Small Block Chevy Build Stage 2, Part 2: Complete Assembly & Dyno Day

Small Block Chevy Build Stage 2, Part 2: Complete Assembly & Dyno Day - Engine Power S3, E3

Рет қаралды 552,470

5 жыл бұрын

Completing the small block Chevy with trick induction from the heads to the intake manifold. This potent combo makes big power on the dyno.
Air Flow Research: Cylinder Heads, Eliminator, Aluminum, Assembled, 75cc Combustion Chamber, 220cc Intake, Chevy, Pair
More Info: pntv.us/pn_pt_12016
Air Flow Research: Intake Manifold, Titon, Street/Strip, Plastic, Black, Single Plane, Square-Bore Flange, SBC Chevy, Each
More Info: pntv.us/pn_pt_12015
Air Flow Research: Carburetor Spacer, 4-hole, Phenolic Plastic, Black, 1.00 in. Thick, 4-Barrel, Square Bore, Each
More Info: pntv.us/pn_pt_12019
Air Flow Research: Carburetor Spacer, Open Style, Phenolic Plastic, Black, 1.00 in. Thick, 4-Barrel, Square Bore, Each
More Info: pntv.us/pn_pt_12018
Cometic Gasket, Inc.: Head Gasket, MLS, 4.100 in. Bore, .027 in. Compressed Thickness, Chevy, Each
More Info: pntv.us/pn_pt_12017
Design Engineering, Inc. (DEI): These Design Engineering Protect-A-Boots keep your plug wire boots and wires safe from header and exhaust manifold heat, lowering the risk of backfiring and engine damage. Guaranteed up to 1,200 degrees, they fit most straight or 90 degree boots
More Info: pntv.us/pn_pt_12024
Doug's Headers: Headers, Tri-Y, Steel, Ceramic Coated, Chevy, GMC, Car, Pickup, 283-400, V8, Pair
More Info: pntv.us/pn_pt_12011
E3 Spark Plugs: Spark Plug, E3, Tapered Seat, 14mm Thread, .440 in. Reach, Projected Tip, Resistor, Each
More Info: pntv.us/pn_pt_12010
Holley: Carburetor, Street HP, 4150, 4-Barrel, 650 cfm, Double Pumper, Mechanical Secondary, Universal, Each
More Info: pntv.us/pn_pt_12009
Intercomp Racing: Torque Wrench, Digital Calibration Tester, 0-200 ft lb., 1/2 in. Drive, Converts Ft lbs.to In lbs., 9 Volt
More Info: pntv.us/pn_pt_12026
Jesel Inc.: Rocker Arms, Shaft Mount, 1.6 Ratio, Aluminum, Full Roller, Chevy, Small Block, Victor Jr., E-Tec Heads, Kit
More Info: pntv.us/pn_pt_12014
MSD Ignition: Distributor, Pro-Billet, Small Base, Magnetic Trigger, Mechanical Advance, Chevy, Big/Small Block, Each
More Info: pntv.us/pn_pt_12022
Quick Fuel Technology Inc.: Carburetor, Black Diamond Q-Series, 950 cfm, Mechanical Secondary, 4-Barrel, Square Bore, Drag Race, Each
More Info: pntv.us/pn_pt_12021
Royal Purple: Motor Oil, XPR Racing Oil, Synthetic, 5W30, Quart, Each
More Info: pntv.us/pn_pt_12005
Summit Racing: Cylinder Heads, Aluminum, Assembled, 62cc Chamber, 170cc Intake Runner, Chevy 1987-95, 5.7L, Pair
More Info: pntv.us/pn_pt_12007
Summit Racing: Engine Block, Cast Iron, 4-Bolt Mains, 4.030 in. Bore, Clearanced, 1-Piece Rear Seal, Chevy, Small Block, Each
More Info: pntv.us/pn_pt_12006
Summit Racing: Engine Block, Cast Iron, 6-Bolt Mains, 3.780 in. Diameter Bore, Chevy, 4.8/5.3L, LS Gen III, Each
More Info: pntv.us/pn_pt_12023
Summit Racing: Combo, Summit, Water Pump, Electric, Aluminum, Natural, Chevy, Small Block, Relay, Kit
More Info: pntv.us/pn_pt_12004
Weiand: Intake Manifold, X-CELerator, Single Plane, Aluminum, Natural, Square Bore, Chevy, Small Block, Each
More Info: pntv.us/pn_pt_12008

