"It was an atx case?" "Always has been" *Gunshot*

love the way the gpu looks!

Looks good, but glass panel psu will choke, no air moving over vrm or m.2 where are the tempe😊

meshroom is such a nice case, i wish the mesh panels were more rigid though

One of the best parts of windows 11, is that if your CPU has an integrated GPU, you can just put your monitor cables into the motherboard, and do not bother with putting GPU ports. System will utilise discrete GPU accordingly, depending on load. Which means, you can make insane builds/chassis.

Very nice build. Just finished mine but I put the GPU in the front and the PCU in the back. no cables exposed!

nice build

Oh that is so awesome! i have been searching for a sff atx case, great vid :)

I wonder how the PSU will get air to cool?

你的Riser Cable是多长？

Thank you for posting this video 🎥🍿🍺🇺🇸. You have a new subscriber 🎉. Keep up the great 👍 work 🎉. An amazing 🤩 build.

how was the thermals? 4-6 hrs usage?

Can anyone please tell me more about the gpu riser cable he used? I have asrock B450 motherboard and amd 5700xt, what cable should i use and how long that should that be for SSUPD.

Tell me is 15liter for matx case , consider a small or just decent?? Im talking acer u300 case Do you have any case recommendations that support matx mobo and atx psu Smaller dan acer u300??

what tools do you use?

maybe flip the power supply, it can't get airflow and the VRMs on motherboard are also in still air. Beautiful build, but everything on the left side is going to heat soak, maybe if the power supply is flipped it can pull atleast promote a little airflow from the m.2 heatsinks, VRMs, and also cool itself in the process a little.

I wonder how PSU fan get air flow if this case does not have mesh panel instead of glass one ? will the AIO radiator het hot because of hot air from GPU ?

psu say please let me breathe 😂

Am I crazy or the MB did stuck out then somehow it didn't, and magically fit into the case later on ? 3:35 - 3:43

Can Install the radiator 360mm ??

Psu dead by that glass if used too long. I might buy this case and make diy/3d print attachment for eatx case.

The PSU is choked though. A mesh panel would've been better. Not as pretty but definitely more functional.

I would certainly change the orientation of the AIO fans to pull fresh air from outside and avoid the hot-air recirculation from GPU. Better if it is facing the mesh first prior the rad. Also, since there is no other placement options, I would definitely use mesh side panel over TG. Less visual appeal but more practical in cooling. Flipping it to face the inside of the case if TG use is preferred, to get air from inside the case. Not very efficient, but it'll way more effective than facing dead-on a glass panel.

I feel bad for that power suuply

The graphics card will vent its heat to the sides that the AIO fans next to it will suck the hot air into the radiator. Not the ideal combo for performance but this is just for aesthetics.

Ncase M2 matx build

featuring the psu with a clear panel but not the gpu is a mistake

Why it's so loud at the end🤔 and that squeak

И зачем там стекло, с таким то видом. Кабеля как лапша в коробке, да и блок питания в глухую стеклянную стенку. Не практично, да и не понятно как себя поведёт водянка 240 в таком пространстве. 😢

Nice case..weak mesh

]he will never run stress test on it.... it will literally burn

There's no room for cool air inside this case

че то выглядит так себе, собирается сложно, зачем такое надо