How to Program Remote Control duplicator

No video

How to Program Remote Control duplicator

Рет қаралды 1,073,498

Күн бұрын

Newer version, more compatible ： • How to Program Remote ...
www.aliexpress...
Link from DE: www.amazon.de/...
In the configuration and selling process, most clients wish to replace the original remote control with a general remote control, while such remote control has not be developed. You may configure your remote control within 2 seconds if you meet the following three conditions:
Condition I: the original remote control may be used normally
Condition II: frequency of original remote control is 433Mhz
Condition III: IC model of original remote control is 2262 2260 1527 2240 and compatible IC (rolling code remotes will not work)
Application method:
1.Clear the copy remote controller: Long press the above two keys at the same time and release your hand when the light flash quickly.
2.Copy: Press the button of the copyed remote control with one hand, and press the button of the new remote control with the other hand, keep for a few seconds
3.Use:If all the above operation succeed, the romote control can be used dirtectly. If it can not work, please operate again from Clearing
4.Recover: If you meet misoperation and cancle useful codes, before re-copy, you can press the below two keys at the same time for 2 seconds and release when the lights flash quickly, then the control will be recovered

Пікірлер: 151

@RomanVideos1 3 ай бұрын

I did copy the signal but the gate still doesn't open...

@qiachip 3 ай бұрын

I'm glad you asked the question, I hope I can help you First of all, you need to figure out whether the signals you copy are the same, because the signals have different frequencies, such as: 433,315; and the signals also have different formats, including 16-bit and 32-bit; the signals also have different ways of changing: For example, the ordinary 1527 has no change, but there is a rolling code that changes; You need to ensure that these are the same, i.e. you want to confirm; What frequency does your remote control have, what format is it, and is it a rolling code? Is your clone remote capable of replicating this type of remote? By solving the above questions, you will know what products you need to purchase; Now from the analysis of your words, you copied successfully, but you can't open the door. Based on our experience, we judge that your original remote control should have a rolling code, so although it can be copied, it cannot open the door. You need to replace it with one that can be copied. Copy remote control for rolling codes Hope the answer can help you Also looking forward to your follow-up feedback

@RomanVideos1 3 ай бұрын

@@qiachip My remote is 433. i figured out that the gate accepts a different frequency so it doesn't recognize my remote. i've ordered a different one that can copy multiple range of frequencies. but thanks for the help.

@nunosilva513 Жыл бұрын

You really helped. I was not getting my remotes copyed untill I understood that they has to touch each other. Thanks !!!!!!

@vbp6159 Жыл бұрын

Only the text with explanation was alittle fast but the info from this video was very usefull. thank you sir.

@Arneby 4 жыл бұрын

After watching this it's easier to understand why so man parts of the world just don't work. Imagine this guy being in charge of just about anything.

@brettsalter3300 2 жыл бұрын

Agreed, Unclear which buttons are pressed, their thumbs obscure any accurate demonstration.Terrible, and frustrating.

@supinac17 3 жыл бұрын

I found several stupid tutorials but yours is only usefull. Thanks

@victorko5671 Жыл бұрын

Wow, you just saved us time and money! Thank you!

@user-ij3hp1km6g 6 ай бұрын

I don’t know for you guys but for me it works perfectly and with two different types!! Thanks for the informations Sir!! You saved me 60€!!

@2007spiderman2007 7 жыл бұрын

In your example you need to hold A and B until leds flash twice, then while still holding down A pres butt B three times on the third press the leds will flash rapidly you can then let go of button A, This will clear the codes. In your example after you thought that you cleared the codes you can still see the leds on B, C and D light when you press the button !

@qiachip 7 жыл бұрын

The LED flash only indicates that the receiver receives the signal.

@sheikdawood7124 6 жыл бұрын

Hi sir please contact number sent me my no 9884231246

@mariaduran6139 4 жыл бұрын

But the lught is still Blue

@ninomb1137 Жыл бұрын

Thanks this work for mine

@NexaTube Жыл бұрын

That's right.

@slovenec88 7 жыл бұрын

Thank you! It works on a generic one, just remember to put antennas together.

