Make sure to warm up your cans in warm water and make sure you fully wet out the last few coats if you want to get rid of the textured look you ended up with. It should come out fairly smooth when done right. Definitely a cheap mod worth doing that looks good.

This is very cool! Years ago I was hand polishing my chrome emblem. I was trying to make it super shiny. Just by hand, I wore a spot thru the chrome. I had to continue to polish to remove all the chrome. That’s how I discovered blackout emblems. Seriously it did look good.

i just did this to my silverado. i didnt want to go buy new black emblems again so i did this. And its been worth it. Even if you have any "over spray" I used some hand santizer to rub it away and then sprayed the spot down with some warm soapy water to ensure the alcohol from the hand sanitizer didnt harm anything

Pretty cool. This will give the guys and gals a good project to do alone or together while locked up at home for weeks and months. This is a very sharp looking finished product. Thx for letting us watch.

Thanks, bud. I wanted to change the emblems on my F150, but this makes so much more sense. Gonna give this a try.

Just did this on my 2008 mustang GT and it looks great, thanks for the video my friend

Too cool. I have to try this method. Thanks for sharing. 😉

Just did this to my Toyota. Absolutely wonderful!!!

I've used plasti-dip for many many projects and this method really surprised me! Very nice results

Pro tip: put a very small piece of tape on paint, in between outside of H and inside of circle around H, so you don’t have to scrape a hole through the plasti dip to start the peel. You can take that piece of tape off, and there is a nice little uncovered spot you can start peeling from

Thanks to your vid, I did this to all 3 of my cars. One note, the 'O' and 'D' in Odyssey are a pain to fix if you don't plan ahead and stick a little tab inside for peeling afterwards.

Best window tinting idea 💡!!! Thanks 🙏

Did this on my civic and it went perfect! Thanks!

Thank the wife for us on the great camera angles. Thanks for the video!

I did my marker lights, nice tint and still looking good 6 years 65k miles later 👏

Looks great, going to try this on my civic 😄

Amaziiiing!!! I'm gonna try it , but with pink color yeyyy!!!!

Finally someone that knows to spray paint in a sweeping back and forth motion while stopping at each end. It's unbelievable how many videos there are of spray paying on KZfaq where people don't get this extremely basic technique. Hell it even says it on the damn can.

Wow, that looks cool man. I didn't realize using that stuff was so easy.

Excellent job thanks for posting it!!

Good video man! Just did my Jeep a couple weeks ago and I'm super happy with this stuff.

Awesome project, also good comment helpful tips.

Oh wow. I thought I was the only one. I black plasti dipped my rear emblems and white on the front. Looks really good. White Accord Coupe 2014.

Just finished on my Tacoma!! Only ones I had to do were the TACOMA badges on my front doors....chrome....ICKY. Followed your recipe & WABAMM!! Thanks man!!

Thanks for the vid! Commenting for the algorithm.

lets go! best video on youtube for this man deserve a sub! keep it going

Cool, thanks for posting!

a tooth pick works really well to get clean edges

I did my front and rear emblems red to match my skirt pinstripping. It was so easy and was done in an hour

I've always thought those chromed plastic names on cars looked so tacky, making them black like that does make them look a bit better, but I just got the Ford Maverick and I'm glad the name is imprinted in the tailgate instead of just having those plastic letters stuck onto it... Thanks for the video, I'll probably find something to do this with, lol.

Cheap, easy, and worth it every time🤙🏾

Wow man you saved me so much work 😅

Finally a video with no BS

Muito bom amigo, é o melhor vídeo explicando de forma didática. Obrigado! 🇧🇷

Painted it too, very pleased

Nice job, but I would personally debadge the Civic badge and just keep the H emblem in centre blacked out.

I suggest you use clear coat after you've done all of your layers. I did this to my car on the emblems and it came out really clean + it protects the plasti dip

This is the right Way!!!!! Thanks

I wish would be as simplistic as this video best video eva

Nice job! How long does plasti dip last? Can i use it on the windows chrome trim ? And last how about spraying clear coat on the top before peeling , brand new car i really wanna do it right thanks in advance.

Thanks for the video, need to redo my front emblem. Hello from down the road in Olathe.

Doing this tomorrow on my day off!!!

great job 🤜🏼🤛🏼

Damn wish I would of seen this 6 tries ago! You made it look so easy imma redo mine so 7th times a charm lol

Looks simple sweet

I won’t be doing this, but smartest way to do this I’ve seen

I want to try this on my BMW 135i. I think I might try it on my Chebrolet Spark first though. Lol!