Пікірлер: 420

@PowerNationTV 5 жыл бұрын

Subscribe to PN+ at the link below and receive the first month for just 99 cents: httpslink.com/lnk_3d0d9e0c

@normhodgkinson6965 5 жыл бұрын

so, what was the HP with the 3 inch exhaust ?

@mdbadalmiah6808 5 жыл бұрын

Thank you sir 🇧🇩🤝

@mdbadalmiah6808 5 жыл бұрын

Please engine fiaring mark and timing mark setting thank you sir

@YoungerPrice 5 жыл бұрын

Probably 10hp

@rggt6225 5 жыл бұрын

Can yall build a DOHC Ford engine

@liberatorkramit 5 жыл бұрын

I feel like a crazy person. I rip engines apart all day for work. Then I come home and just watch engines get ripped apart and go back together.

@dmpl92 5 жыл бұрын

No worries I am in the same boat. My gf thinks I am crazy.

@liberatorkramit 5 жыл бұрын

@@dmpl92 Well, I guess it's good to know we're not alone in our crazy. Lol.

@wyndnra1n 5 жыл бұрын

If you like what you do, you don't work a day in your life

@liberatorkramit 5 жыл бұрын

@@wyndnra1n well that's just blatently untrue. I love what I do. It is still work. I still work by others rules, at a chosen pay by someone else, with people I don't like. It is a great sentiment. It's wrong.

@DrumToTheBassWoop 5 жыл бұрын

Daiten Lowkie Engine addiction, happens to us all. A fairly menial machine that fascinates the most interested minds.

@johnmcwade222 5 жыл бұрын

About time someone made a plastic intake for the older style engines like they have for LS motors, the weight saving.

@bilbobaggins4710 5 жыл бұрын

And won't heat soak like metal intake

@TejasToolMan 5 жыл бұрын

exactly!

@nobullshit9721 5 жыл бұрын

Yeah I guess but I think I just like the classic look of an greatly machined aluminum intake not some black plastic stuff

@bilbobaggins4710 5 жыл бұрын

@@nobullshit9721 yeah

@alexcorona 5 жыл бұрын

John McWade aluminium Manifold barely weigh 10lbs

@numinous4789 5 жыл бұрын

"No cutting corners on spark plugs" ... (then proceeds to install gimmicky plugs - from a sponsor, of course). LOL!

@edwardmyers1746 5 жыл бұрын

E3 lol

@Trigger_32 5 жыл бұрын

Yeah but E3 came in and proved that their plugs are better with "their computer" lmao

@numinous4789 5 жыл бұрын

@@Trigger_32 Indeed. I'm sure they're VERY unbiased about their own plugs, LOL

@nbrowser 5 жыл бұрын

Yep....and no matter what I've done in my shop...it seems GM engines absolutely LOVE GM plugs...just works perfectly.

@kenshinhimura9387 5 жыл бұрын

@@nbrowser GM doesn't make spark plugs....

@CanadianDerwood 5 жыл бұрын

Great explanation of the importance of proper torque! I gotta say I love your show. I'm a long time viewer of the program. It all started back in the times of network T.V. I watched the first episode when I was a teen. I'm now a Licensed mechanic. The knowledge I have gained from watching has given me an edge on in may career. Now my 5 year old watches the show with me. Thanks to RTM for keeping the show going, everyone involved are Legends in my life! Keep up the awesome job!

@israelaguilar2896 2 жыл бұрын

Torque specs are so important. You guys don't disappoint. Glad to know you.