@qiachip 7 жыл бұрын

Oh, thank you so much for your advice.

@dimchegcom 2 жыл бұрын

Thank you, mate! You literally saved me 40€

@hadjikorbi1652 Жыл бұрын

@lebeyes 3 жыл бұрын

This works perfectly with the Hörmann HSM4-868

@genin69 4 жыл бұрын

ok 1:44 so smash them together works!

@qrsimon 4 жыл бұрын

Hulk smash

@paricutin149 Жыл бұрын

Thank You!

@WRAND2208 7 ай бұрын

It works man!

@randolphsnyder1505 Жыл бұрын

I did the cloning of original fob,orig fob has 3 functions open,stop and close ,all on same button.cloned fob only opens,no stop or close.Any ideas ?

@wilberthiebert5075 5 ай бұрын

I had the same problem with the same remote. I have to cloning open in A button and close in B button. If open with A it stop with B and close again with A. It's because it's a rolling code. With other remote I had no problem.

@miftachulhuda6341 5 жыл бұрын

I have remote nd both have same code how i can get another code without cloning another remote?

@user-qg4sn5tn7l Жыл бұрын

315mhz or 433mhz?

@rodi9876543211234567 7 жыл бұрын

thank's, your video is complete!

@offroader22 6 жыл бұрын

When resetting; what's the difference between the way you did it wrong and the way you did it correct?

@qiachip 6 жыл бұрын

Hi Espen Loken, The correct way is to put 2 remote control really close in order to get in range when you are trying to copy a key. The remote control won't be able to copy each other if the distance is too far away. It is better to stick 2 remote controls side by side in order to make a successful code copy.

@offroader22 6 жыл бұрын

@@qiachip yes. But I can't see the difference between the right and the wrong way to clear the code

@taewonhwang3181 6 жыл бұрын

there looks no difference of course

@Omarshoukry2012 5 жыл бұрын

Sorry, but i think i understood the question differently. i though it mentioned while resetting not while cloning. i have the same problem when i try to rest its always appears as its mentioned wrong and never been correct! .. the main concern here is what excatly is the reason behind WRONG and CORRECT and how we can make it CORRECT!?.. i will appreciate ur answer

@user-gx8id1tq6d Жыл бұрын

Is this true for all remote controllers of this size?

@olsitafaj3571 4 жыл бұрын

Thank bro😀

@TJBiker1200 4 жыл бұрын

Thank you!

@ahmadzahidi3552 2 жыл бұрын

thank you it works

@Ioan_C Жыл бұрын

thanks a lot!!!

@hayatinicindentv7133 4 жыл бұрын

Thank you

@letechnochat 4 жыл бұрын

thx for your video

@bluebirdsalive5995 3 жыл бұрын

Thank you very much, perfect video just the core things short and clean, thank you!

@DavidRamirez-be1ke 3 жыл бұрын

Did you have to hit the learn button to program it?

@qiachip 2 жыл бұрын

Hello, there is no need to learn the button, just copy the code of the remote control

@peterh1875 4 жыл бұрын

never get to blinking on my remote

@peterbroad1772 3 жыл бұрын

Same here. Press A and B together and hold and the LED is on and it never blinks or resets. Garbage.

@Z19901000sadd4m 2 ай бұрын

can I add a third remote without effecting any of the other two for a garage opener

@qiachip 2 ай бұрын

I'm glad you asked the question. From your question, I can understand your concerns about duplicating the remote control. I'll answer your question first, and then I'll explain the principle. You can add a third remote control without affecting any of your previous remote controls. The reason is that the duplicat remote control copies the code value of your garage door remote control, and then they can both transmit the same signal, without any interference to the original garage door remote control. After they are copied, they can be used as independent remote controls! However, there is a more complex rolling code remote control that is a little different, because the code value of each signal they transmit will change, which requires specific analysis! I hope to solve your doubts and look forward to your follow-up feedback!

@Vlad_in_the_Dale 3 жыл бұрын

Thanks a lot, helped me with this little monster!

@DavidRamirez-be1ke 3 жыл бұрын

Did you have to hit the learn button to complete the programming?

