Installing Fel-Pro Cork Rubber Valve Cover Gaskets

Рет қаралды 32,094

Жыл бұрын

Properly install a cork rubber gasket with information right from the manufacturer.
Visit www.felpro.com to find out more

Пікірлер: 56

@arthurrose6473 Жыл бұрын

Excellent, thorough and important video, where the devil can be in simple details- a leaking valve cover gasket is a very common and annoying problem well covered here. Also with rubber gaskets now FAR more expensive, people are going back to "kork", such as myself! Thanks!

@PetesGarage Жыл бұрын

Great point!

@DJSekuHusky Жыл бұрын

Thank you for posting this; I'm doing a full rebuild on my 2001 Xterra and the oil pan gasket for the KA24DE calls for a cork rubber gasket. I ended up getting a Fel-Pro gasket. I remember the old-school mechanics who taught me saying to not use RTV gasket maker on cork rubber. What threw me for a loop was removing the old oil pan and finding the shop that had done the oil pan gasket when I bought the vehicle had used some kind of sealant to bond the gasket to the pan. I'm replacing the original pan due to deep rust, otherwise I wanted to double-check what procedure was correct prior to reassembly. Your video was quite informative, I'll be sure to read up.

@PetesGarage 11 ай бұрын

Awesome! Thanks for sharing

@richardoliver1303 Жыл бұрын

I was taught in the early 60's by some older wise mechanics to turn your pan or cover rail upside down on a piece of wood and place the ball peen side of a small hammer against the bolt holes one at a time stiking the flat side of that hammer with the flat side of another pushing the bolt hole straight in line with the pan rail. This helps the pan or cover to not leak!!!

@PetesGarage Жыл бұрын

Great comment, thanks Richard

@TahoeRealm Жыл бұрын

Geez Pete, just in time! I’m installing a Fel-Pro gasket like this on my 59 GMC in the next two weeks! Thank you very much. Sorry I haven’t been texting you for advice lately, I know you miss me and my 270😂😂

@PetesGarage Жыл бұрын

Timing is everything. I'm always happy to help

@mattgeiger2627 Жыл бұрын

Fantasic details, thank you. Cant wait to watch head gaskets video next.

@PetesGarage Жыл бұрын

Thank you!

@5798Mike Жыл бұрын

Great content Luv ur videos

@PetesGarage Жыл бұрын

Thank you so much 😀

@davidkeeton6716 Жыл бұрын

What we as customers/ users of Felpro gaskets, and I have used and sold them since 1978, is why, I mean why don't they make the silicone gaskets with the steel reinforcement and anti compression sleeves for the transmission pans of all the popular American transmissions that are used in performance applications? Or more models of engines for the valve covers?

@PetesGarage Жыл бұрын

That's a great question. The market probably isn't big enough.

@ck1insac Жыл бұрын

Hey Pete, you ever use the Fel pro corkprene gaskets for the China wall on a SBC? I got a set that came with the Fel pro intake gaskets. Seem like they would work better than just the bead or sealant. ??

@PetesGarage Жыл бұрын

Yes, they are good, as long as you have no had the deck lowered too much

@joeidaho5938 Жыл бұрын

Having no problem with leaks on my 302 engine that was rebuilt about 2 years ago...using Fel-Pro gaskets. What I do have a problem with is my e4od transmission. No matter what type of gasket I've used, I end up with leaks. The real problem, in my opinion, is that the e4od stamped steel pans are not made to handle the recommended torque spec...which is 10 - 14 ft lbs. I tossed my original pan, bought a stamped steel Derale pan...and got the same bolt indentations in the pan...that caused a leak...and it was just a matter of time. I've used RTV...and no RTV...and there is really no difference. I keep spending money....and am waiting for a Moroso pan...with a billet flange, that shouldn't flex when I install the pan bolts at the recommended 10 ft lbs. My thought is that, for flexible pans, the manufacturer really should be supplying braces, as I have on my oil pan, to prevent pan warping and bolt indentation that causes leaks persistently. Also bought a neoprene Moroso gasket...and will be installing it without rtv/sealant, so it can be reused whenever I open up the pan again. Honestly...these large transmission are a pain in the ass, in regard to leaks from the pan. I'm hoping to have found the best solution. Will know in a few weeks.

