Well done thx for your informative video. I think the anti tilt is my problem and I’ll fix it tomorrow . I was going to throw it out, but now I understand how I can fix it.

This was the easiest and quickest way to figure out the problem with my heater without damaging any of the equipment or wires.

Man... THANK YOU!! I nearly beat my brains out trying to troubleshoot this, but within 10 minutes of watching your video, I had the tilt switch bypassed, and I’m back in business!

i temporarily bypassed mine, just like this and it works great. have ordered a new tilt switch and will replace once I get it...

Mine was the gas tube, full of black gunk. Used an air gun and blew it all out, heater works perfectly once again. Thanks for the vid.

OMG...if would have watched this first I would have saved 3hrs of my precious weekend...it worked!! 😊

This was a huge help, your comment about the tilt switch lead us to a broken connection!! Thank you!

Thanks for this video. The dump switch on my unit also went bad. This saved me a lot of time. Merry Christmas.

It was my tilt sensor. You're the man

Great job and I'm glad you spoke about the importance of safety by using gloves and the importance of the tilt switch. People are forgetting that the tilt switch and the thermocouple are connected. Thanks you for a safety 1st video

This was an exact replacement for the old one that lasted about 10 years. kzfaq.infoUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh The top of my mitigation tube by my roofline was just a 90 elbow which allowed too much debris to fall down into the fan, eventually ruining it. Without this issue, I bet it would have kept running another 10 years. When I replaced this fan, I added an extra elbow joint so the top tube now it does a 180, which should solve that problem. The radon guys around here wanted to charge me a $300 diagnostic fee, then parts/labor (probably close to $600 total). I installed this all by myself in about an hour for the cost of the fan; it would probably be even easier/faster with two people. FYI the manufacturer's warranty greatly differs depending on whether you install it yourself (1 yr warranty) or have a licensed installer do it (10 yrs).

Perfect instructions and I just ordered the part from Amazon. By hot wiring to TEST if it was the tip switch was great advice. Thank you for making this video

IM FROM ENGLAND AND I COULDNT STOP LAUGHING AT THE FORREST GUMP ACCENT SORRY BUT IT TICKED ME PINK GREAT VIDEO THOUGH THANKS

Just figured out myself it is the tilt switch that's done on my heater. It's grand to have these kind of educational videos ready on the web, rather that havin people watching people play some stupid shite game. Thanks for the video!

Great bro. It help me a lot. I did the same as you, removed the DUMP SWITCH and the problen fixed Thank you very much

Thank you! For me, cleaning the pilot did the trick. I order a couple of tilt switches just in case.

Perfect! My heater is back operational again now (bypassed the tilt switch). Thanks for taking the time to post this.

thank you I fiddled with this heater for couple hrs back at it tommorow with some good ideas tyty

Same problem on mine change that switch and worked perfectly

Thanks for this as I was able to revive our patio heater that had a clogged pilot tube. Works well now.

Great video and fix. 👍👏

Thanks mate for the info. It's winter on the east coast of Australia at the moment. I shorted the 2 wires on the tilt switch (exactly the same switch as your video) and heater is now staying lit. Last night we jammed an empty beer can between the control knob and a table to keep it going. Don't need to now. Our heater is much shorter so minimal chance of being knocked over. Cheers :)

Awesome! I kept looking everywhere for this issue and the fix. Thanks!

thank you so much from the UK!

Fantastic job explaining all the details, much appreciated. Thank you for sharing the knowledge.

Bypassing the tilt switch is dangerous. You DO NOT need to buy a new tilt switch. All it has in it is a ball bearing, a small strip of metal that the ball hits against and pressed against a button that cuts the circuit. The small strip of metal has a round piece of plastic that the ball hits when tilted. That piece of plastic can get hung. Give the tilt sensor a couple taps to see if it releases. If not, carefully pull it apart, which will release it. Press on the plastic that the ball presses against and make sure the button at the other end of the metal strip is going on and out. Real easy fix without sacrificing safety.

