I have one of these and the range and performance are very good. Much better than my previous DSMX clone receivers.

Hi, I bought 2 of these and both failed to bind. I am in the UK and the protocol you use is different, this had me scratching my head and I updated the firmware (radiomasterrc.freshdesk.com/support/solutions/articles/64000257762-r168-receiver-firmware-update-procedures) and it still failed after the update. The fix (EVENTUALLY) is that my TX16s uses FrSky LBT(EU) protocol, NOT the D16! Once I found this out, from Radiomaster. One of my receivers worked, the receiver I had firmware "upgraded", I had to install V1, not V2! Then that then worked no problem. Keep up the good work :)

For the price it's incredible, I'm also interested in the other Rx Radiomaster are selling. Thanks for the video.

In the mode options, I can only choose from FrSkyRX, FrSky X, FrSkyX2, FrSky L. The option "FrSky" is not there. And I can not bind to my receiver R168. Do you have an idea what the problem could be?

Thanks & regards ...

Thank You SOOOOOOOOO MUCH for this Video. I was just about to give up ever having a radio system I could trust, or even use. I tried Taranis X9D PLUS SE, TWICE, and both were absolute GARBAGE!! They NEVER Worked at all, even with FrSky receivers. Then I tried RadioLink which worked okay, and Then------ RadioMaster. I have had fits trying to bind the R168 Receivers, but now---------- IT WORKS BEAUTIFULLY !!! THANK YOU , THANK YOU, THANK YOU !!! Can you tell me where I can buy that module you are using to set up , and test your radios??

I would like to know how to use the SBUS. I have never used SBUS so need to know everything about it.

It might be a dumb question, but can you also use a battery capacity checker and connect it to the battery while the rc plane is powered on? And then fine tune the battery voltage like you did in your video?

If I want to run say a 6s battery. Could I just build a voltage divider with a couple of resisters and bring the voltage down to a workable voltage. I'm thinking a couple of 100K resisters so the drain is negligible and pick off the voltage from the center.

Thanks for the vid John, that was gonna be my next Rx purchase. Definitely interested in seeing how it performs on the plane, I am sure it will be good. I do have a question, as usual. The power from the flight pack comes from where, the positive on the balance lead or a wire soldered into the main power from the ESC connector?

Have you noticed in the upper case of the receiver that thevoltage indicated is 4.5-6 volts? But in the instructions to bind it, the range is 4.5-8-4 volts, and that is why I bought it¡¡¡¡

Do you do a fine tune as well on this rx? Or should you on all recievers? Great stuff Thank you.

I’m following your directions, but my r168 receiver isn’t going into bind mode when I hold down the bind button and plug the battery in. Does the module status on the tx16s matter? How do I change that line?

Whats the difference of us or eu version

Hi .. i just purchased this radio but i don't no if any 18650 batteries can work? I have 2x Panasonic ncr18650bd.. are they ok ? Cuz i got confused with 3.6v and 3.7v thing cuz all batteries rated as 3.6v So is Panasonic ncr18650bd good for it ?

Hi, do you have the latest firmware release of that R168 ? can you provide it? thanks (cause seem its impossible to find it )

Thank you. Question: what can you do with the RSSI pin on the R168?

Also with the R168 receiver that is 8 channel but with the SBUS it is 16 channel how do I get the other 8 channels with the SBUS??

i cant bind tx16s and r168 none have Frsky D16. only have FrskyX D16, FrskyX2 D16

Not first!

I got an email from Banggood on Saturday saying that my TX16s has SHIPPED! It’s still in China but it’s on its way.

I almost bought a couple of these when they came out until I realized they are only good for up to 18v which does me no good for 6s lipos. Rm dropped the ball on this one by basically excluding the entire heli community.

First!