It's working again! It was the little filter on the inlet. Thank you for the extremely helpful video👍
@pistolasnine83899 ай бұрын
Thank you! Great video and instructions 👌
@user-xy4oy9xl4o6 ай бұрын
Great Video. I now know what I need to do for the maintenance of my Rheem Tankless heater.
@PlumbingSolutionsLLC6 ай бұрын
Glad it was helpful!
@quangvu44494 ай бұрын
VERY INFORMATIVE... THANK YOU VERY MUCH!!!
@MzladyGrinn Жыл бұрын
This video has been a big help for me! Thank you, so much!
@kelseybone31144 ай бұрын
Any suggestions on how to fix a fill error on a ruud combi boiler?
@steiner1942 Жыл бұрын
Really Good. Have a Navien and it just went dark on me. No power to controller. Slight drip from actual Water heater outer casing!! Unplugged, going to open it and see what is leaking, possibly fried the unit?
@jap44999 ай бұрын
Hello did you figure out what the issue was to the controller?
@wackyfours Жыл бұрын
Sweet
@amandaturner1114 Жыл бұрын
What about this water heater not turning on at all?
@UncleSamSpeaks2 ай бұрын
Thank you!
@timbrowning68226 ай бұрын
We have a Rinnai that from time to time stops working after a few minutes. We have no codes and it just reads the 120. It doesn’t happen all the time. We also just had it serviced and the tech said he couldn’t find anything wrong. Any suggestions what our problem is? Thanks
@PlumbingSolutionsLLC6 ай бұрын
Water savers in shower heads, something is slowing the flow,
@joeorlando948 ай бұрын
Mine - the pressure regulator for the natural gas was stuck. Just tapped the regulator with the handle of a screwdriver and the water heater fired up.
@PlumbingSolutionsLLC8 ай бұрын
surprisingly that has fixed the problem for me so many times .
@FlawlessNavi Жыл бұрын
I get Code 12, P1, 12, then P1 again. Any idea what that could be?
@PlumbingSolutionsLLC Жыл бұрын
I'd say water savers in your shower heads. Code 12 is a flame out. It was burning then it quit. P1 is low water pressure. So, something is restricting it. check the filter on the bottom of the heater too.
@DiegoPerez-hh2sz2 ай бұрын
How about error code 52? It says something about checking the harness for the solenoid.. but what is the solenoid.
@PlumbingSolutionsLLCАй бұрын
It's the gas valve. those don't normally go bad. probably got some corrosion on the connection, unplug it and plug it back up..
@melissadee3 Жыл бұрын
What about 29? Can I fix it?
@PlumbingSolutionsLLC Жыл бұрын
That a condensate code. check the condensate drain line.
@VladRonin3 ай бұрын
Thank You for video. I have Eccotemp 45 hi - natural gas water heater . Have code E 3. All is OK. Water pressure, gas, vent is clean .. HOW to reset that code.. I Turned OFF power for all day, dont helps. Thanks
@PlumbingSolutionsLLC3 ай бұрын
Um, normally turning the power off for a few seconds does the trick. Eccotemp has a tech support number you can call, it's probably really simple.
@VladRonin3 ай бұрын
@@PlumbingSolutionsLLC I DID BEFORE MANY TIMES. Heater was Off all nigh, but stil coming E 3 Code...
@daleadams9323 Жыл бұрын
what is code 24?
@PlumbingSolutionsLLC Жыл бұрын
that is a bad remote or remote wires
@user-rs8zi4gw8l10 ай бұрын
What is code 1L
@user-ti5vs3is6n7 ай бұрын
How about error 14
@jeanne65614 ай бұрын
What does code 13 mean?
@PlumbingSolutionsLLC4 ай бұрын
Indoor unit code normally means you got something in your venting. like bugs or some bird is trying to build a nest. check your vent .
@timbrowning68226 ай бұрын
We have removed the water savers in the shower heads
@PlumbingSolutionsLLC6 ай бұрын
Did it fix the problem?
@timbrowning68226 ай бұрын
It worked for three showers. The water starts hot for about five minutes then goes cold. Then the next day the shower stays hot?I think my tankless is bipolar?