Quick Rc Boat Bash Oxidean Marine Dominator - 4214 (3) Prop, XLX2 Hydra, Tp Power,

Рет қаралды 1,094

Ай бұрын

Use BIGBISTHEMAN (all caps) 5% 0FF ANY HULL & HARDWARE
oxideanmarine.com/search?type...
DOMINATOR HULL & HARDWARE
oxideanmarine.com/products/do...
CNC 4214 (3) PROPELLER
www.offshoreelectrics.com/pro...
GNSS PERFORMANCE ANALYZER GPS
www.offshoreelectrics.com/pro...
HYDRA XLX2
TPPOWER 4060 2080
Ds servo 25kg
Quasar rx/tx
XLX2 HYDRA
www.avantlink.com/click.php?t...
B LINK
www.avantlink.com/click.php?t...
.187 FLEX CABLE
www.offshoreelectrics.com/pro...
OCTURA 3/16 SLEEVE BUSHING
www.offshoreelectrics.com/pro...
EXTERNAL WATER PICK UP
oxideanmarine.com/products/wa...
OXIDEAN 4514 STAINLESS STEEL PROP
oxideanmarine.com/products/45...
VENOM CARBON EPOXY
www.ebay.com/itm/115221976267...
XLX2 HYDRA
www.avantlink.com/click.php?t...
QUASAR RX/TX GPS
oxideanmarine.com/products/ox...
SMC HCL-HP 11300mah 150C 4S
www.smc-racing.com/index.php?...
SMC 6500 150C 3S
www.smc-racing.com/index.php?...
SMC HCL-HP 7600 150C 6S lipo
www.smc-racing.com/index.php?...
Thanks for watching ironclad rc tinker test and tune everything
Personal contact information ironcladedout@gmail.com
Facebook
share/eknUp8...
TikTok
www.tiktok.com/@ironcladrc?_t...
Instagram
ironcladedo...

Пікірлер: 20

@ForestPettit-jb7jl Ай бұрын

I have one too, my favorite boat, man good driving it's quick.

@scaleworksRC Ай бұрын

Good stuff.. smooth as silk and flyin' on that water! 🚤💨BG4L

@jimstone5339 Ай бұрын

Just got my new bj24 and it's better than I thought. Yahooo

@jamesatkinson7517 Ай бұрын

3 blade seam smooth on monos crazy torque steer on riggers for me at least

@minochercowasjee Ай бұрын

Big B , thanks , it’s screaming !!

@jonathandemaria1865 Ай бұрын

Yea B😎

@dnacannotchange Ай бұрын

.... Is that 600 sandpaper on the bottom of the hull???

@peteroosterhoff8850 Ай бұрын

Wish i could have done same today. But unfortunately boat is not ready. Working on a small bar now and having a small brake from the sun since its bloody hot... 🥵

@IRONCLADRC Ай бұрын

Tell me about it, it's 96°f today with the humidity, and it feels like 100+. No boating for me today

@peteroosterhoff8850 Ай бұрын

@@IRONCLADRC Ok, then it's even 5 degrees warmer at your place. These were the first reel warm days and not used to it yet since weather has been mostly 10-15 degrees lower. I really need to adjust to these conditions and also have to use medicine that make it a lot worse. But hè, every hour i put into it makes the end come sooner...

@boatwerks Ай бұрын

SCBG4L

@tl2177 Ай бұрын

Tried to contact you via your listed email but it was returned. What is your preferred non-KZfaq contact please.

@IRONCLADRC Ай бұрын

Face book is a good place to contact me.. ironclad rc

@doublefourz Ай бұрын

I'm running an average speed on ovals Total distance 1 mile 6 laps 46 mph Oxidean dominator 4s 2050kv Drained packed to 10% Average Temps motor 112, battery 135, esc 105 Average run time 78 seconds From what I've seen.. I don't think that is fast enough to be competitive. Must hone driver skills = drive more boats 😂

@IRONCLADRC Ай бұрын

Sounds like you need a higher kv Motor or prop up a little bit with 4s wired in parallel

@doublefourz Ай бұрын

@@IRONCLADRC running single pack 4s Propping up was what I was about to do. Running an oxidean 4519..running super loose and dry.. So I'm a bit hesitant to throw on the next size I have which is an octura M447 Shortened Rudder.. Almost no drag.. 46 mph is what I'm getting as an average speed in completing the 1 mile.

@IRONCLADRC Ай бұрын

@@doublefourz that m447 is gonna be awesome on that boat I've run that prop on mine! Just watch temps that first run especially the first run.

@doublefourz Ай бұрын

@@IRONCLADRC ALWAYS.. That first run is so critical. In a situation like that when there is an unknown variable thrown into the mix. I do 1 lap untape check and retape.. About 4 or 5 times before I start any tuning. Balanced sharpened and ready to go. I'm looking to cut 12 seconds off my total time. 🤦‍♂️🤦‍♂️🤦‍♂️🤦‍♂️