Nice mod, thank you! Greetings from Siberia, Russia =)

Read tons of comments and not a single person here seems like they’ve painted professionally. I watched your video for 5 seconds and can already tell you a HUGE no no that you’ve done before painting. NEVER use cloth that is dingy and falling apart to prep your painting surface. You risk whatever dirt/debris is caught in the strings being left behind on your prepped surface. You also risk leaving behind stray strings/threads that you wouldn’t notice without a thorough inspection. You can see thread caught under the plastidip in the before and after transition photos/videos. Sprayed paint unfortunately magnify whatever is caught underneath and only gets worse upon adding extra coats so it’s VERY crucial nothing stays on the surface and nothing lands on the surface while curing. Outside of that, your technique is great.

This needs more views. Nice!

🙋‍♂️ loved the work. I have a few questions ??? Are all the four coatings 30 mins spaced? Is it just the plastidip can needed to do this or do i need to buy primer or anything?

Mine did not pull away like that. It acted more like regular paint. Had to use a plast tip to get the access off. Scratch part of the car. However I used a different brand this time.

Great video! Did you use pure rubbing alcohol or dilute it with water to clean the areas/what ratio if so? Did you use 70% or 90% isopropyl alcohol?

Dope

Too cool but what kind of spray did you use on your car

Other people say to add/mix products do/should I need to? I know you only used the spray but does it help or hurt paint less when mixing somthing with it?

Brooooo this is Great

Nice video! thought about doing this and it honestly doesn't look bad at all. Looks like a nice alternative to save money if that is your goal. But I think I will spend the $$ and get the OEM gloss black emblems for my 2021 accord sport 2.0

Great video 😊

Incredible

Man the previous owner of my car did this and when I removed the badges I could see where he ran the razer through smh. Don’t use to much pressure guys (obviously). Or just try to cover as much area as you can with the tape before you spray (put tape between letters, inside the letters, around the letters, etc..) so that you won’t have to use the razor.

I used Plasti Dip to make my shiny white security cameras matte black. It's good stuff.

Can you plasti dip the emblem on the steering wheel airbag cover without harming the cover finish? 2020 Honda Fit

One question. Is it gonna stay after i use brush on the carwash for that element ? Or sponge ? Is it easy to take it off?

nice job

Thats an amazing video. My problem is that i want paint a color by each letter which i needed to buy 4 spray 😅

thats dope, thanks

Body shop tip put newspaper on hood. Tape edge remove it from the hood and place where you want it.

this is the most honda civic mod ever i love it

How long does this last?

Hi, did you have to blade around the lettering before peeling off the excess?

I think this would easily peel off dont you think? Like peeling around what you did. Might do it to my Toyota Celsior.

How long do you have to wait after spraying the last layer before pealing it off the paint?

Another easy way to get the plasti out of the holes of the badge is to use a toothpick

great video, did you wait for it to dry to remove the newspaper and tape or straight after the last coat?

Did they have a variety of colors for the spray plasti stuff? I’m really wanting to do baby pink on my black civic hatchback.

Honda wanted 110$ for blackout badges. This is definitely the way to go.

did i miss plastic dip parts? how did u pit it ???

Nice 👍

How long will this last usually? I'm assuming it'll wear off quite quickly if you wash your car often?

Does the plasti dip start peeling off overtime? If it does any idea on how to make it last longer?

Great👍🏻. How much this plastidip long last on the emblem with the color without fade off?? I want to try it.

Nice work! What is the name of the sound track ?😅

If you wanted to spray a clear coat of plasti dip over the black to give a high gloss would you do it after you have peeled the black or before?

Nice tutorial dude...

Do you have to put anything on the badges before that? Like plastic on top of the badges? I’m new to this I just don’t want paint on my actual car

Thanks for video! Where can I buy that spray at ?

Nice job good video

Durooo 💪🏽💪🏽💪🏽🔥🔥🔥🇵🇷🇵🇷🇵🇷

Do you think it works for door handle?

Is it durable and scratch resist ? want to black out my door interior panel and center console ,which is beige in colour and its plastic.

how long do they last after applying the paint? does it change color or get affected by UV?

why is the spray not loosing its strong hold on the letters but only on the car ? Do you have to use a kind of knife around the letters ?

But how does it stay on the letters, even around the edges, and not peel off? Do you apply something to the letters and not the paint? Or vice versa? How do3s i5 not peel off the letters? Or do you use an exact knife and outline every letter?

How good is it when it comes down to washing your car, does it last long?

Is plasti dip durable? If it comes off the body of the car so easily, will it come off the emblems/logos just as easily? Like will it be durable in car washes? Or is this something that has to be done periodically?

I have a 2022 Honda Civic and I want plasti - dip the wheel center caps H emblem in red. How would you go about that?

Very nice

Great video! Quick question, why 30 minutes between spray coating?

What plastidip brand did you use?