I recommend a water dish as opposed to licking your finger as you handle bare lead.

Great video! Several years ago saw a video from Svartkrutt on paper cartridges, and used a dowel to make a mandrel and started making paper cartridges since then things have gotten better. Thank you for making it easier.

I have now used the .44 kit for 4 months. It is easy to use and makes good cartridges. I have personalized your steps . I recommend the kit. The beewax lube is very good. I do not always use paper cartridges at the range.

This is fantastic! I just ordered a kit and block for my 2 ROA’S. Can’t wait to try them out.

Tweezers or a small pair of pliers help in handling/inserting the bullet into the cartridge.

Great video, thanks!

Correct! I use the zig zag 1.5 but your punch is mine also... 5/8 and 3/4 I use elmers glue that is purple but dries clear. I made the 31 kit using a block of teflon 3/4" thick. The mandrel is made of wood and tapered and has an O ring at the cutting off edge. it is a great guide for a razor blade. The holes in the block are tapered slightly.. but I have like ten holes. this allows me to make em and leave em till they dry.. by the time I get to the tenth? the rest are dry. The O ring makes for a flare that sticks up a tad above the block. this allows a glued ball to 'fall' into the formed case. I drive the ball down with the edge of the cover for the glue stick. Not important for the conicals you use but essential for the round balls I use. again... by the time I finish the last I can punch em out of the block... having now 10 finished paper cartridges Oh... powder? I just use a flask I cut all my papers ahead of time I leave excess at the top and the bottom and just trim it off with a razor blade that I touch up with a stone every few rounds.. this is simple and results in sharper than factory. I said finished but they are not. I use a tray with lube (half beezwax and half tallow) and dip the ends into it. For 31 caliber I use a 22lr plastic case of 100 And yeah... LOL I get glue all over my fingers gluing balls... that is why 10 holes is better than one. and yes.. rolling a straight paper onto a tapered mandrel is problematic... but who cares? just roll it and trim both ends. a wrinkle? who cares? long as the small end goes into the chamber and the rest goes in far enough to turn the cyl under the ram? The gun does not care how ugly you made the round. nor... how compact the powder charge was in the cartridge. if that makes sense. I think the flare in the 'case' is important as you do not get the 'goofs' you mention. Kits... could do this by simply making the ball/conical end on the mandrel have a flare... none I know of do.

Great video thank you.

I wear gloves when handling the lead zinc bullets and the powder. As a measurer a .380 cartridge case with the spent primer still intact. Gives me a touch over 12 ounces for my 1851 navy revolver

"and that...is..a perfect paper cartridge.........................Except it isnt..." LOL excellent delivery.

I like to use papers that are not burned after shots co chambers are protected from residues that stick to them becouse paper cover. Ans when i shoot and reload i have something to take that half burned paper out. For cicles i use tea bags. (For constant paper thicknes and sure that fit my chambers , templates that i make i use paper from shop receipts. I was use flash papers but in shorts i stop use it becouse with time they make more problems that pros.

Interesting. So, for a New Army in .44, do the paper cartridges drop easily into each cylinder? Then use the load lever to seat the cartridge? How long can the paper cartridges last if kept in a sealed ammo box? Thanks!

Isn’t it easier to just load your revolver? Or just use extra barrel that you can change in 3 sec

great video,very informative. Where did you purchase the craft cutter for the circular pieces?

Good video

Thanks for the video. Not as easy as it looks. Seems like every one I make, I screw up three 🤦

Do you make kits like that for the 1863 sharps?

I'm dizzy now.

Ohhh!! I was trying to figure out wtf this was!! There musket shots! Am I right??

Cześć. Można u ciebie zamówić kopytko do cal. 36. I ten dziurkacz do Kołeczek papierowych

Looks like 3d printed kits

Is there no primer?