@PetesGarage Жыл бұрын

Thanks Joe, I hope that works. Thanks for sharing with everyone.

@Sm-ne8ff 9 ай бұрын

Very Good Video !

@PetesGarage 9 ай бұрын

Thank you very much!

@Karrpilot 11 ай бұрын

If available, I tossed the cork gaskets into the trash bin and got the metal rail gaskets with rubber lining. Did that on my 327 Chevrolet valve covers and never had another leak.

@PetesGarage 11 ай бұрын

I did the same

@440Nichole Жыл бұрын

I've seen videos recently where guys are recommending spreading petroleum jelly over the the cork gaskets . what are your thoughts on this ?

@PetesGarage Жыл бұрын

If the manufacturer does not recommend it, I wouldn't do it.

@jayare9160 Жыл бұрын

Is the blue side supposed to go on the block? One side of the gasket has blue and the other does not. Does it matter?

@PetesGarage Жыл бұрын

It should match the surface. It may go either direction

@Arizona_rider 11 ай бұрын

I’m a video kinda guy. This is actually a really good video of what we should do… let’s do this

@PetesGarage 11 ай бұрын

Thanks my friend

@kgroombr Жыл бұрын

I had no clue about those tabs. Been doing it wrong for years.

@PetesGarage Жыл бұрын

Always something new to learn

@infrasonicrebasses4763 Жыл бұрын

how do you get the cork gasket soft ??

@PetesGarage Жыл бұрын

it should come that way

@Oopsitsme77 6 ай бұрын

How long would I have to wait to drive the car once the job is done?

@PetesGarage 5 ай бұрын

Maybe an hour or so

@steve1374 4 ай бұрын

Easiest way by far, install temporary studs made from long bolts with head cut off. Install the gasket over the studs, install the cover, or component, install bolts and remove studs. No chance of damaging gasket and all bolt holes line up.

@PetesGarage 4 ай бұрын

Thanks

@arianduran1725 3 ай бұрын

Why do people use silicone sealant & or Grease/Vaseline?

@PetesGarage 3 ай бұрын

Everyone has a preference or way they think is best

@deanharris7149 Жыл бұрын

Cork gaskets use Gasgacinch or Indianhead Shellac. Seals cork gasket pores.

@PetesGarage Жыл бұрын

Interesting

@MrKentaroMotoPI 11 ай бұрын

Sealing is not required. The purpose of those glues is threefold: 1. Adhere the gasket to the cover so that it comes off with the cover and doesn't leave pieces on the engine surface. 2. Keeps the gasket in place during installation. Despite the locking tabs, the gaskets may fall out under their own weight. 6 cylinder valve covers are notorious. The oil pan rail gaskets on this engine fit under the end seals. They must be glued into place when replacing the pan in the car. Good video topic 👍 3. Reduce gasket "drift" during tightening. V-8 intake manifold end gaskets are notorious. The Ford small block V-8 (cousin to this 6 cyl) is notorious since those surfaces are machined. The OEM gaskets were glued in place; you had to chisel them off. I liked the Indian Head because it had an Indian head on the bottle. It smells cool, like something illegal. My boss at the gas station in the '70's liked 3-M Weatherstrip Adhesive. It tacks quickly, but stays somewhat pliable so it's fairly easy to remove. It is also compatible with the cork-rubber gaskets.

@belloa3026 Ай бұрын

I used fel pro cork gasket on 1978 Chrysler and it is leaking. Did everything manufacturer said to do

@PetesGarage Ай бұрын

Is the valve cover straight?

@belloa3026 Ай бұрын

@@PetesGarage yes.

@belloa3026 Ай бұрын

Hello, I bought those and installed with no sealant. it is leaking a little oil in the bottom of both sides. Should I remove and put some Permatex Sealant liquid? Fel pro vs 13379

@PetesGarage Ай бұрын

I would put some sealant on them and don't over-torque