Leaking pinion seal on a 2005 Ford Crown Victoria.
Пікірлер: 22
@1995flyingspur3 жыл бұрын
This guy is an obvious pro... But I'd recommend an inch torque to check the preload before and then using that inch torque when going back on, maybe adding five extra inch pounds for drag. He obviously doesn't need to, just saying for those of us who aren't that experience.
@billgator20053 жыл бұрын
man you can service my vehicle any day. shame all mechanics don't work with such skill...thumbs up!! it's a pleasure to watch you work...
@raincitywrench1173 жыл бұрын
Those are kind words. Thanks for watching!
@MrTA-cq5bk2 жыл бұрын
Thank you for sharing your video. Very helpful! 👍
@Bill-ts9zv3 жыл бұрын
Learned a lot, good job
@4g63justin3 жыл бұрын
Good quality work 👍
@gregbennett42548 ай бұрын
I would still use an inch pound to get a reading to compare
@luxuryacuraz3 жыл бұрын
Great Video
@RoRo-kc8zv3 жыл бұрын
Mat makes it look easy FYI wrenching is tough , but I bust tires mostly but the mechanic at my shop let’s me swap parts when he’s busy so my point is experience is key! Ps love this channel
@raincitywrench1173 жыл бұрын
How's it going Ro Ro? Been a while. Keep grinding away & someday you will be the guy with all the experience.
@paulkeene54299 ай бұрын
Very very good video,mmechanic told me its a four hour job! BS eh?
@kevinavery25183 жыл бұрын
using a kent-moore tool on a ford, rotunda is gonna be mad.....lol, and mark, well mark is one heck of a guy, i consult him allot, everyone should, good video RCW,
@raincitywrench1173 жыл бұрын
Yea, Mark has never let me down. It's Murphy you have to watch out for, seems like he's always around. Karma can be a real jerk sometimes. Haven't seen it yet but was told the main shop has a new "powertrain lift" for the mustang mach-e batteries. Ford makes dealers buy it before they can sell them. Think it's a big scissor lift with a table on top. I suspect rotunda makes that also or is the middleman.
@kevinavery25183 жыл бұрын
@@raincitywrench117 we have one of those lifts at my Chevy dealership, had to have it for doing the battery packs in our Volt's, also makes life easier when you're dropping complete cradle, engine and transmission assemblies all at once
@raincitywrench1173 жыл бұрын
@@kevinavery2518 Yep, same here. The dealer has an otc scissor lift but I think this new one is the size of a pool table.
@kevinavery25183 жыл бұрын
@@raincitywrench117 dayum.....lol
@broken19652 жыл бұрын
Why not pull out slinger and bearing inspect for pitting
@raincitywrench1172 жыл бұрын
The outer bearing has a slight interference fit on the pinion shaft and in most cases can't be separated unless the pinion gear is smacked out. So if the rear end isn't making noise then I don't inspect.
@712gln3 жыл бұрын
are you on the ford tech forum on facebook
@raincitywrench1173 жыл бұрын
No. Can't remember the last time I have been on facebook. Turned all my notifications off. I dedicate all my time to KZfaq. Just may get on and check it out this week. Thanks for the tip