Yep-Exactly what was wrong with it!!! Mine came with the defective switch from the store. Crammed a wire across and good as new! Thanks!

Genius! Bypassed the tip sensor and bingo! Thank you!

Yessss! This did it! Cleaning the pilot tube got the pilot working again but it would not stay on. Bypassed the tilt switch and now it's working again. THANKS!

Thankyou this worked instantly

Nice work...I'll have a go tomorrow....btw you should do voiceover work ...you've got a great accent !!!

This is a great explanation and just what I needed to get my patio heater going again. Isolating the tilt switch as recommended solved the problem. I also took apart tilt switch as someone else recommended but a replacement is still required. The cheap failed microswitch is the culprit. BTW, disregard the humoured, arrogant and opinionated UK guy who obviously thinks his version of English is superior to yours and likely others. Best regards from Down Under.

This was a huge help, thank you

Thank you - just fixed my Amazon Basics tower patio heater

Thank you for this video!

You can run a wire down the heater tie it to something heavy so when it falls it yanks out the attached rigged wire .

Thank you.very helpful information.

Great help, thanks for posting this video.

The thermocouple produces a very low voltage (typically less than 20 millivolts) and current which activates the gas safety valve. The problem is that quite often the tilt switch (sometimes called a dump switch) has contacts that get a little corroded and increase the contact resistance just enough so that the gas safety valve doesn't operate.

Awesome, I was having the same problem and this was helpful

Many thanks....worked like a charm.

Thanks a lot ! It was my switch too. I subscribed

That did it! Thanks.

If the pilot light stays lit, but feeding it full gas results in no audible gas flow, then this is likely your problem. Often you can flip the connectors and marry them to bypass the mercury switch. Obviously, you've just disabled an important safety measure, but it's good for confirming which part needs replacing.

Thank you, you did fix my heater 🔥..I did do the bypass and im leaving it like that... The main thing is to cut the gas every time your not using it. My hearer in on a 4 stand..not easy to push over. Again thanks for the video

Will check it out, cheers from Australia!

Good Job Man Thanks !!!

Just an easy way to check the tip switch! Unplug the two wires, slip the plastic covers back just a small amount and slide the two ends together using opposite sides of the slip on connectors. (They will connect easily when two of the four rounded overlays are slipped together!) If your unit now works and lights you know the switch is the problem.

May I ask if you can publish a heater assembly video for us, and we will provide remuneration. Looking forward to your reply

FYI, The jumper wire not only bypassed the tilt switch it also bypassed the thermocouple.

I tried all of those things and it still will not light. How can I check if the regular is bad?

Can you share the link to your Amazon purchase? I have the same heater but see a few different kinds

I'm looking for a parts house that I can get a Thermocoupler from? Brand of heater is Inferno I'm in Austin TX, yes it gets cold down here sometimes. 32* out there right now. Mamma's cold out there and I hate starting from scratch and a cold start.

One other thing to remember is that when the gas is first turned on after a repair or when changing tanks, the propane has to bleed through the tiny pilot orifice before it can ignite. Might take a minute or two and then will fire up.

Traducción en español

I bypassed mine and it still wont stay lit

Need to start manufacturing quality USA again.

To take apart the kill switch and fix. kzfaq.info/get/bejne/eLydhK2TpsfcY3k.html

Junk. All junk. I have bypassed all my tipover switches that have failed. Junk. Chinese junk.

good video but he talks to much

Thank you...

Add to your round top dome patio heater by installing The Patio Heat Director Adjustable Movement Reflector : www.amazon.com/REFLECTOR-ADJUSTABLE-Heat-Directional-Patio/dp/B08JYRP5HN/ref=sr_1_15?crid=1ISYXVOLEY6SD&keywords=patio+heater+reflector+shield&qid=1662774105&sprefix=%2Caps%2C160&sr=8-15