@HeavyJ318 5 жыл бұрын

Thanks for putting this up here for free! I kinda wish Joe was my grandpa

@Tango0287 5 жыл бұрын

This 383 is almost identical to my old 383 set up. Same heads and intake but with comp cam XR292r in mine (254/260 612/618 lift 110 lsa) and 750 carb. Interesting to know what power it was making. Looking forward to the part 3 of this to see if its anything like what im building now. Im now building a new short block for this top end to go on. Its a dart little M with a 3.8 inch stroke and 4.165 bore to make 414ci. Hope to make 600hp.

@michaelphelps5064 4 жыл бұрын

Sir I believe you will!

@bradwilliams4921 3 жыл бұрын

Amazing the detail that goes into assembling an engine.

@mr.blonde1709 5 жыл бұрын

LOVE this series. thank you, bros.

@CamaroRick 5 жыл бұрын

Good to see Joe on here. Takes me back. Ive never heard of those polymer intakes up until now. The design is pretty cool

@tomrose6292 3 жыл бұрын

The intakes are nice I know a couple guys that's running them on street rods.they said they noticed there engines improvments.i couldn't tell tho they were still in my rear view mirror ..lol

@yourfavoritelawnguy2722 4 жыл бұрын

I know this is just a 20 minute Ad, but i cant stop watching them

@lawnmowerdude 5 жыл бұрын

The main reason I clicked on this video was because of the plastic intake manifold. Nice to see something different.

@rafihussain 5 жыл бұрын

Great stuff. Nice for jobs and business. And specifically for talented ppl like u. Thanks

@mitch_smith Жыл бұрын

I miss seeing old Joe drop in on the shows. Feel like I watched him most of my life.

@Bobthebuilder.69 29 күн бұрын

Sadly, he's no longer with us now. I came to watch and reminisce.

@pablocespedes9585 5 жыл бұрын

Thanks, I really learned good stuff with your videos!

@Estoooopid 4 жыл бұрын

You guys have best job. Lots of hard work im sure

@generalrobinson8637 5 жыл бұрын

Those are some huge heads for that 383.

@heathwoodlee520 5 жыл бұрын

Absolutely loving the tech talk here! No gimmicks, real science!

@tclott316 4 жыл бұрын

Heath Woodlee you’re funny

@heathwoodlee520 4 жыл бұрын

Thank you

@futten3230 5 жыл бұрын

where did the 8000 rpm go?

@JayAR_YT 5 жыл бұрын

scared

@demarques1911 5 жыл бұрын

Bolts and pistons would've been all over the floor😅😅😅

@kramnull8962 5 жыл бұрын

@@demarques1911 balance and blueprint...

@michaelnelson1560 4 жыл бұрын

They may have built the engine to run up to 8K, they quickly found out that 6500 is the peak HP, no need to twist it higher

@sarahvassallo9029 4 жыл бұрын

Carb is wrong size then

@dilldowschwagginz2674 4 жыл бұрын

One of the best things about watching engine builds (other than the great content) is that KZfaq doesn't even bother forcing me to watch Bloomberg ads!

@dwightschrute3862 3 жыл бұрын

Now I get car insurance ads that are like “car dealerships will hate you for the trick I am going to show you” no one is falling for that besides old people which I guess is their target demographic

@brian5606 4 жыл бұрын

Man, you guys are marvelous. I'd like to see a stage 2 built up using Edelbrock's twin carb tunnel ram intake, either one will would, either the victor or the older version. I'm building a 9500rpm 3.000" stroke with a 4.03 bore block like you've used here. I might use the dart 4.5 bore spacing block rendering the use of 4.250" bores to un-shroud bigger valves making my combo easier to get the rpm I'm after. There's way good valve train assemblies available today to make a high-rpm unbelievable sounding small block chevy. High Horsepower isn't mandatory in my application, coolness of sound is in my 37 chevy pickup build is. In my application coolness rocks and this little small motor is just what the doctor orders. You guys are the bomb. 💥

@jasonschagt6527 5 жыл бұрын

Nice build. I would've tried a set of Brisk spark plugs, set of step headers and a old school velocity stack.

@fireblaster5181 4 жыл бұрын

Lmao Love the ending there. "Peace"

@randalltufts3321 5 жыл бұрын

Friend: "consistency is built on teamwork & determination". Me: "you forgot the most important thing, 💰 money. Patience weedhopper.

