Pierburg 2E3 Carb Rebuild & Adjustments for VW T25 / T3

Рет қаралды 70,133

Күн бұрын

Step by step instructions where I talk through rebuilding and adjusting a Pierburg 2E3 carburettor for the Volkswagen T25 / T3. Rebuild kit from Brickwerks. The PDFs mentioned in the video are available on the blog: vwt25.blog/2016/09/15/pierbur...
If you would like to help support James' channel please consider making a donation. Any money raised will be used to buy tools and equipment to help produce new videos. Click this PayPal link to make a donation: paypal.me/JamesAkersGB
This is a reuploaded video with louder audio. Original version: • Video

Пікірлер: 90

@richindex96 3 жыл бұрын

I'm about to rebuild my carb! I've never had a carbed vehicle before so it's all new to me! I understand the very basics of them, but this has explained so much already! Gonna be watching this again and again when rebuilding mine I think

@JamesAkers 3 жыл бұрын

Hope it goes well!

@chrismurphybiz 7 жыл бұрын

I have watched this so many times now as I rebuilt my carb. Thank you so much, really clear and helpful. saved me hours of reading and scratching my head!!

4 жыл бұрын

Man, you helped me so much! I had no idle and I followed you assembly guide. I cleaned out every single hole in the carburettor and now I have idle and the car goes much smoother. Thanks! If you want to know, I have Skoda Favorit 135 LX with the same carburettor.

@adamzahradnik3146 4 жыл бұрын

Keby si potreboval nejakú pomoc ozvi sa :)

@TheSgtAngry 5 жыл бұрын

For anyone wondering what those marks at 35:07 are for, they're used to set the summer and winter mode for the choke. Also would really recommend making a vacuum generator using an old bicycle pump fitted with a gauge to get correct measurements because those can vary quite a lot if the parts are faulty. Also makes it easier to set up that way because you don't need to hold anything together with a rubber band.

@damianokane6161 Жыл бұрын

Thanks for this. Do you know which mark is for Summer?

@TheMinibus591 7 жыл бұрын

super video! I tried to refurbish my carb before but I'll do it again because now everything is very clear and I think I missed some bits :-) Thanks a lot!

@jasondesignmedia7495 3 жыл бұрын

32:35 very interesting look at the infamous fast idle cam adjustment on the 2e3 carb, thanks for posting this carb rebuild.

@difacilprojects6676 5 жыл бұрын

Thanks for the video and regards from Spain.

@reecethornley4485 2 ай бұрын

Thanks so much for your extremely insightful and useful videos! I hope this rebuild brings my van back to life!!

@richindex96 3 жыл бұрын

Was following this video today! Soooooo much help for a first timer! So simple and clear! Unfortunately when removing my 'injector' I managed to snap the 'spout' part off 🤦 so gotta take my spare carb apart to steal that one! Otherwise this video is **** hot accurate and perfectly descriptive, but not tedious or boring! Honestly so much help. Thank you

@xclaassen5463 Жыл бұрын

Brilliant job you have done, greetings from Germany.

@annasrabah8195 3 жыл бұрын

Great video, thank you for every frame 🎉

@philippkoch9579 2 жыл бұрын

Very helpfull and professional Video. Thanks from Germany 🚐😎🙏

@Harryroth100 6 жыл бұрын

Really helpful video! Many thanks!

@AjCarburadoresAlan 7 жыл бұрын

parabens pelo video ,muito bom ,aqui no brazil eu retifico carburadores tambem

@krzysztofwnuk6298 2 жыл бұрын

Thanks for a great video it is really helpful with the rebuild of my pierburg for the 1988 LT31

@JamesAkers 2 жыл бұрын

Hope it all ticking over nicely.

@krzysztofwnuk6298 2 жыл бұрын

@@JamesAkers Thanks for asking, actually the car still ides quite bad, it does start but with the help of the throttle. After getting a bit warm it starts to have problems (like running on 5 cylinders only). I suspect the problem is the choke flat that does not open and close when it should. I set it up to max 3,5 mm open but this does not help much. I ordered a new choke pulldown unit (original) maybe this would help. Is there any other way to test if the choke mechanism works?

