STANO_HACKS trying out the Permatex spray and seal... As an Amazon Associate I earn from qualifying purchases. Permatex spray and seal - amzn.to/41E80tm
Пікірлер: 36
@apachecatcat34954 жыл бұрын
I have used this stuff on oil tanks with tiny holes. It’s very watery if you just spray it on , so you will make a big mess. I spayed some into a container and kept stirring it until it had somewhat thickened. Then I applied to the leak with a brush.
@williamhaskellhaskell31622 жыл бұрын
Also let the leak cool off a bit. Then apply!
@michaelprice37854 жыл бұрын
Just sprayed it on a pin hole leak on my heater core copper line where it attaches to the hose at the firewall. Wish me luck. Do not want to change the heater core. I suppose I could solder the hole. Is in the brass pipe.
@dtruth57693 жыл бұрын
How long did u wait between applocations
@sydneyNemesis1014 жыл бұрын
going to try it on my bmw, to slow an oil leak on the oil pan, cross member is on the way to access my oil pan, so this would be the best solution..... did you say, ensure car is at operating temperature? then apply sealant 3-5x and then let it set for 45min? if it slows it down great if it stops my leak, it’s a win
@ScienceMonkey004 жыл бұрын
Glenn Chow Hello, i ended up replacing my front seal, but it did slow another leak associated with it. Get the car up to temp, then spray, wait a couple of minutes before coats. Then let dry at least 45 min or so before using the car. Good Luck.
@voidisyinyangvoidisyinyang8854 жыл бұрын
@@ScienceMonkey00 gonna try it tomorrow on the front differential seal - thanks
@gweedomurray99232 жыл бұрын
Depending where the over spray goes I may just leave it as rust protection.
@ScienceMonkey002 жыл бұрын
Lol. That’s the way I look at it.
@williamhaskellhaskell31622 жыл бұрын
Hi. Good job. Did you clean the area with 140 deg water with degreaser. With brush and rag scrub out. Then alcohol or brake cleaner. To remove all grime. And oil. Then apply the product? Don't be lazy. Bill
@ScienceMonkey002 жыл бұрын
Thanks will for the tips...next time I'll give it a go.
@MichaelRyan-mt4on3 жыл бұрын
What did you paint your Jeep with ? It looks like colored bed liner. Looks good by the way !
@ScienceMonkey003 жыл бұрын
Hello, it was a raptor liner kit from Amazon.
@dynodonfb73 жыл бұрын
Will this work on a weeping rear main seal?
@ScienceMonkey003 жыл бұрын
It should
@jaikobmackney30303 жыл бұрын
Can this stuff work on a waterpump that already has rtv and a leaky gasket?????
@ScienceMonkey003 жыл бұрын
It doesn't hurt to try. I would think it may work.
@markdurst73733 жыл бұрын
Can you apply a coat the day after you sprayed it on
@ScienceMonkey003 жыл бұрын
If I remember correctly I believe I did another round a day later.
@drexellake40513 жыл бұрын
Will it work for vacuum leaks without damaging anything internally?
@ScienceMonkey003 жыл бұрын
Hello, its a good question. When this stuff sets its pretty solid. So I would think that as long as you let it completely set it may work. If it stops stuff from coming out, why not from going in.
@luisponce147210 ай бұрын
drexellake if The Vacuum leak is big with a big hole it won't work but if the Hole is Small it Will work for Big Leaks I Recommend Silicone Sealent Tape just Stretch it and Apply it Tight on the Area or Hose and Electric Cables it is Heat resistant
@TJ-xt6pc9 ай бұрын
Would this work on a seeping oil pan bolt??
@ScienceMonkey009 ай бұрын
It might…it’s worth a shot.
@peteskipeteski44643 жыл бұрын
DudeSki, Seriously-No Safety Goggles/Glasses!!!!
@jameswaugh115 Жыл бұрын
Will it work on leaking valve covers?
@ScienceMonkey00 Жыл бұрын
It's worth a shot! But depending on the motor, it may just be easier to change the gaskets and use some permatex indian sealer with them.
@CUSTOMWORKS7.3PSD3 жыл бұрын
You didnt use it correctly I use it all the time with no failures, Tips what ur spraying needs to be clean very very clean, shake the can 3 times for a minute each put can in hot water get the contents hot then shake again make sure what your spraying is clean and spray short light coats min of 5 times leave sit 12 hours in 70 degree min temps
@ScienceMonkey003 жыл бұрын
Good to know!
@sarahobrien33792 жыл бұрын
What if it's 30 degrees outside?
@CUSTOMWORKS7.3PSD2 жыл бұрын
@@sarahobrien3379 no don't waist your time 70 or better
@residentevil98944 жыл бұрын
Is it hard to get off ?
@ScienceMonkey004 жыл бұрын
I haven't tried to, but it looks like it is pretty tough to get off after it sets.