@lewissilvio4740 5 жыл бұрын

Awesome video guys

@RX7GSLSEowner 4 жыл бұрын

Great to set Joe again!

@jonathanthomsen7218 5 жыл бұрын

These guys need to watch engine masters and learn from the trio

@alexcorona 5 жыл бұрын

Jonathan Thomsen These guys build engines to sell product. It's literally their job.

@skylinefever 5 жыл бұрын

@@alexcorona Exactly. Some people win the Engine Masters tournament by using OEM parts in engines that were never designed to take them. You can find strokers that used Chevy connecting rods in MOPAR and Pontiac engines for example.

@matthewgorgoglione5492 5 жыл бұрын

That's awesome, how come there's not just a complete package on this? My garage project would be complete finally 🤗🌴

@NorthViewModelShop 5 жыл бұрын

I wouldn’t put E3 plugs in my ex’s wife’s new husbands lawn mower.

@onlylikenerd 5 жыл бұрын

Why

@alexcorona 5 жыл бұрын

onlylikenerd because they were just a scam. Overpriced spark plugs with no gains over a decent plug.

@lawnmowerdude 5 жыл бұрын

ACPHOTO so they’re equivalent to a decent plug? That doesn’t sound bad.

@lemmy8947 4 жыл бұрын

@@lawnmowerdude Yea at 3x the price

@anthonycoffey816 4 жыл бұрын

Autolite champions all day every day 😝 at least on older style hot rods

@JayLang7 5 жыл бұрын

Great video

@tylermyers4572 2 жыл бұрын

Just now notice they miss calculated on their engine with a 900 cfm carb when actually they only turned it to 6500 rpm so 383x 6500 divided by 3456 equals a 750 cfm carb seems to be more suited for this engine

@242bleek 3 жыл бұрын

That 383 bottom end with that compression would like a set of 195's better. 220's really shine on 400 plus ci.

@TejasToolMan 5 жыл бұрын

Old school trick running 3 carb spacers on a small blk 318, mild cam & heads with cast iron carter intake makes easy solid hp

@lewisdeclouette6342 5 жыл бұрын

Love the video deuces

@jajupa78 4 жыл бұрын

Ya 536 that's definitely chuckle numbers. After that it got serious tho.) Great build guys.

@josecarreno1709 4 жыл бұрын

How much was the stage 2 build was in total?

@mdbadalmiah6808 5 жыл бұрын

Thank you sir 🇧🇩 🤝

@shaneshane1379 2 жыл бұрын

That would make a sweet street strip Moto. Even drive it to the track

@caratrimble8297 2 жыл бұрын

Does blocking the exhaust crossover help or hurt performance on a street-strip engine?

@jamessheets9205 5 жыл бұрын

If you have a stage 2 build with stage 3 heads and stage 1 intake manifold do you multiply or divide it by a 3/4 race cam? I'm just trying to figure out the mathematical formula.

@timmartin4798 5 жыл бұрын

What is a 3/4 cam?

@BigUnk85 5 жыл бұрын

@@timmartin4798 very old school race cam

@Sam-m04 5 жыл бұрын

john preston heyyyyyy he doesn’t know it’s ok lol

@indyrock8148 5 жыл бұрын

Lol the mathematical formula is $ * number of sponsors parts = $$$$$

@jonathanthomsen7218 5 жыл бұрын

Lol at this rate I think they where missing the other 1/4 of the cam 😂 I havent heard that 3/4 cam reference in a minute that's awesome

@TheWrenchist 5 жыл бұрын

Did anyone catch that they didn’t discuss the accuracy of the digital version. It was last and it seemed they were going from best to worst

@TheGamersRace 3 жыл бұрын

Yeah I was like "haha so don't buy a digital one, got it"

@BustedWalletGarage 5 жыл бұрын

Joe seems like the kind of guy that never leaves a dyno room not covered in oil and broken rods.