@IagoPereira 5 жыл бұрын

This video is just GREAT!!

@SonicStriker43 6 жыл бұрын

Nice and clear, thanks!!

@valeriomarletti6271 5 жыл бұрын

Bellissimo video! Grazie mille!

@sebdi9308 Жыл бұрын

Thanks for the great video !!

@JC-ECUConnection Жыл бұрын

Brilliant vid thanks!

@Urge38 Ай бұрын

Once you notice it, you can't help but hear it !!! Smacking your teeth every 30 seconds lol good video, only thing worth mentioning is the vacuum restrictor does NOT sit in the pipe, it pushes into the end tube of the vacuum

@JamesAkers Ай бұрын

Thanks - I'll go back in time 7 years and make that change 😆

@angelgerardomondragoncruz65 5 жыл бұрын

A great video about adjustments. thank you for the info. I have only one question. when you fit the jets in the primary and secondary venturies you show two numbers, 102.5 and 110, what could happend if I have 105(primary) and 117(secondary)?

@yassermamon671 6 ай бұрын

Good morning james i am so happy to now you. Please i need that catalogue

@enzoamericano 5 жыл бұрын

Hi James, and thank you for your nicely videos! Have you any experience on Brosol carburettor to replace the original Pierburg 2E3 (fits 1.9 DG engine code Waterboxer engines)? bye bye

@davidjones1555 2 жыл бұрын

Great videos. I’ve watched this one all the way through more times than I care to admit. Still struggling to set my carb up though….it really struggles to start in the cold, I push the throttle in to set the choke flap but it just doesn’t want to start, then the auto choke warms and opens too quickly and the carb guzzles in lots to cold air and bogs down and stalls! Once warm it runs really well. Any ideas?

@johnblackmore4772 2 ай бұрын

Great video. Any tips on how to determine its a carb issue ? Our t25 has lose of power. Thank you

@CainaSurf 5 жыл бұрын

The accelerator pump volume, according to one of the manuals should actually be 0.326 ml (cm³), which is way lower than what is in CJs manuals... Also the duration of the stroke, and the gap between seem to be switched...

@JamesAkers 5 жыл бұрын

You're right about the pump test, it should be 1 second pump and 3 second wait! I thought i'd double checked the volume from the other manuals, i've have to re-check.

@CainaSurf 5 жыл бұрын

@@JamesAkers thanks for the video btw, helped a ton!

@jorge8281 3 жыл бұрын

Thanks a lot for this video. Maybe you could help me with the carburator electric conexions. I don not know which ones have to be connected do direct posivite ignition and which ones to the temperature sensor. Thnk you

@DBMiniDIY 4 ай бұрын

Great video, it will help me greatly, along with your other ones, Do yoy have a link where you gir the fuel inlet filter/strainer. I cannot seem to find any online

@johnblackmore4772 2 ай бұрын

I changed the fuel filter and cleaned out the carb inlet fuel filter and it worked for a while then same lose of power came back. Do you think the fuel pump could be gunked up ?

@chrisbentley8631 25 күн бұрын

Hi James, cracking videos ... Just found I have a Weber instead of the intended pierburg 2e3. It has some leaks and uneven running, the Weber is 2701 model I believe ... Shall I go back to pierburg?

@logik4264 2 жыл бұрын

5:19 Is that air corrector jet allows the air to float chamber to generate more atmospheric pressure in the chamber and pump more fuel through the nozzle? So if mine running reach, do I should screw that jet in or unscrew it to get the mixture leaner?

@faysalrami9912 4 ай бұрын

Merci شكرا

@philiphuw 4 ай бұрын

My choke pull-down unit isn’t working (diaphragm perished) and you cannot source another one for love nor money. Everyone is sold out. Does anyone have any suggestions? I was thinking maybe block off the tube to the unit then try do adjust the small Allen screw to get the choke flap to open slightly (3mm if possible) when cold. Anyone?

