Put lemon On Your Electrical Soldering Iron And Admire Results

Рет қаралды 239,712

3 ай бұрын

Clever! Put Lemon on your electrical soldering iron and admire the results
This video shows how to repair electric soldering iron using only salt. Put salt on your electric soldering iron and you will be amazed by the results. This is the best way to use electric soldering iron.
electric soldering, how to solder, repair with solder, how to repair soldering iron, how to clean soldering iron,
Inventor 101 #howto #soldering

Пікірлер: 62

@robertgutheridge9672 3 ай бұрын

I just use a piece of sandpaper in lightly sand to tip my soldering iron to get the oxidation off and then dip it in soldering flux saved a lot of time compared to doing 12 volt electrolytes

@richphoenixpa 3 ай бұрын

I suggest using a copper brillo pad.

@TekWar98 3 ай бұрын

Most tips have a copper core with iron, nickel and chrome plating. Sanding or using a file will destroy your tips.

@TekWar98 3 ай бұрын

@@richphoenixpa"copper" Brillo brand pads are copper plated steel wool. Get a brass cleaner or a sponge designed for soldering.

@richphoenixpa 3 ай бұрын

@@TekWar98 I couldn't remember if was copper or brass... but the point is that it's usually what we use.

@robertgutheridge9672 2 ай бұрын

@@TekWar98 soldering iron tips are consumables. And sand lightly just enough to clean the crud off. although I have a couple that I have taken a file to a reshaped them down to very thin points because I needed to tips are relatively cheap.

@ElectronicDesigner 3 ай бұрын

Hello, I wish you continued success. ☺️

@JohnWinquist 3 ай бұрын

New tips are only a couple $'s at the most. Soldering iron tips have a coating on them, once it's removed they are worthless. Don't do this or use sand paper on them. If you want to keep your tip in good condition, dip it in flux before you solder. And then after you're done, dip it again and melt solder on it before it cools. My tips last well over 5 years, with regular use, doing that.

@fL0p 3 ай бұрын

And even then, tip refresher costs you a couple bucks and works like a charm, it cleans in a non destructive manner

@JohnWinquist 3 ай бұрын

@@fL0p That's cool, I didn't even know there was such a thing.

@JohnHall-uv2jm 3 ай бұрын

Yeah I said sand paper first. Or coca cola

@SillyGrampa51 2 ай бұрын

@@fL0p keep your iron clean with sal amoniac like they show you in metal shop high school

@alvydasjokubauskas2587 3 ай бұрын

So you did 12volt electrolysis?

@fffUUUUUU 3 ай бұрын

Yep, and he didn't even tell which + or - wire to connect to soldering tip 👎🤦‍♂️

@gerncranium4550 3 ай бұрын

@@fffUUUUUU If you look carefully, he attaches the wire with the white stripe to the soldering tip, which is usually the positive.

@fL0p 3 ай бұрын

@@fffUUUUUUimages.app.goo.gl/7yvDcZgeRiEz3KFYA YW

@diyfireking 2 ай бұрын

Great video 😍😍

@tenncutt 3 ай бұрын

How about just clean the tip with a file or emery cloth. Works perfect

@briansalisbury4764 3 ай бұрын

Sandpaper or a wire brush works just as good. But there is paste that is specifically made to tin your tip or regular soldering paste or Flux works just as effectively. You should have soldering paste around always anyway. It ensures a good solder flow and connection. This process here is unnecessary work, which accomplishes the same thing.

@NguyenDIY9 2 ай бұрын

Nice, i love

@StuffJason437 3 ай бұрын

Great prison content !.

@AmazingSmart-ngth 3 ай бұрын

This is really informative and useful. Thank you for this amazing video.

@myoaung4504 2 ай бұрын

So thanks sir. ...!!!

@tdkreatif 3 ай бұрын

Nice tricks

@temjaiwannasa4816 3 ай бұрын

Nice ❤❤👍👍👍

@mikejones-vd3fg 3 ай бұрын

cool, i thought you were going to whipe it with lemon juice

@abdykalyev_top7878 3 ай бұрын

Nomber 1

@Nebby_99 3 ай бұрын

It didn't even improve the performance of the tip 😩 There are plenty of videos out there showing how to clean a soldering iron tip properly.