@lte008 3 жыл бұрын

At 887 cfm you should have ran an 850. BUT, You are off your target of 8000 rpm by 1500. 383*6500/3456= 720 cfm, or a 750

@Njabuloseh 4 жыл бұрын

Any reason why you didn't show the power figure at 14:48 after switching to the 3inch exhaust? You've showing power & torque the entire video...

@SomethingFunny454 5 жыл бұрын

Bawg Deep!!

@1calvin 5 жыл бұрын

It would be nice to see more Ford or Mopar builds

@skylinefever 5 жыл бұрын

I agree. Practically every car channel has had an SBC build from mild to wild. Although BBC builds are less common, they still are much more common than anything else, and still vary from mild to wild.

@nathanielbolden5053 4 жыл бұрын

Dammitman!...BOWTIES RULE!!!

@jaimecervantes3896 5 жыл бұрын

I wish you were my neighbors” 😏👍🏼✌️🌎💯

@daleyoung601 2 жыл бұрын

What is the static compression of the engine and which AFR 220s the Race ready or the Competition cnc ported heads, with that much cam I would have expected 600+ hp and 550+ torque?

@tdrewman 4 жыл бұрын

I always wanted to see if my torque wrench was in spec. I remember watching a youtube were the person tested a Snap-on, Mac and Harbor Freight torque wrenches on one of these. All of them were in specs. including the 9.99 on sale Harbor Freight ..

@bryanelmechanico7970 4 жыл бұрын

What’s an ideal manual transmission to use with this engine build as well as drive shaft and differential

@jaredmayer3960 4 жыл бұрын

Bryan El mechanico M-22 12 bolt

@mariusfrost640 3 жыл бұрын

I'd like something in between stage 1 and 2, 400-425 HP and 450 lb-ft, any suggestions? Also, it's 14,000 lbs of FORCE, pressure is a different metric.

@lonelypinebeefarm4297 Жыл бұрын

@powernation can you post all the parts used in this build. Getting ready to build my son a 383 for his 62 impala and were looking for 450 to 500hp and this video let's me know it will be very easy to do on pump gas. Also the 93 pump gas you used . Did it contain 10%ethanol or non ethanol

@cardad49646 5 жыл бұрын

Where do I get a plug socket like that? I really could use one

@littlerhino2006 5 жыл бұрын

I think they us a lot of Matco stuff. They have an online catalog, no dealing with a rep and tool truck.

@ryanlee6881 2 жыл бұрын

i’m planning to build a 350 exactly like this and i’m gonna put it in my mini truck

@joshuaherpolsheimer4699 4 жыл бұрын

How do you get the 3456 number from?

@socleanmx6 5 жыл бұрын

What was the cam???

@jamesfowler5789 4 жыл бұрын

Pat what made you choose the AFR 220 head verses the 210 head, or even the 195 head? Could you have gotten more torque with either of the smaller port heads? Thanks.

@shorelinearmorllc477 4 жыл бұрын

If your building your motor and dont want to spend money to upgrade carb later when upgrading motor can your go with a bigger carb but lower the jet size?

@davidreed6070 3 жыл бұрын

What are the specifications of the camshaft

@duramax78 3 жыл бұрын

At the end that summit block how much hp would that be good for.

@oceanhome2023 2 жыл бұрын

I used the formula for carburetor and my 600 CBM Edelbrock was really close !! But I want to make it so I can put on a 750 !

@johndcramblit3045 3 жыл бұрын

I'm curious why you chose the a common crank with a 3.75 inch stroke instead of a crank with either a 3.875 or a 4.00 stroke? Do those 2 require a lot more machine work or something?