@paulcrosbie2195 Жыл бұрын

Do you have any idea where i could get a replacement biometalic strip (or choke heating element) ? Can’t seem to source one

@g-sailing4427 3 ай бұрын

Hi James, do you know off hand where the fuel idle cutoff is wired to? I can’t see it in any of the vw or Haynes wiring diagrams. Thanks, Glenn

@anthonyjerome6719 3 жыл бұрын

I'm using the same carbeurator in my opel kadette and I'm having a problem cause it keeps on overfloading any advice please

@fabiohernandez6915 6 жыл бұрын

this carburetor Pierburg 2E3 is the same as the Kadett 1.6S???

@alexanderiskander9621 Жыл бұрын

Do you know if the spacer and gasket(s) are required for the pierburg 2e2 carburettor?

@alexanderiskander9621 Жыл бұрын

Hi, just a bit confused about the jets, you changed the jets for the primary and secondary Venturi, and the air correction jet you changed just one, am I not correct in thinking that the secondary Venturi air correction jet needs replacing or is it fixed and can't be changed.

@tomken18 7 жыл бұрын

Hello are al the setting the same for al cars or do they al need different settings? I have a vw Jetta 1.3 from 1986 and i want to clean up my carb. to. my carb. is exacly the same like yours. Great video! Thanks.

@JamesAkers 7 жыл бұрын

Hi Tom. I've just checked the Haynes manual and the settings for the 1986 Jetta are: Choke pull down - (a1) 2.4 +/- 0.2. The jets and float level are the same.

@tomken18 7 жыл бұрын

James Akers ,sorry for the Verry late response. I did not get A Message of your reaction.. Thank you Verry mutch.!

@himaforlove 6 жыл бұрын

💖💖💖💖

@gordan9988 5 жыл бұрын

Hello.. Can u help me about carburetor Pierburg 2e in Golf 2 1.6-1.8.. I exchanged many carbs but all couldn't work...i did more and more profesional carbs service but its not work again after some days... I wanna try fix my carburetor now..is this instructions in video for my carburetors..can i adjust carb same as in video? Thank you.

@ziome3eg 2 жыл бұрын

I've run into a problem with my pierburg 2e3 rebulid. My pump injector doesn't spray any fuel, i've tried blowing some water thru it even with ball inside pressed but feel's like it doesn't do anything, is it normal (my car is golf 2 with 1.3 engine if that matters)

@ArchyBaldo 7 ай бұрын

Do you need to put petrol in the chamber before reinstalling it?

@vladimerdolidze929 6 жыл бұрын

Hi my carb have always full open automatic air flap Can u told me why? Or how can I fix it ??

@olivereason564 Жыл бұрын

When the lever by the cam on mine goes down after the accelerated itls pressed fuel sprays out for the lever any suggestions?

@helivonkopter3570 3 жыл бұрын

Hello James. So happy to have found this video. This might be a silly question, I don't know much about mechanics... yet... My 1988 T3 just had a new engine put in and the mechanic opted to upgrade from the 1.9l to the 2.1l using the same carburetor (Pierburg2e3). I have a few issues (gas mileage, stuck throttle control, missing lever for choke flap) and am now wondering, before completely taking the carburetor apart and/or looking for a rebuild one, will it ever going to work properly with the 2.1l??

@JamesAkers 3 жыл бұрын

Hello! Yes, there are loads of people using the Pierburg 2E3 on the 2.1L and it running really well so would definitely recommend giving it a refurb. Search on the The Samba (www.thesamba.com/vw/forum/viewforum.php?f=20&sid=1cadc8374c5848ba2d62cee81d3d8217) and Club 80-90 (club8090.co.uk/forum/) forums for examples. Let me know how you get on!

@helenerohr582 3 жыл бұрын

@@JamesAkers Ah, only just now realized that you had responded. Thank you so much!! I have also contacted you with my other email on another video of yours...I live in the States and am learning that a carburetor is not the best part to have in the engine, as that version of the VW engines never officially made it to the states. I am determined though to get that thing fixed LoL. The spring from the throttle control is missing and also the lever that attaches to the choke flap is gone. Maybe a few other parts. Those are the two obvious ones. I am on a back order list of sorts for a carburetor coming from the UK, but that might be a while so I am trying to figure out what parts the two missing ones are to possibly order those somewhere and start rebuilding.

@currierplastering Жыл бұрын

I'm about to rebuild my carb however it never had the small red filter on the pump injector and it doesn't come with the kit! Does anyone know where I could find one?

