Part 1 JETWING EDF (LW-PLA)(Rudder) by PLANEPRINT 3D printed RC plane

Рет қаралды 4,950

2 жыл бұрын

Free tuning parts for wing servos available on the Planeprint page.
We are absolutely thrilled with the Jetwing.
From the concept behind it and from the implementation and the flight behavior. Hand launch, ground launch go without problems, the thing is fast, glides very well and makes us only fun, printed quickly, always fits in the car.
Congratulations to Planeprint on this jet!
JetWing:
Wingspan: 1270 mm
Flight weight: 1490 grams
Wingload: from 48g/dm2
4 channel
Motorization: EDF 70 mm, 4S
The components are the same for both:
Wing servos: CS238MG
Rudder servo: DS939 MG
EDF: Technical data:
Hacker Stream-Fan 70mm kv3750 (Wemotec Evo)
Motor: E40-S 1Y
Impeller: 9-blade glass fiber reinforced
Number of cells: 4S LiPo
15° motor timing
Thrust in grams: 2000g
Speed controller: YGE 90 LV
Battery: SLS 4000mAh
Flight weight:
1. 1465g
2. 1481g (Wheels)
All settings taken from the manual and fit very well.
Printers we have used:
4x Artillery Genius
2x Anycubic Vyper
1x Snapmaker 350T
1x Artillery Sidewinder X1
1x Anycubic Mega X
Flilament:
Sunlu PLA+
Polylight LW
Esun LW
Links:
Planeprint JetWing side:
www.planeprint.com/jetwing
Manual:
www.planeprint.com/_files/ugd...
Music from Uppbeat (free for Creators!):
uppbeat.io/t/infraction/hunter
License code: HSRKOPNFXWGLAIEB

Пікірлер: 36

@PorscheGt4 2 жыл бұрын

order it, now i have to print it

@moochasas 2 жыл бұрын

Purchased......... now to decide on what color to make it. Thanks team.

@printpilot3d 2 жыл бұрын

Acrylic spray works very well. Just don't use too dark colours because of the heat.

@moochasas 2 жыл бұрын

@@printpilot3d Thank you... I have a plane with black LWPLA parts... here in Australia where it gets to 40C in the summer black is a no no.. I usually go for white and red.... thanks again for a great plane.. I have a few of your planes and they are freakin awesome. kzfaq.info/get/bejne/fqh2orecs8XUYqc.html

@MarekSzulen 2 жыл бұрын

@@printpilot3d FIrst version of my jetwing goes with red fuse, green leading edges and white rest of the wings.

@jdduncan 2 жыл бұрын

Fantastic flights! I just completed mine and will have the maiden flight tomorrow.

@printpilot3d 2 жыл бұрын

Thank you, good luck. Don't be surprised if you have the take-off position, it goes up in the sky quickly, it's supposed to. I have 2 flight phases with flight phase trim, and it works great. Report back how it was, I'm still very taken with it, was there again yesterday, always great. 20 flights so far.

@jdduncan 2 жыл бұрын

@@printpilot3d I maidened my Jetwing this morning. Easy takeoff and only a click on right aileron trim needed. Got 3 flights in and am loving it!

@printpilot3d 2 жыл бұрын

Congratulations, it's addictive, isn't it? Especially you don't always need full throttle. I'm glad 😉👍

@printpilot3d 2 жыл бұрын

For me it is difficult to describe in English, but for me the JetWing is almost no longer a printed model, in terms of stability and strength, and in terms of flying, perhaps now that you have one yourself you will understand what I mean better.

@ericbarker3850 2 жыл бұрын

Like watching the trailer to a new movie... I will have to look into this more! I am hearing a few things, but I have never tried an EDF, because we don’t have an RC runway. But I think I might be able to run this one in our large grassy area.

@printpilot3d 2 жыл бұрын

Thank you! Hand launching is really good, it's not necessary to do it as hard as I did in the video, but with the Maiden, you want to be on the safe side 😉 .