@jord9308 4 жыл бұрын

Anti- seize on the plugs will decrease heat transfer from the plug to the head causing shorter plug life. GM has a TSB about this. I know everybody does it, but I’m just sayin’

@kurtpoblenz2741 5 жыл бұрын

Interesting how chevys use a mopar type shaft mount rocker system when building high horsepower motors. Chrysler knew what they were doing 👍🏻

@kurtpoblenz2741 5 жыл бұрын

john preston ..... & you have cooties! 😂😂😂

@kurtpoblenz2741 5 жыл бұрын

Ada 1812 ..... & rent a dumpster when your building a Chevy, so you have a place to put all the garage factory parts 🖕🏻😬

@skylinefever 5 жыл бұрын

The reason Chevy engines didn't have shaft rockers is because they were cheaper, and when an engine has a mild cam, the added strength of shaft rockers is not needed. It only becomes important when aggressive cams are used. As I remember, the Magnum series 318 and 360 was given stud mounted rockers because they were cheaper and didn't have to deal with aggressive cams.

@kurtpoblenz2741 5 жыл бұрын

Skyline Fever .... you are exactly right. 👍🏻

@robking9857 Жыл бұрын

If you buy rockers, 5/16 studs, and then add a girdle, you spend about the same as the Sportsman shaft set-up. It was a choice, not a requirement.

@RidgeRunner5150 5 жыл бұрын

okay where can I get that block for $400? Gimme a part # or link.

@sparkplug1018 4 жыл бұрын

$740 these days, I think this episode was filmed a few years ago. www.summitracing.com/parts/sum-150100-60/overview/ Or you can do what I did and get extremely lucky and find a 4 bolt main 383 in the junkyard for $300.

@Alchemist37 5 жыл бұрын

Pat loves his pens. More pens = more HP :)

@Alchemist37 4 жыл бұрын

@Pop's Garage Mayhem hah yes exactly mate 😁

@cerv707 5 жыл бұрын

7:41 what’s the name of that wrench? I need that!

@tjlovesrachel 3 жыл бұрын

I bet matco makes it

@michaelphelps5064 4 жыл бұрын

I wonder how long the solid roller would live on the street? Is it durable enough to stand the abuse of Pigeon Forge traffic in April? IDK but it would be bad ass at the cruise ins and car shows.

@jarrettnarro1282 2 жыл бұрын

I wonder what this set up would make on E85

@veenoable 4 жыл бұрын

Is it ok to use head gasket copper grease before installing any head gasket?

@ekscalybur 3 жыл бұрын

Yes. Just be sure to taste test it first, you absolutely don't want to use rotten grease.

@TheGamersRace 3 жыл бұрын

I like how they gave the accuracy of the bar type and click torque wrenches, and then just casually skipped on the electric one haha.

@jeepin4on4 3 жыл бұрын

Love this channel, but I use the click torque wrench. LOL skid-more to calibrate. The team is always welcome at my shope....

@AfflictionSuzukiGsxrLosAngeles 3 жыл бұрын

I couldn’t find the gm 5.3L block on summit’s website. Anyone know how to search for it?

@gmfan6029 5 жыл бұрын

I wish they could tune my 350

@desousa302 5 жыл бұрын

Whats the total cost of this stag 2 build.

@reidmackay9703 5 жыл бұрын

What if u have a 383 and turn it 8k but u have boost the CFM won’t be the same right?

@poncoolride 5 жыл бұрын

You will need a LOT more cfm

@Kramer178racing 4 жыл бұрын

What rpm you check timing at? 😊

@brents4729 3 жыл бұрын

Im pretty sure the advance was locked out on that distributor. The timing was set at what seemed like idle so it would have to be.

@richardmartin6533 5 жыл бұрын

I'm missing some information here. when you use a 383 crank, what starter motor do you use? does a 350 starter work on a 400 crank?

@travisbryan3131 5 жыл бұрын

Any small block starter will work on pretty much any small block. Same with a big block

@skylinefever 5 жыл бұрын

You can by the same pattern of flywheel/flexplate teeth for the 350 and 400 crank. The only difference is that a stock 400 crank is externally balanced and needs a flexplate/flywheel that has a weight on it for external balance. I think some aftermarket 383 rotating assemblies support internal balance so that the special flexplate/flywheel and special crankshaft pulley are not needed.

@kingdavid1975 5 жыл бұрын

Lol

@bilbobaggins4710 5 жыл бұрын

@@kingdavid1975 hahahaha 😊

@diane2193 5 жыл бұрын

The 383 is a 350 cu in with a 400 crank. Wonder what a .030 over would be

@r3ddr8gn80 4 жыл бұрын

I'm not that familiar with engines but could you use that engine for a daily driven vehicle, and will it hurt you at the gas pump?

