber hydrate 80 rust converter is good stuff Adam

The raptor finish looks well Adam 👌.

5:25 my Mrs may ask why I'm rubbing my main sausage on a bit metal 😂 For rust treatment, try bilt hamber next time UK company and their product's are 2nd to none imo

I look forward to Adam's videos, can't believe he is moving and losing the garage, hope he builds another one 👍

Wee tip for shaking your cans mate. Drill a hole in old aerosol lids and stick in a nut and bolt. Stick them in your drill. Iv maybe got about 4 lids that fit all aerosols. Saves all that shaking 😂. Drill….2 secs, done Also, im a painter. We use raptor on all sorts of stuff. Its especially good for like bed liners and recovery wagon beds, nice tough stuff. Gives a nice rippled finish 👌🏻. A wee suggestion aswel mate. Get yourself some sikaflex. You can used it in all the seams and over weld lines etc before painting. (Like painters mate) It gives a manufacture finish and gives you many years protection. Just for when you do it next year mate. 👍🏻

Clean any areas that will get welded, and push the mig wire rather than dragging it

Must be a nice place your after with some land to give up your current place, best of luck mate,

Love watch in your videos m8t car looks brilliant hope you enjoy driving it…what’s your next project pal..👍👍👍👍

Awesome work, Adam. Glad to see you used some rust converter.

Great work Adam! I am doing so much welding on my classic mini on my channel…. Your garage and tool setup is amazing

I'd be gutted moving and leaving that garage behind, you've put so much time and effort into it mate. Funny when you mentioned your Bait early in the video. I'm originally from a little bit further north than you and moved to the West coast of Scotland 31 years ago, when I mentioned to the good lady many moons ago that I need to take some bait to work, she thought I was going fishing 🤣

Absolutely get it back on the road and use it there must be hundreds of restoration projects in barns and garages all over the world with the owners too old ill or passed away.The restoration can wait until it's falling to pieces it will always be worth doing properly eventually I would carry on the way you have started just so I could enjoy it and show it off.

Hi Adam,see you are using cure rust to neutralise the rust. I personally prefer Jenolite to do this as the phosphoric acid in the product seems to be more effective in doing a permanent fix. Good luck with the move and hopefully everything goes smoothly.

That Rapter piant job looks fantastic. I bumped into you last week at the old football ground.

Be interesting to see the new house. Hopefully it has a garage although you could buy one again

Good progress mate, although i wouldnt have been too happy with the red overspray when id just painted the floor black

Tidy job. The cars looking spot on .

Great content as usual. The car is coming together rightly.

Escort is looking fantastic you put a lot of Time money and effort into your garage but you know best for you and your family.

Have a look into Bridge End Works Ryhope Village mate, they have a few blank units it might be worth giving them a call and enquiring.

Nice job Adam ,can’t believe after all that hard work to build your workshop , you’re moving 😂😂that’s life ! Good luck 👍👍

Adam’s moving into Paul’s shed haha! He wouldn’t give this garage up unless another one is even bigger 💪🏼💪🏼💪🏼

Looks amazing, great job mate

Hahaha like the main sausage theory Adam. You crack me up sometimes pal 😂

Hi Adam, I find pannel wipe will remove wax oil save using a grinder

Great work mate, where did you buy all the driveshaft stuff and the bolt kit for the rear axle please?

Sorry you're leaving your garage Adam - I sincerely wish you all the best in the future mate

Great work Adam, surely that’ll last a few years now? Use and enjoy the car! Where are you moving to? Are you renting a unit to continue with your KZfaq channel?

Looking good mate, why bother stripping it down next year again, use it and enjoy it

That flap is to protect from Welsh Attack Rats from entering the car. They get you while you're driving the car - the first bite paralyses, the second, well you'll be dead before you hit the wall.. (even crazier during Rugby season apparrantely)

Can’t believe moving house after all the work with the garage and stuff

Good luck with the move Adam....I'd be lossed leaving that garage behind

Looks great!! I’d be happy with that work!!

