Young bloke does a good job demonstrating the issues. Thanks mate.

That was one of the most informative and easy to follow carby assemblies that I have seen. Thanks mate.

Had a Victa that had been sitting around for years that didn't want to start. Thanks to your video, I was able to diagnose which of the carb parts needed replacing and with your 5 Piece Carb Kit, the carb is now serviced and she kicked over first time. Cheers.

Thank you for these videos guys! Its helped me fix my old victa 2-stroke, and given it another 10 years life!

Very informative guide to Victa carbies. Your step by step instructions are easy to follow and the excellent camera work adds confirmation and clarity to the clip. As with all of your videos, very well done guys.

Great video, this helped me so much!!!! Thankyou

Thanks for these videos. Pulled the carby apart and cleaned everything. It was absolutely gummed up. Mower working again, better then it has in years. Not bad for 25+ plus Victa. I was on the verge of buying a new mower.

Great video! this is the only vid that I have found where you talk about the A B C in the carby. I have been looking for move revs this helped cheers

You just repaired my edger. Thanks very much!

Thanks for the video. Very helpful and it helped me immensely to sort out my Victa. Much appreciated.

good demo mate saved me a lot of time.

Brilliant did this today saved my vista xxxx

Good description but there is an annoying clicking sound in the background. The poppet valve as you described has the 3 positions and in order to get a proper idle I have also installed a brass shim washer to get a good idle with no issues on high revs.

Very helpful and well presented, good job.

as always, pro work with pro video demonstration...cool

Thankyou for the video, bought my parts from the site and installed.

Very informative thank you for sharing.

Very helpful. You do great stuff.

absolutely nails it!! thanks so much!..

Brilliant instructions...thanks mate

Excelent demo. thanks

Great video man 👍

Great video and was well explained and you covered a lot of items that i.e (A B C) have been missed so I have ordered a full carby kit from you to fix the next door neighbours Victa after his son worked on it and now wont go after losing the needle in the lawn and then stuffing up his other identical Victa which now wont go.. Thanks a lot.. well done

a well done video. thank you.

Thanks for this video, i have been given 2 of these mowers, i don't really need them as i have a dozen or so assorted mowers that i have got going, but i like doing them, however, i have not had this type of Victor of this type before. one of them is a big one with a large separate tank, looking forward to doing this up.thanks again.

I turned the poppet 'A' next to square notch, is ok but seems to now be an extremely sensitive throttle, tiny movements produce dramatic engine speed changes, you can slow it down to a very slow idle still, but because of the sensitivity, hard to get the precise engine speed you want relative to the work load..it also seems a little heavy on petrol...I know all Victa 2-strokes are by nature heavier on juice than a Briggs 4-stroke but seems thirsty even for Victa 160cc. Meanwhile, I have solved the original issue which was cut-out from apparent kill-switch short-out at all but max throttle when warmed up. Have kill-switch unction at the appropriate throttle position only now.

The ball was not clicking in so I made a hook with mig wire and helped it a little

I followed the guide to lining up the poppet valve but some poppet valves are different They only have an A & C. And its the "C" that needs to be lined up with the jet hole otherwise the engine will over rev!

Putting the throttle in the run position lets more cable out making it easier get a hold of.

Clarity wasn't the best with the needle. Which end do I put in the hole and why?

Hello, my uncles victa 160 has starting issues and when it does start, it revs like crazy and runs the fuel tank out fast. We have checked the carb o rings, even got varietech metal float needle, air filters, snorkel, fuel lines...which all seems fine. The decompressor was blocked off years ago and was running ok. Can you suggest any ideas? Thanks

I need spare parts

I got 2 stroke victa mower , its starting alright but engine running not fast enough.done replace diaphragm , jet nuzzle and orings!!! any idea please ?

No matter what I do I cannot get the cap at 5:30 in your video to seat firmly. I can't detect any damage on any of the parts, it just won't seat like it should. Notice also that the breather (?) hose wasn't connected to the engine, does that make a big difference in the running of a powertorque engine?

G'day How do I tell the G4 from the new LM carby?

popped valve has no A B or C so what can I do?

Great Video. I purchased an 8 parts repair kit for my G4 carburettor and installed as per the video. My mower will not start with the normal priming and accelerator in the start position. To start I place the accelerator in the full on position. To maintain the revs I have got to move the accelerator up and down continually. Please advise on this problem.

aA

Bloody annoying background noises.

What’s with this bloody Yankee carburattor business, It’s pronounced carburettor, Otherwise an excellent instruction thank you