@ohernand99 2 жыл бұрын

When is part 2 premiering? It's absolutely awesome!!! Can you show more details on the wheels you mentioned? I fell in love too

@printpilot3d 2 жыл бұрын

Unfortunately, I can't say when exactly, but it may still take 1-2 weeks. I'm glad you like the video. Yes, I can show it in more detail, have you already seen the little video of the creation of the JetWing?

@printpilot3d 2 жыл бұрын

In the description there is a link to the building description, which is free of charge, then you can already see a lot of what is being done.

@ohernand99 2 жыл бұрын

@@printpilot3d just did! You nailed it!

@jimhuisman5094 2 жыл бұрын

How much PLA is needed for the full build ? and is it normal or LW pla ?

@printpilot3d 2 жыл бұрын

Most of it is LW-PLA, but I put a link in the description that takes you to the building instructions, where you can see exactly what is printed from LW-PLA.

@DenisFerrari 10 ай бұрын

Fantastic! Did you paint the red stripes on last model shown, or stickers?

@printpilot3d 10 ай бұрын

Yes, I made a stencil and painted it. You can also see this in the preview video of the Jetwing (on the channel) 😉

@DenisFerrari 10 ай бұрын

@@printpilot3dgreat job indeed! Question: do you think I could print also the 2 rudders (for fuselage rudder version) as well as ailerons in LW-PLA, or better sticking to PLA as reported in the pdf? Thanks

@printpilot3d 10 ай бұрын

I printed all the flaps and rudders in PLA+, depending on the speed the rudders will warp. But what will work is if you print the rudders and flaps with 2-3 lines (LW) to be on the safe side.

@DenisFerrari 10 ай бұрын

@@printpilot3dso far I printed 2 rudders in PLA, very robust indeed, but their total weight (15% infill, no geoid on them at the moment) is about 22gr. Maybe 6% geoid filling still with PLA could let save some weight with them...? Thanks again

@printpilot3d 10 ай бұрын

Yes, I also only have 3% infill and the flaps. But if you are nothing else heavier with the other parts, you don't have to worry.

@rorywquin 2 жыл бұрын

Good info thanks. How do you find eSun LW compared to ColorFabb LW PLA.

@printpilot3d 2 жыл бұрын

Well, each filament has its advantages and disadvantages, you can take both if you don't print too hot or too cold. If you have Facebook, we could exchange more info. It's a matter of taste.

@MarekSzulen 2 жыл бұрын

Mine is ready to be assembled. Still need to wait for edf... I'm making the non-rudder version.

@printpilot3d 2 жыл бұрын

You will be thrilled

@MarekSzulen 2 жыл бұрын

@@printpilot3d That's the plan ;) Did you try also the non-rudder version?

@printpilot3d 2 жыл бұрын

If a large wing will appear in addition, I was considering it, because very likely the rudder will have little to no effect there. But I have two fuselages. So I would test with that first. You can fly more figures with rudder, and it's fast enough. For my part, I would always build with rudder (JetWing normal).

@MarekSzulen 2 жыл бұрын

@@printpilot3d hmm.. I still did not glue the fuselage.. might print the additional parts for rudder then :)

@printpilot3d 2 жыл бұрын

A new fuselage is quickly printed and the EDF quickly changed, fly it like this and if you are as enthusiastic as we are, print a second fuselage. For rolling in the grass I like to have the rudder.

@ohernand99 2 жыл бұрын

Hi! Is it possible to recycle a 70 mm EDF from a Horizon´s Viper to build this amazing jet? specs of the EDF: 2860 - 1850 kv. 238 grms. 12 blades. 6S. Can the Jetwing fit a 5000 mAh 6S? Say yes and I´ll purchase the plans right away :D

@printpilot3d 2 жыл бұрын

Compare it with my EDF or with the recommended FMS, a small 6s should fit, I can only recommend mine and the FMS from my experience. If yours should fit, install it, but I would be careful with more than 2kg thrust, you must take the larger servos in any case. 6s 5000mAh is too big.