@Vlad_in_the_Dale 3 жыл бұрын

@@DavidRamirez-be1ke No, not really.

@sarai7512 Жыл бұрын

Everything done exactly like the video but the door didn’t open . Note: when im doing the copy process when I press and hold the old key remote the garage opens I think this wrong. AND Same frequency 433mhz please can you help

@amitvalecha1792 Жыл бұрын

Can it be used as remote for my car central locking

@zeuline1 Жыл бұрын

I did all the same. Reset, clone. Lights the same blink, after clone steady on on press, but remote doing nothing. On old remote the same MHZ 433,92. Where can be trick?

@sarai7512 Жыл бұрын

Same

@hantozoli Жыл бұрын

Reset and copy looks successful and it works fine for the very first time when I first press the button, but then it "forgets" the code and never works again unless I repeat the whole procedure. Any idea?

@anamemeteau1857 7 ай бұрын

I have the same issue!!!

@wilberthiebert5075 5 ай бұрын

Your remote ist rolling code, so you must buy other remote that can clone it.

@randolphsnyder1505 Жыл бұрын

Managed to copy,however the cloned fob will only do 1 function ,open gate only,no stop or close.Any ideas ?

@sarai7512 Жыл бұрын

Mine isn’t doing any

@wilberthiebert5075 5 ай бұрын

@tif974 Жыл бұрын

When reseting codes. What did you do different between the correct and the wrong way ?

@jonosmani9364 5 ай бұрын

In the correct one he let the first button go after 1s

@tif974 5 ай бұрын

@@jonosmani9364 thanks !

@Anatole_Piano 14 күн бұрын

I bought several copies of this exact same remote control. A few of them work but the others aren’t opening my gate. I don’t get it. Can anybody help, please ? 🙏🏻

@charlie58ize 2 жыл бұрын

My remote has only A B C and it’s stopped working but light coming on. Cannot pair with door

@karlas2546 Ай бұрын

I have the blue control as a copy and I do all these steps and it seems to be ready but it doesn't work

@qiachip Ай бұрын

I am glad to answer your question. Because different manufacturers may have different settings, the operation of the video is for our brand of products. Next, in response to your question, we need to clarify what the failure phenomenon is. This way, we can distinguish the specific problem. For example, if the remote control is copied successfully, but the receiver cannot be operated, it is very likely that the previous remote control has a rolling code, and the copied remote control cannot copy the rolling code, which leads to this problem. I hope to receive your feedback, confirm the brand of the product you purchased, and then describe a more specific phenomenon, hoping to help you solve the problem.

@sweatvallyhigh 5 жыл бұрын

What battery does this remote use? I got one from from Wish with no battery or instructions.

@qiachip 5 жыл бұрын

sweatvallyhigh can you send us the link where you purchased your remote control from?

@qiachip 5 жыл бұрын

Since most of the remote control just have the same outlook but most of them are not using the same battery, the battery we are using on the video are lithium CR2032. Even copy code remote control uses various battery.

@sweatvallyhigh 5 жыл бұрын

Best I can tell a 3V button cell the size of a US nickel but 1.5 times the thickness would work. I need to head to the store, but it's 20 below right now.

@qiachip 5 жыл бұрын

sweatvallyhigh the following link you’ve sent us isn’t one of our product. And we do not have an identical product for it, so I don’t really have a clue. I think the best way is to just ask the seller which battery they are using.

@shantecarroll9783 5 жыл бұрын

27a

@alwave 4 жыл бұрын

Please do not buy but if you are watching this its too late. It does not work. You can keep looking at all the videos you want, it simply does not work.

@vebez5993 3 жыл бұрын

It’s because you have a different model genius

@1988nProud Ай бұрын

Lmao before buying did u open the remote to figure out chip hz? Also this only works for "dumb" or lowtech pairs that well remain static.

@sunflower6434 3 жыл бұрын

Does it have to EXACTLY the same type of remote???

@qiachip 2 жыл бұрын

At least the same working frequency

@Gr8Talk 3 жыл бұрын

Done this over and over - no result. Am guessing the supplier knows this and don't care?