Great work mate. Nice one.

Enjoying you content Adam i hope your moving is by choice and goes ok.

Always enjoy the videos on your channel best of luck with everything 👍👍👍

good job with the raptor, i want to do this to e36 m3, cheers

Great video mate 😊 moving your garage is mega 👍

Wow looks amazing mate well done r proper job that 👍🏽can’t believe your moving after doing the garage that is perfect for your 2 cars and you got lift in there too well good luck mate with the move I presume you have your reasons for moving big house 👍🏽👍🏽

You’re right mate, There’s nothing worse than working in a dirty Environment 👍

Please please please make sure the new garage is secure..And if you can.. keep its location a secret when filming

sit your paint cans in hot tap water for 10 mins..makes it way easier to spray.

Another good video Adam, keep it up. Can’t wait for the next one. 👌

Can’t believe you are bailing on the house and new garage! Hope the next abode is a better set up with a bigger garage 😎👍🏻

Looks spot on Adam!

Moving? But your garage is mint!

Great video Adam everything looks great when you move will you have a other massive garage again??? Cheers Paul

Can i buy your house, 😊 i want that garage its perfect, where's it advertised. Excellent job so far, it's looking fab 👌

Moving house? You just got the garage sorted for your car endeavours 🤔. You must have more space at the new abode. 😊👍.

Adam what air compressor you got in your garage pal? Could you show us and do a bit of a review? I want to buy one with a view to painting stuff but can’t find no useful UK videos

You actually love this car , wow is right mate

Top work Adam

Look at Hydrate80 next time mate.. much better than most other things available on the market

Mig should always be done 'downhand', ie. the pool should be horizonal under gravity. You can weld "vertical" and it looks like the "stack of coins" but overhead MIG welding goes against all established MIG welding principles. I do get it though. I'm an ex mechanic that went on to spend a decade in a Lloyds approved fabrication company. Mechanics don't have the luxury of rotating the workpiece to achieve optimum weld conditions. Going from welding sills on Fiestas, Datsuns and Metros, to offshore standard fabrication, I learned the difference. I don't live far from Adam, he does ok for someone not in the trade.

Love all your stuff Adam, especially with Paul. But it's only a matter of time before you chop ya fingers off. I've gotta look away sometimes 😂😂

That raptor is gnna be hard to get off

Your KZfaq are class Adam 😎

Garage seems like a bit of a waste of time and resource😂 the escort looks great!

She is a beast nice work!

great job adam looking good

mmm going by the looks of the other person doing it it looks like they just applied it over dirt and dust making it not stick, but tbh for the age it's ntb rust and rot wise, but truth be told most people don't really look after the under part of a car they just drive it and leave it for the next owner to do and also a dead give away that they don't really know how to maintain a car lol :) reminds me of my old mums car the color :) but they don't half look good in gray though

🤣Hillarious, you should be on telly! great job.

Looking good mate

You done really good 😊

Jesus Adam looks savage,my god moving house after you built a fine shed

So that was the deal Adam. You can have the cossie if your misses get a new house 😂

Has your welding wire gone rusty might be why the weld wasn't as good

Great video mate I love that car

Great work, but why didn't you sandblast the whole car floor?

Another cracking video 📹 Adam 😊😊

Enjoy her for the summer pal. There is always something else to fix at a later date.

12:36 memories on the tv 😂 glory days

Imagine if Adam moves into a little council house but buys 2 more Cosworths hahaha

Great content pal😊

Can’t believe you’re moving

Great update, 👍

Adam well done good to see a lad with great enthusiasm for a task and a have a go mentality a good watch keep it up!

Adam lad you really are doing a bonny job son, but do you not use weld sealer? It's pretty good stuff you know Adam lad!!!

the finish on the Raptor is better than Ford managed in the factory,

Need to take your garage with you

Aye that's come out well