Yamaha YXZ1000R Clutch Replacement | YXZ1000R Clutch Upgrade | YXZ1000 GYTR Clutch

Yamaha YXZ1000R Clutch Replacement | YXZ1000R Clutch Upgrade | YXZ1000 GYTR Clutch | Partzilla.com

Рет қаралды 12,501

Күн бұрын

Get a billet clutch kit for your YXZ1000R here: www.partzilla.com/product/yam...
Order 13 fiber plates: www.partzilla.com/product/yam...
Order 12 metal plates: www.partzilla.com/product/yam...
Don’t forget the gasket: www.partzilla.com/product/yam...
In this video from Partzilla.com, we’re installing a billet clutch kit on our YXZ1000R.
This unit is eventually having a turbo installed, and because of that, we wanted to perform a YXZ1000R clutch upgrade first. This will allow the clutch to better handle the added power from the turbo upgrade. Our YXZ1000 was previously equipped with a Rekluse clutch kit, and we’re switching to a Yamaha billet clutch for our YXZ.
We’ll start by opening the clutch. Some of the bolts at the bottom have copper washers, and you’ll need to take note of their locations. With the bolts removed, we’ll begin disassembling the clutch and removing the clutch basket. On the back of the clutch basket there is a gear we’ll re-use, and John will show you how to remove it.
With the old clutch removed, we’ll start building everything back up. This will involve bolting that gear onto the new basket and getting it installed. Then, we’ll start adding our clutch plates. Above, you’ll see that you need 13 fiber plates and 12 metal clutch plates for this stack. When we’re done, we’ll get the clutch closed back up.
Hinson clutch holder tool: www.partzilla.com/product/aft...
See the YXZ1000R clutch diagram here: www.partzilla.com/catalog/yam...
See the YXZ1000R transmission diagram here: www.partzilla.com/catalog/yam...
Our YXZ1000R gear reduction? Find it here: • Yamaha YXZ1000R Gear R...
Read more about our YXZ1000R clutch upgrade here: www.partzilla.com/blog/yamaha...
VIDEO HIGHLIGHTS:
Introduction - 0:00
Opening the clutch - 1:40
Removing the outer gear - 5:10
Assembling the new clutch basket - 7:00
Installing clutch basket - 8:30
Adding clutch plates - 11:25
Closing the clutch - 13:00
Find thousands of Yamaha OEM Side by side parts here: www.partzilla.com/catalog/yam...
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2016 Yamaha YXZ1000R, but you may have similar steps for your Yamaha side by side. If you’re not sure whether these steps apply to your machine, leave a comment and we’ll get back to you.
RELATED CONTENT:
YXX1000R oil change:
• Yamaha YXZ1000R Oil Ch...
YXZ1000R front brake pad replacement:
• Yamaha YXZ1000R Front ...
YXZ1000R rear brake pad replacement:
• Yamaha YXZ1000R Rear B...

Пікірлер: 19

@miguel5437 11 ай бұрын

So for my 2016 yxz I can remove the first 3 fiber plates that are thinner and install regular plates ? On an alba clutch kit

@emersonnogueira4246 2 жыл бұрын

Muito bom professor.

@jteddy11 Жыл бұрын

Hello do you have the part number for the transmission screen, the pull handle on mime has broken off, thank you.

@rubennperez9562 Жыл бұрын

Hola , porqué se rompen tan facil los Rulemanes y empieza a sumbar la primera? Mal mantenimiento?

@SirHamSki 2 жыл бұрын

2007 Gsxr 1000, clutch replacement 🙏🏽😎

@TheBreedxxx Жыл бұрын

Why do you have to reprogram the shift points ? Wouldn’t they be the same as factory set shift points .

@jteddy11 Жыл бұрын

I think it is funny, that they say they will answer comment questions and never do. Did you ever find your answer? I have a question for you, I picked a used 2016yxz manual shift, shifts fine running but just getting it going is super hard, engine stalls, it even came with a heavier flywheel. Pulling away in reverse I can keep it running without stalling, forward 1st gear I have to rev the shit out of it to keep it running and studder away, does that sound l just need new plates to you? Good luck with your question, and thanks

@PartzillaParts Жыл бұрын

You have to reprogram the shift engagements points on the Sport Shift system as it is controlled by the ECU mainly because of the gear reduction kit I had already installed. I will not have to on this unit as it is a Standard Shift. In essence, a manual shift. No flappy panels on the steering column.

@Mrsomething854 2 жыл бұрын

I inow thIs has nothing to do with the video but I have a 1991 Yamaha big bear 350 and it bogs at full throttle I’ve torn down the entire carb looked for vacuum leaks everywhere and it still bogs I have never looked at the valves though any ideas?

@eliasnohair7963 Жыл бұрын

Valve clearencing could be off/ or throttle body sync could be off

@anthonyk6265 Жыл бұрын

Is it an oem carburetor does it have two throttle cables that could be the issue you can get one on eBay or find one off a different model that doesn't have the two throttle cables the the butterflies and the throttle cables get out of sink and they don't work right

@anthonyk6265 Жыл бұрын

John Talley taught me everything I know

@Mrsomething854 Жыл бұрын

@@anthonyk6265 I have a aftermarket carb with a single throttle cable

@Mrsomething854 Жыл бұрын

@@eliasnohair7963 I’ve recently adjusted the valves and they are both good and I don’t have a throttle sync