@AhmetElhann 10 ай бұрын

I did everything accordingly, yet after copying, when I press the button it doesnt flash at all like the copying is not successfull.

@obi_Vision Жыл бұрын

Not working on ACM EAGLE TX2 ,only working one time and no more working.....WHY

@Tommy-gm7uo 3 жыл бұрын

Will this work if the original fob is not the same brand and model?

@qiachip 3 жыл бұрын

You can try

@yyyyyc 6 жыл бұрын

Hi, I have the same look alike remote control, with Blue led. I cannot reset it. I cannot get the led to blink, not when I push A and B together for several seconds, not when I push C and D together for several seconds, and not when I push a single button for a long time. Is there a possibility the remote is blocked for programming? Thank you

@qiachip 6 жыл бұрын

Hi, first you need to change battery and make sure it works. Second, you could try this step: Press B and D together. If the second method doesn't work, try to clone your original remote to see if there is light.

@yyyyyc 6 жыл бұрын

Hi. Thanks for your reply, Well, The battery is fine. I tried the B and D combination. It does not work. (also A and C combination). I'm afraid I did not understand what you mean by "try to clone your original remote to see if there is light"

@qiachip 6 жыл бұрын

As you could see in the video 1:42, the remote blink when you program them with the original remote. It was because the duplicator receives signal from your original remote, so it blinks.

@sergiotomas1191 3 жыл бұрын

same problem here and have tried all.

@Sdaniels3152 3 жыл бұрын

Did you get to clear the memory? I am trying with a Blue led remote too.

@baobaolovely 3 жыл бұрын

I've done it right but it doesn't work I can't open the gate. Can you help me?

@kuhne 5 жыл бұрын

Hi. I bought 11 of these. It’s exactly the same as this one but the light is blue. I tried resetting every single one and the reset works but when I try to clone the remote it never learns the old remote. I tried with all 11 of them and none works. I tried with 3 different garage remotes and two tv remotes and it never learns the code.

@richarda4115 5 жыл бұрын

Put them very close together and hold the button on the duplicator and hold it on the original

@lifeisstr4nge 7 жыл бұрын

What should i try if resetting worked, copying worked but the boom barrier only accepts the code once? Then my copy does not work again.

@MoAli72 Жыл бұрын

Sounds like you need a 'rolling code' remote.

@zulfikranzulmos4066 4 жыл бұрын

Why u show wrong 😅😅

@gonzaloperal5512 Жыл бұрын

I resetted my new remote and copied the old one. Then copied the button on A,B and C. The garage responded to each button once and then they never worked again.

@Sorjen108 Жыл бұрын

I got the same issue, did you find any fixes?

@MoAli72 Жыл бұрын

@@Sorjen108 Sounds like a 'rolling code' remote is what you need. This tech basically sends a new code in transmission each time to prevent attackers cloning the transmission.

@Sorjen108 Жыл бұрын

@@MoAli72 Yes I think so, do you know where can I get a rolling code remote please?

@virgiliofi Жыл бұрын

Hi! I have the blue led light remote. Once I programmed the new remote, it looses the coding after a couple of minutes. What can I do? Please help!🙏

@andrelaishong577 8 ай бұрын

Hi, did you find a fix im having the same issue,thanks

@virgiliofi 8 ай бұрын

@@andrelaishong577 Hi Andre! No, I ended up buying a new one 😔

@wilberthiebert5075 5 ай бұрын

These remote can't clone properly a rolling code. Or clone one time in A button and B button, A to open and close and B to stop.

@ozgurteyhani4527 6 жыл бұрын

is there any way to clear only one button?

@qiachip 6 жыл бұрын

Hi, when you clear code, all the button's code would be erased.