@guusvanmarle7344 2 жыл бұрын

Do you know where i can buy a new 'radioactive warning sign' washer? Mine was so corroded it just crumbled into pieces upon removing it.

@latmosbisiklet2212 7 ай бұрын

chok flap space for Pierburg 2E is 2.5 mm ?

@elvinkasumovic3296 2 жыл бұрын

Does there any lpg conversion kit exist ore adapter ? Ore propane conversion methode?

@chrismurphybiz 7 жыл бұрын

I just had one question. I just wanted to ask re the fuel isolation valve, I've tested this, it's clean, it clicks when I put a 12V charge acrosss it but I wondered, should the 4 holes in the valve all be completely open and exposed when you put that charge across or do they still appear partially 'blocked'. It clicks which is good but not sure how far it should go back so not sure if it is still faulty. Any ideas, thanks :-)

@JamesAkers 7 жыл бұрын

Hi Chris. I've just checked my ones and yes, you can still see the pin through the holes so it's not completely open. Hope that helps. James

@chrismurphybiz 7 жыл бұрын

Great, thanks James, really helpful.

@speedy9able 3 жыл бұрын

Hi can you tell me is this carb for golf2 1.3 pleasse

@tonylivesey7879 5 жыл бұрын

hi great vid, hoping you could help me, i have a issue with the fuel returning to the float chamber via the top hole in the pump and none coming out of the pump injector when trying to measure ml per stroke, its puzzling me.

@JamesAkers 5 жыл бұрын

Hi Tony, sounds like the injector may be blocked? Can you move the ball bearing in the bottom at all? I might have a spare knocking about if you need it.

@tonylivesey7879 5 жыл бұрын

Hi, james i was thinking the same myself, i can move the ball bearing but it is very stiff and jerky and i can only just blow down it, if you have a spare that would be great let me know how you would like paying as i have looked but can not find a replacement. Thanks Tony

@tomken18 6 жыл бұрын

Hello James. I need the little black round heater that is fit to heat the throttle Valve. Do you know where i can buy iT.? Or do you have a spare to sell.? Thank you.

@JamesAkers 6 жыл бұрын

Hi Tom, I might have one. I'll have a look this weekend and let you know. James

@tomken18 6 жыл бұрын

Ok Thank you.!!

@Saxonx500 3 жыл бұрын

Did you use a sonic cleaner in the end?

@JamesAkers 3 жыл бұрын

I had a go. It was going well until it just stopped working so can't really give a good answer. The paintbrush works really well to clean the outside.

@smallweights 7 жыл бұрын

hi james in the Haynes book t has the specs for the peirburg 2e3 for the vw lt 2.4, would you be kind enough to post the specs up, I have used your videos to rebuild my carb but I cant get a manual for the specs, you know the specs for the accelerator pump and choke flap, you know where you used a drill bit, I am struggling to find the specs for the LT want to get my carb back on and the van running

@JamesAkers 7 жыл бұрын

Hi mate, the Haynes I have has the following info for the LT 2.4 - There are two measurements for the Choke pull-down: (a) - 3.5mm +/- 0.15 and (a1) - 7.2mm +/- 0.2. If you look at this video for the Golf the guy makes two measurements so it might be the same process for yours: kzfaq.info/get/bejne/qNpnn8JzlrCZZIk.html No info on the pump setting though, i'll see if I can dig anything out.

@JamesAkers 7 жыл бұрын

Also, jets sizes should be 107.5 and 135.

@smallweights 7 жыл бұрын

top man, thank you James really appreciated, I guessed it was around the 3.4-3.5 for the choke I set mine at a "slack" 3.4 so is probably 3.5 so really chuffed, surprisingly easy carb to do once you get into them, look complex at first with all the vacuum lines etc etc but once the screws are in done, they are not to bad, your video certainly help so hi5 from me to you!

@smallweights 7 жыл бұрын

excellent really appreciated james! I found it hard to find the settings for the LT petrol, a lot of info is in Russian, I don't think the pierburg had much love in the uk, they seem pretty good to me if set correctly, simple like an SU used on BL/Austin engines