@canabox7112 5 жыл бұрын

I bet if you repace that intake with a RPM air gap you'd gain 60ftlb and only lose 15hp

@MRHSDM316SD18186 5 жыл бұрын

You guys did a video where you used the GM LS engine & gave a "suggestion list" on what parts on teh fuel injected LS would have to get removed & replaced with an intake for a carb & suggested a carb to feed the LS; I cannot find that video for the life of me. I want to cross post it to a FB group that I belong to that's dedicated to "Square Chevy" trucks.

@skylinefever 5 жыл бұрын

MSD invented a computer and fuel system that makes LS swaps plug and play and not require any OEM wire harness. You could wire an inline fuel pump without too much trouble. That would be better than a carb.

@the4flatgarage 3 жыл бұрын

How do you get connecting rod caps off high dollar cap screw rods? You ain't gonna hammer on a nice set of 6 inch "H" beams.

@leerjet31 4 жыл бұрын

I would use valuecraft 99¢ plugs before I used E3 LMFAO 😂

@kylewest100 5 жыл бұрын

Question on the LS summit block. Do iron blocks have the strong long lasting piston sleeves like the aluminum blocks? Never messed with a iron block so idk.

@brian_sipe 5 жыл бұрын

Iron blocks don't typically use sleeves. It's all one piece.

@alexcorona 5 жыл бұрын

There are some that use sleeves but most don't. You can however install sleeves on any block. Darton sells them for SBC and pretty much any popular engine. They also do custom if you need them.

@kylewest100 5 жыл бұрын

ACPHOTO reason I was asking my 6.0 had 230k when I decided to rebuild it. The piston walls still had the hatch marks from the factory and the bottom end was still within spec so I just resealed everything and had the top end rebuilt and put new cam bearings in because it was a DOD engine and the original cam ate up one of the cam bearings. So long story short I was impressed by how durable the bottom end is on the LS engines.

@brian_sipe 5 жыл бұрын

@@kylewest100 the gen 3 and newer blocks are hardened at the cylinder walls to reduce wear. Makes it harder to bore them over as well.

@skylinefever 5 жыл бұрын

Most iron block gasoline engines don't use sleeves. Sometimes, when a block is damaged or has reached its maximum overbore, sleeves can be fitted. Some agricultural use gasoline engines do have sleeves. Large diesels are a different story. Most of them use liners.

@johnmcwade222 5 жыл бұрын

When is the show coming back to tv?

@wolley2012 5 жыл бұрын

History channel now

@JimTheZombieHunter 5 жыл бұрын

@19:42 - No parasitic loss? How do you figure that?? If it's doing work (pumping coolant), then it requires energy to do so - in this case (assuming a street driven car) from the alternator. Difficult without some very expensive kit and a gaggle of white coats to determine if the electrical resistance (dissipated as heat) offers any real advantage over the frictional losses of driving one less pulley - but to suggest an electric pump offers a null? Physics simply doesn't work that way. As well, although a slightly different concern. I'm assuming the pump uses a brushed DC motor? The commutator and brushes naturally being wear items with a finite lifespan by default, and in continuous operation no less. I have a hard time believing that this setup will come anywhere close to approaching the service life of a low tech belt driven pump. Of course this from the perspective of a commuter ride - perhaps longevity not a concern on a build like this, but still .. aside from the gee-whiz aspect, I just can't see the point in embracing electric.

@otm646 5 жыл бұрын

You're dead on. Going electric offers a few advantages which the aftermarket has not yet been able to seize upon. The biggest aspect is a variable flow water pump decoupled from engine RPM. Even then you're looking at a horsepower or two for all that cost and complexity.

