Rago Fabrication LED Bar Wiring on a 5th Generation 2016 Toyota 4Runner. To purchase Rago Fabrication brackets or products, please visit www.ragofabrication.com
Пікірлер: 35
@ajrhoads936210 ай бұрын
Environmental connectors and heat shrink would have made this a lot better.
@fallissimoghost19575 жыл бұрын
Thank you so much for showing the blank wires from the light bar, & connecting it up.. So much detail 😎.
@MomentumTV2 жыл бұрын
This was the first one I found that the person made a real attempt at good wire management and concealment. Drives me nuts when the people just zip tie them up and down and call it a day lol
@ColoradoStreaming5 жыл бұрын
Testing the connection before heating the shrink wrap it is nice tip, I would not have thought of that one.
@paul1mdrn5 жыл бұрын
Good vid! I used a continuous piece of shrink tube, spraying 303 inside helped the wires go through easily.
@DashCamJournalsPH5 жыл бұрын
love those brackets! Thanks
@ML-mx1py5 жыл бұрын
Are your brackets causing any wind noise from the door jam when driving 60+?
@DashCamJournalsPH5 жыл бұрын
@@ML-mx1py I don't have these yet on my rig but I am looking for one that would fit my triton. does this bracket cause wind noise when driving?
@ML-mx1py5 жыл бұрын
@@DashCamJournalsPH It sure does. i would suggest getting brackets that mounts on top of the roof where the roof rack tabs are placed. i am so close to just ditching these but my rig will be scared with 4 holes ):
@DashCamJournalsPH5 жыл бұрын
@@ML-mx1py Thanks for the input mate, I am considering to purchase a top mount roof bracket as well but I am scared to drill some holes on my rig. :) I am looking into some magnet brackets but this might get my led bar stolen when I parked in a public space.
@russellcupples21706 жыл бұрын
Very detailed ,Thank you
@FedericoAllegretti3 жыл бұрын
Remove 2 cm of insulation from both sides of the wires. Twist 1 cm of each end of the two wires, THEN join togheter the ends. Twist them togher. Apply flux and solder
@DashCamJournalsPH5 жыл бұрын
are those LED brackets universal fit or is it custom made for your rig type?
@1badEK5 жыл бұрын
How is the bar held in place? Does it need to be drilled to the roof with the bracket?
@gliderider19613 жыл бұрын
Use flux to "tin" your wires prior to soldering and your connections will be MUCH cleaner (plus, they won't require as much heat to solder). OR, you could use shrink connectors with solder built in and it would cut your work in half. (Also, FYI: The "L" in "solder" is silent. Just sayin'...)
@ML-mx1py5 жыл бұрын
anyone else having any issues with wind noise coming from the door jam where the bracket sits? fixed the light bar whistle noise with cowles edge trim.
@Jericho_bella5 жыл бұрын
I would love to share photo of my 2015 4runner rago light bar bracket on ur website
@user-ck2pi5vh1b2 жыл бұрын
Did you guys discontinue this light mount?
@RandyStClair-zq3ue7 жыл бұрын
How can I get the switch to be one of the blanks that's already waiting flat
@sideeffects65703 жыл бұрын
The one and only thing I wanted to know was HOW you Installed it to the roof 👎 and you never showed it
@logansmith43684 жыл бұрын
What kind of mounts are you using ?
@RagoFabrication4 жыл бұрын
Logan Smith u can find them at ragofabrication.com. They are stainless steel.
@dkla804 жыл бұрын
Nice setup. Do you make this for a 2004 gx470?
@RagoFabrication4 жыл бұрын
Donnie Go we don’t
@ernestmartinez82557 жыл бұрын
Will those ragos fit a 2015 50 inch curve?
@hh1h_3347 жыл бұрын
not on a 1st gen tacoma
@kirtswarthout28564 жыл бұрын
1, he should be using insulated connectors, 2, he's using a fork connector with a push on connector....this guy doesn't know what the heck he's doing..
@jlentz34 жыл бұрын
"Crimping" with a multitool pliers instead of a crimper.
@MagargeeFilms3 жыл бұрын
Here’s a great explanation of installing a light bar kzfaq.info/get/bejne/Z9dkqr2i3tmUnGQ.html
@orlandosorinopris677511 ай бұрын
public danger. do not try this
@dave10963 жыл бұрын
the wiring at the light and copious amounts to tape is not well done. Improper fork connectors at the light, not using a crimping tool. lazy option and should not even be in your playbook for your customers. My dad would punch me in the neck if I pulled that
@przemonl10564 жыл бұрын
Omg! I don't recommend anybody this solutions :O 1. You cut bar cables just to put this fast relase connectors on it? 2. You know why ppl invented waterproof connectos with good isolation? 3. You know how many amps swinging in this cables when its on? 4. You cut cables one more time making it 1cm short just to solder it again? 5. Do you know what is minimum thickness for this amperage? :SSS