Adjusting your TPS on the PRO RMK is a pretty easy process, and it can make a great difference in how your sled runs. Give it a shot!
Пікірлер: 58
@matthewthayn47144 жыл бұрын
This was very helpful! I have a 2013 Pro that I just replaced the motor in and it wouldn't idle very well. I followed your steps, used a little bit of common sense, traced wires because my TPS plug was different and made it work. The general idea you showed was the same. Thank You for saving me $200 of shop charges and teaching me another useful skill!
@xboyys11232 жыл бұрын
I have a 2013 too and I can’t find the tps wire
@califritz2 жыл бұрын
What wire on the ecu do you power it up on ?
@raimylang4 ай бұрын
Grdd we at video helped me set my tps on my 2005 sportsman 800! Thanks
@mitchschwab2253 Жыл бұрын
I just bought 2 2016 axys 800s for a killer deal - both have less than 1500 miles on them. One of them has a super low idle on start up to the point the screen flickers and it wont go into reverse. Gonna try this out and see if it resolves the issue
@ianmcnichol11112 жыл бұрын
What connector you using to power the ecu ? Which wire or Color wire you put the pin in to read the voltage ?
@teriferguson85875 жыл бұрын
Your the MAN!! searched and searched and no info on this topic until you posted this very informative video!!! Thy symptoms you talked about is spot on!! The piece of shi$ dealers charge you an arm and a leg or two to replace all kinds of parts trying to figure out this mess!! Thank you for your time and information it saved me! Pun Intended!!
@mutt2jeff5 жыл бұрын
Glad it worked out for you 👍
@denseleit Жыл бұрын
Thanks bud. My 16 800 is taking more pulls to start and dying after 30sec and running good after the 2nd start... Probably tps is out.
@tobyemond2 жыл бұрын
I have a question, I did everything in the video with the set screw not touching the throttle cable and got to .7000 but after tightening the set screw it only lowered my milivolts? I then tried to put the set screw all the way in so the throttle cable was slack and it just made my millivolts go down to .2000 and the highest it would go is .4000 please help!
@Rickydbaby Жыл бұрын
Just attempted this the other day. My TPS was at .711 and idle set to .928 if i set to .700 and .940 my sled will not idle down below 2200-2300rpm. I reset it back to .711 and .928 and runs great and idles at 1850rpm.
@thomaskilligvuk1124 Жыл бұрын
I had to change left side piston and the power values an it's has two idles for the throttle by the handle bars an then by the engine
@skogquistcompaniesinc.728 Жыл бұрын
I did all of this to the T. And I’m still having a low idle problem. Any suggestions.
@clarencesnyderjr95473 жыл бұрын
On my tps tool I put it at 7000 do I set it at a different setting?
@sleddersofnl23025 жыл бұрын
Are you using 12v DC or 12v AC
@Demopgarage3 жыл бұрын
would this be the same for the 2011 assault 800?
@private_noob8449 Жыл бұрын
Does this method work on all sleds?
@derekjones65404 жыл бұрын
Do you have to remove the secondary to get to the TPS to adjust?
@thomaskilligvuk1124 Жыл бұрын
600 2012 polaris pro r high idle
@clarencesnyderjr95473 жыл бұрын
What do I set my tps at with my tps tool?
@jakeanderson48254 жыл бұрын
I have a 2009 assault, fresh rebuild, everything new. Put 80 miles on yesterday, starts on 1 pull, idle is perfect, throttle response below 6000 rpm is good, anything over half throttle it bugs down. Could this be a tps issue and is it worth monkeying with it if the idle is fine?
@doobyboy214 жыл бұрын
Did you figure it out ?
@isaaccollura664 жыл бұрын
My 2013 pro is bogging only at full throttle too. Cuts in and out at full throttle. Seems fine below full. Let us know if you better figured!
@bradq7693 жыл бұрын
@@isaaccollura66 any luck?>
@insidelinemx3 жыл бұрын
What is the idle rpm you’re looking for?
@jdorney703 жыл бұрын
I'm having a similar problem with my 07 iq touring 600 cleanfire. Would the tps affect reverse as well? I have to bump the throttle to about 3k for it to engage.
@crazywormy58692 жыл бұрын
Did you figure this out
@dravenallen045 жыл бұрын
Is this the same for 2012? Are theses specs from Polaris?
@darrellmarthaller93773 жыл бұрын
I’m hoping you can help me. I did everything in your video when I went to start my sled it idialed to high, I went to shut off my sled and I would not stall. I could not shut off me sled? Kill switch or key will not shut off my sled. Any tips ?
@Dawson55893 жыл бұрын
Oh shit hopefully it doesn't go that way for me
@joshrowden17503 жыл бұрын
Let me know out come please. I havnt touched tps but my kill switch somtimes won’t shut off
@tystensland2044 жыл бұрын
What year is this sled
@ryonbowler65513 жыл бұрын
Do you have any information on the adjustment of the Phillips or zero offset screw?
@monteturre45678 ай бұрын
2.5mm Allan and 8mm wrench
@kylescott80825 жыл бұрын
Could you just start the sled to power the ECM ? I’m having some idle/bogging issues on my 2014 pro as well and I’m going to give this a try.
@mutt2jeff5 жыл бұрын
No, you need consistent power supply, and you will probably kill the sled while moving the position sensor
@cassidystrickland25574 жыл бұрын
Just turn the key on and dont start...it will give you the 5volt reference. Probe the sensor wire and you can ground your negative lead of your meter on any bare metal surface
@darreningleson12614 жыл бұрын
Cassidy Strickland If your Rush is a pullstart you won’t get the 5VDC as it has no battery.
@cyrilandrews76575 жыл бұрын
Well this apply to a 550 Polaris adventure???? Thanks
@mutt2jeff5 жыл бұрын
No idea
@daverabe2293 жыл бұрын
I have a 2013 pro and the engine light goes of and on with the code 520 194-3 which I learned it meant high voltage with the throttle and I’m really confused how to fix it bc it’s a small problem that puts the sled in limp mode and I can’t even drive it when it happens!!
@manitobatv293 жыл бұрын
Having the exact same problem were you able to fix it??
@daverabe2293 жыл бұрын
@@manitobatv29 yesssir, so basically I just bought a new throttle box with all the wires and stuff and I put it on and it works great hasn’t went into limp mode so far. It’s not a big problem so don’t worry about it.
@manitobatv293 жыл бұрын
Dave Rabe thanks for the reply! Will take a look at it
@bbbfingerboarding3 жыл бұрын
Have the same issue with my sled currently runs, but acts like it has a rev limiter right before the clutch engages so it can’t move! Did you replace your whole throttle assembly??
@daverabe2293 жыл бұрын
@@bbbfingerboarding yes, everything except the throttle cable
@FabbroTV5 жыл бұрын
I just tried this. Now my sled won’t start at all... is it possible to ruin the ecm by doing this process?
@ethanwilson90085 жыл бұрын
I have a 2012 rmk and can’t seem to find the connector to tap into, how do you locate it?
@mutt2jeff5 жыл бұрын
Easy way is to start at your TPS and just follow the wire up. It's gotta go somewhere!
@ethanwilson90085 жыл бұрын
mutt2jeff very true, will give it a try. Video was very helpful!
@mutt2jeff5 жыл бұрын
@@ethanwilson9008 make sure you check to ensure your TPS voltages are the same for your model year of sled, I have seen some different numbers out there for earlier sleds.