Today we teach you how to properly prime and glue pvc or cpvc piping. Amazon Affiliate Links: CPVC Glue and Primer Kit: amzn.to/3Uopqbe PVC Glue and Primer Kit: amzn.to/3o1QYYc Yellow Low-Temp CPVC Glue: amzn.to/3ZTLdsJ
Пікірлер: 23
@Missionary1173 ай бұрын
Your tutorials are great. To the point, clear, and concise. Please keep it up!
@HandymanHertz3 ай бұрын
Thanks, I appreciate that!
@Troy-McClure8127 күн бұрын
For higher pressure or irrigation I always recommend Emery cloth the pipe before prime and weld,it takes off the clear seal and helps with the reaction.I use all purpose clear cement.
@HandymanHertz26 күн бұрын
Interesting, that's for the input!
@belindahugheslifestyleАй бұрын
Thanks. These two videos suited my project and my knowledge level perfectly. Keep 'em coming.
@HandymanHertzАй бұрын
Great to hear it helped! Thanks for watching!
@belindahugheslifestyleАй бұрын
@@HandymanHertz I followed your instructions - and it all worked! I would add: maybe put the cleaner and cement jars in a low profile plastic box to protect your tools, etc in the event of a spill by wind or human. Thanks again. High five.
@HandymanHertzАй бұрын
@belindahugheslifestyle good tip, they can get messy!
@theadorephaedon16913 ай бұрын
Great video! Thanks 🙏
@HandymanHertz3 ай бұрын
Thanks for watching! 👍🏼
@jmy7799Ай бұрын
Do you have a video on capping? (how to select the right type and how to install) Confused by pressurized vs non, as well as whether water valves need only be shut off locally or at a main source. My initial thought was that as a drain pipe, the water wasn't a concern, but I have seen some confusing advice online. I am needing to trim down an unused sink drain pipe that sticks out from the wall about 12 inches in our laundry room. (We want to place our deep freezer there instead of using it for a sink--but want to preserve enough on the drain pipe in case we need it at some point in the future.) I am a single mom and would like to do this myself since it seems like it should be simple.
@HandymanHertzАй бұрын
I do not have a video on capping, but I may be able to help you. If your sure it was to a drain, it will not be pressurized. Cut the pvc correctly (I have a 2 minute video on that) and glue it correctly, as shown in this video. You can take the cut piece to the store for a fitting or measure it for the cap. Very simple. You can do it 👍🏼
@Fragmentofbone2 ай бұрын
Do I need special glue for PVCU?
@HandymanHertz2 ай бұрын
i'm not familiar with PVCU. maybe you meant PVC? You can use CPVC glue for PVC but you cannot use PVC glue for CPVC. I believe the reason being, pvc is for drains and the glue is not designed to withstand as high of heat like the chemistry in CPVC glue, which, CPVC is for pressurized lines. It would hold up and be leak proof, but would not probably be code in your area to use PVC glue on Cpvc pipe, and would cause issues if theres a fire/ excess heat.
@Fragmentofbone2 ай бұрын
@HandymanHertz No. Its Polyvinyl chloride un-plasticised PVC-U and I was wandering do I really need the specific glue for it, or I can just use regular PVC glue?
@HandymanHertz2 ай бұрын
I do not have any experience with that so I cannot help you out. Sorry!!
@Fragmentofbone2 ай бұрын
After a mind numing adventure with chemical data sheets. I can finally say that (probably) PVC, UPVC and PVCU are all thesame thing. I think the confusion comes from that in Chechia they call PVC a PVC-U. I will use regular cement. I guess if things fall apart, I will know the next time.
@HandymanHertz2 ай бұрын
@Fragmentofbone thanks for the update! I'd be curious to be updated on your results
@Krumholt4 ай бұрын
I used pvc glue with purple primer on cpvc
@HandymanHertz4 ай бұрын
From my understanding, that will still work, but it’s not code because it has less heat tolerance than cpvc glue.
@Krumholt4 ай бұрын
Yeah 40-110 degrees. Sheet rock was put up, floated and painted. lol lesson learned, redid them. such a hard kick in the crotch @@HandymanHertz
@gial88622 ай бұрын
@@HandymanHertzwhat does chaffered do?
@HandymanHertz2 ай бұрын
Champfer helps by taking out any lip that would remove the glue from the fitting. as the pipes slides in, if there is a burr around. That's for the outside, the inside reduced the chance of water turbulence.