@sinergija1236589 4 жыл бұрын

When I press both bottons A and B together light is always on no matter how long I'm pressing together. Light is always on, without flickering as much as I'm pressing bottons. Please how can I clear the memory and program my remote? Thanks

@tamkepa 3 жыл бұрын

Did you find a fix? I have the same issue

@ChrisEscape 3 жыл бұрын

@@tamkepa Did you? same problem

@wattage2007 2 жыл бұрын

@@ChrisEscape I've seen other models of these on which you need do the A and B button press but release the B button while keeping the A pressed. Then, with the A button still pressed, 3 slow presses of B again then that's it cleared. I just find it incredible they make these amazing products then absolutely fail to explain how they work.

@Wen-hz9mb Жыл бұрын

Why won’t mine clear ???

@davidteixeira7390 Жыл бұрын

Can I erase only C and D anda then reprogram? I can't loose A and B?

@wilberthiebert5075 5 ай бұрын

I will erase all button.

@davidr.montgomery8919 5 жыл бұрын

I don't have a way of making a video. I followed your directions carefully. Well, you have your money. Thanks for nothing. I just want my money back. No wonder you say all sales are final.

@qiachip 5 жыл бұрын

Can you tell me what went wrong with the product? May be I can fix it for you according to your description.

@sarai7512 Жыл бұрын

@@qiachip hello, mine as well didn’t work ( the door DIDNT open) The reset and copy code was done correctly but at the end the remote didn’t did it job. Please help whats the problem

@nik0las1 3 жыл бұрын

Mine is not cleaning.

@marcfonteyn1434 2 ай бұрын

Sorry but is not working with me !!! I followed all te steps but at the end therse is NO ligth annymore ???

@qiachip 2 ай бұрын

I need to confirm: Can your cloned remote control copy another remote control? If not Then you need to understand a few questions: 1. Can the frequency of the copied remote control copy another universal remote control? 2. Are their encoding formats the same, such as EV1527 or PT2262, etc. 3. Is the ordinary remote control or the copied remote control in encrypted rolling code mode? Finally If you buy from us, you can send a picture of your remote control to customer service We can help you confirm the above questions through the picture! Hope it helps you

@fabianm2980 6 жыл бұрын

Reseteo el mando y borro todas las señales. Luego intento clonar el original. Funciona el mando durante 5 segundos luego deja de funcionar. ¿Saben por que?

@qiachip 6 жыл бұрын

Hello, we assumed you did not have a entire procedure of cloning. First press the key fob earlier than the original remote.

@reviewbangroy1858 4 жыл бұрын

Buat remote mobil vios gmn caranya

@ilhanozgan 4 жыл бұрын

Not working with my Honda minivan remote,junk

@Lohtia25 3 жыл бұрын

Copying not working tried lot of times

@eusebiolucas1017 2 жыл бұрын

Programarlo

@javyqv 3 жыл бұрын

I bought a remote just like that but i am unable to place it in learning mode even if i let the 2 top bottoms hold at the same time it wont work any sugestion

@bharathchand4154 3 жыл бұрын

Same here. Just doesn’t work

@carlenebourke7736 7 жыл бұрын

I have tried what you suggested but my remotes still won't reset. HELP!!!!

@nateepongteerarat8013 6 жыл бұрын

Carlene Bourke me too!!!!!!!!!!

@ericmccormack8678 6 жыл бұрын

Don't work

@thepharaoh2832 5 жыл бұрын

Me too, non of that works

@neilcvernon6957 2 жыл бұрын

Ant get mine to Flash to reset :(

@zulfikranzulmos4066 4 жыл бұрын

Haha why would u need to show wrong way and correct way.. Just show correct way simple 😅😅

@MoAli72 Жыл бұрын

It's quite shit we have to reset the whole remote every time we want to clone a button or something.

@davidr.montgomery8919 5 жыл бұрын

Personally I believe this is a scam and a farce. While I can get this to clear, I cannot get it to set up the remote for ANY key. I am a retired computer programmer and I know computers very well. I am just before going to Better Business Bureau and lodging a complaint. I don't need no bunch of baloney. I need to know how this works and why it won't.

@qiachip 5 жыл бұрын

The copy remote control only works with a few type of code, can you make a video of what you did? Thx.

@CaribbeanCryptoz 4 жыл бұрын

I agree. Ot says what frecuency amd thats it. Mine doesnt work fro my kia soul. Its a scam.