@DavidSanchez-qq1xr 3 ай бұрын

I use a brass wire brush when the iron is hot, it takes about 15 seconds

@user-yu3fo9cq5f 3 ай бұрын

Nice 👍

@davidwilson4190 3 ай бұрын

My wife said to clean the tip before use but the wire brush is a little rough on my tip, lol

@user-sandia 3 ай бұрын

De que tipo de metal es el tornillo

@bigbadassredhead69 3 ай бұрын

You could have got the same results in about 2 minutes with a wire wheel

@Susie_Floozie 2 ай бұрын

The short-sighted philistines who always sneer "Just go buy another one" at your experiments just don't get it. If they could think outside the butt, they'd understand that you're using a visual format to demonstrate basic, solid principles that are damned useful. I've been adapting your various techniques for my own bimbo-rigged projects, and they give me a real edge--like, this knowledge has possibilities. I go digging around for old artifacts, and if I ever need to clean up some badly corroded metal geegaw, this method might be just what I need. Thanks!

@jaguarcap6494 Ай бұрын

Are you idf bot? Why do you use philistine as an insult?

@blackpink_1023 3 ай бұрын

Can you make stand dc motor fan please😊😊😊😊😊

@user-do2gh5vi3b 3 ай бұрын

It's freaky hey

@agarge 3 ай бұрын

Sand paper...

@AzizAziz-yu5ov 3 ай бұрын

👍😀

@Thelastone384 3 ай бұрын

So... basically you produce a very diluted bleach (sodium hypochloride) for cleaning the soldering rod? I supose that this sodium hypochloride reacts with any metal that is covering the surface of the rod?

@anjanasrivastava4576 3 ай бұрын

why water has turned green....which compound is it

@MoviesByeMark 3 ай бұрын

Copper sulfate?

@tenncutt 3 ай бұрын

Yes copper@@MoviesByeMark

@PlayEasyG 3 ай бұрын

😂😂 bro you damage minimum 50 -70 rupees charger, wasted more than 2 hours of your life to clean a bit, simply use a normal file to rub the tip and user iron without issue that or why didn't buy a 20 rupees iron bit . That problem happen after every 2-3 days of use iron if you are a regular user so every time do this again and again bravo 👏👏👏

@fffUUUUUU 3 ай бұрын

he didn't even tell which + or - wire to connect to soldering tip 👎🤦‍♂️

@Fahimkhanwtc5980 3 ай бұрын

টিভি টিক করা সোল্ডারিং আয়রন ভালো

@sidinator3000 3 ай бұрын

Please nobody try this

@seetheworldfrommyharley 3 ай бұрын

Skeerd! It's too dangerous 😜🤣

@bettyir4302 3 ай бұрын

Easier and quicker to wipe it off on a wet paper towel after every use.

@MrHeHim 3 ай бұрын

It's annoying and they know what there doing. This channel only do these videos for engagement

@richphoenixpa 3 ай бұрын

oye, one thing I notice is they don't use any flux. flux is acidic and used to clean the surfaces of oxidation and allow the solder to 'wet' the contract surface (regardless if it's the thing you're trying to solder or the iron itself). as for the electrolysis, if it was being used to 'resurface' an iron, I could see it, but it's usually a lot better (for temperature control) to just replace the head since it's important to have an exact thickness of the iron head to have accurate temp control.

@Alpeshgaming710 3 ай бұрын

Hellow i am first comment ❤

@OmarShixaliyev 3 ай бұрын

Zu idakani yayama vu

@fL0p 3 ай бұрын

Hello I Am Underwater 🫠

@Abdulmomon22-jh9pu 3 ай бұрын

সবাই ভালো আছো🥰

@bobsiburton861 3 ай бұрын

This video should be banned. This is extremely dangerous

@GaddarKerimEU 3 ай бұрын

Just use a sandpaper or if you have hobby Dremel use a polishing discs. Why do you so complicated 🤔

@TekWar98 3 ай бұрын

No, no and NO! See above reply!

@JohnHall-uv2jm 3 ай бұрын

This guy is as lazy as they come. A piece of sand paper will be faster than standing around waiting for it soak. But if you're lil arms can't do that little bit of work. This would be still faster than his way. Soak it in coca- cola