@skylinefever 5 жыл бұрын

I have heard that some BMW engines have electric water pumps only, so I guess it saves power to have them. However, I am not sure how relaible they are, as BMW likes to put fragile plastic parts in their cooling system. One solution I have seen is having an engine with the standard belt driven pump, but instead of having the belt connected to the crank pulley, they have a belt connected to an electric motor. That sounds like a better solution, especially with classic cars and engines that weren't built for electric pumps. Here is an example from Moroso: www.moroso.com/electric-water-pump-drive-kit63750/

@tomrose6292 3 жыл бұрын

Interesting.

@tomrose6292 3 жыл бұрын

Heck if they are going that route .there was a belt driven distributor for sbc .I saw one in a Herbert performance magazine.back in the day..a friend of mine said he was going to get one because he wasn't tall enough to reach the back motor where it's at..so ford had sympathy for short guys and they put their dist in the front.lol

@timpeters4699 2 жыл бұрын

I love it when he said or simply get on summits website and put the thing on he was looking at him like what the f*** are you talking about. Surprised you didn't put all the markers in his pockets. I have work with guys like that and let me tell you most guys will be like what in the hell get that guy out of my shop know-it-all.

@adilnadaf9182 5 жыл бұрын

Hi.. that LS block u talked about. Can it be shipped to other countries?

@bilbobaggins4710 5 жыл бұрын

Email Summit Racing ...Google it

@alexcorona 5 жыл бұрын

Summit Racing will ship International.

@ekscalybur 3 жыл бұрын

I'm afraid not, sorry. All Chevy's that get shipped overseas are required by law to leave US soil with Puegot engines. National security and all that.

@adilnadaf9182 3 жыл бұрын

@@ekscalybur I mean.. just the block

@ToxicMisfitsYt 5 жыл бұрын

Pay 600$ for a intake has to drill holes in it

@stevewall6811 3 жыл бұрын

“No cutting corners on spark plugs either” *Proceeds to use E3 plugs*

@damonkatos4271 4 жыл бұрын

While watching this, I saw an ad for Maxim automotive integrated circuits. Buy Texas Instruments automotive integrated circuits!!!

@mbm460ns9 4 жыл бұрын

is joe still on one of the shows?

@michaelovitch 5 жыл бұрын

Electric water pumps use electricity. Electricity is produced by the alternator,wich create a load on the engine. The interesting thing would be to measure how much load it creates because of the pump and see if there is really a benefit,of an electric pump ,in cars.

@brian_sipe 5 жыл бұрын

an alternator has a constant load, the load doesn't change because you used an electric pump. That's like thinking your engine will have more load on it when you turn on your radio.

@numinous4789 5 жыл бұрын

There's no comparison - the parasitic losses of a mechanical water pump far exceed anything indirectly related to an electric pump via increased electrical load. And increased electrical load on the charging system does no create increased force necessary to turn the alternator. You're chasing ghosts.

@michaelovitch 5 жыл бұрын

@@brian_sipe The loads differs following the amps used. You can easily loose 200 rpm of idle if you switch on,headlights,blower fan,and defroster on a carburetted car. You don't see load varying because the idle air valve compensate for the load on fuel injection. Load is not constant at all.

@brian_sipe 5 жыл бұрын

@@michaelovitch load is the amount of engine power required to spin the alternator. That load doesn't change. I'm not talking about the amount of electricity that is used. Also your car's rpm will not change if you turn on the headlights. It will change if you turn on the defroster, since the defroster uses the air conditioning compressor to operate, and that increases the drag on the engine's accessory drive.

@numbnutz9398 5 жыл бұрын

The alternator does not have a constant load. An alternator turning when the engine is at say two thousand rpm with no load on It will take little power to turn. Put on everything in your car head lights, rear window defoger , two hundred amp stereo, cigarettes lighter, etc and that alternator will be much much harder to turn. The benefit of the electric pump is it still takes less power than a mechanical set up. When I was a kid at the local science museum they had a bike set with a generator and a row of light bulbs. As they switched each one on in sequence it got harder and harder to the point that you just could pedal anymore. Same principle. No free rides when energy is concerned.

@AfflictionSuzukiGsxrLosAngeles 3 жыл бұрын

Anyone knows the partner for that 5.3 LS engine on summit’s website