Ram 1500 Axle Shaft and CV Replacement

Рет қаралды 56,028

Жыл бұрын

#ram #DIY #axleshaft
Time Stamps and Links below!
Passenger Axle Removal form truck 11:20
Axle Teardown and Rebuild 17:34
Passenger Axle Reinstall in Truck 40:32
Passenger Front Reinstall 44:00
Driver Side CV Removal 50:33
Driver Side Axle Install 51:25 (didn't realize other camera was off) Seal installs like passenger side.
Driver Side CV Install 52:46
Driver Side Reinstall 54:08
Refill Front Differential 56:00
Final Test Drive 58:45
Thank you for watching! I have included links to all products. Just being helpful. Here are the links to the Ram 1500 Front Intermediate Shafts or Stub shaft or Stub axles, or whatever you choose to call them. There are others to choose from but this is the one I bought. Second, is the Heavy Duty Extreme Temp CV Axle Shafts by TrackMotive with a limited lifetime warranty. Once again, there are many to choose from but this is the one I choose. Finally, the Mevotech Supreme Front Wheel Bearing and Hub from RockAuto.com with a 5 year warranty. You can also get from Amazon.
Intermediate/Stub Axle kit:
amzn.to/3tUStKl
HD CV Shafts:
amzn.to/3wQYsOx
Wheel Hub Assembly:
amzn.to/3Dva1iu
Black and Decker oven used to heat bearing:
amzn.to/3LnUTqe
This is my 2014 Ram 1500 Big Horn, should be the same for years 2012-2022, we are replacing the old worn out axle shafts/intermediate shafts and CV axles. I was going to include the Wheel Bearings in this video but decided to leave them out because of the length of the video already. This is not a hard job and it is mainly just time consuming. Make sure you have BIG 90 degree C-Clip pliers!

Пікірлер: 190

@jeffglasman19 8 ай бұрын

Just a tip from a tec. If you tighten up the axle nut with a Impact gun it can damage the wheel bearing. And how it does that is, it pounds the balls into the races and and makes tiny dents, which cause bearing failure . SKF will void warranty if they suspect that was done to a new bearing, and premature failure occurred. They have to be hand tightened and torqued to specific specs , SKF has a on line torque specs info page for all makes of Vehicles.

@DavesBuild 8 ай бұрын

Great point! I'm going to pin this comment. Thank you for the feed back!

@markt800 7 ай бұрын

@@DavesBuild were you having any highway shakes before the job?

@DavesBuild 7 ай бұрын

@markt800 I had a slight vibration that I couldn't get rid of. Well it's gone now after this repair.

@wsvitak Ай бұрын

11 hours one day, 6 hours the next. That’s how long I tried to bang, pry and pull the CV axle out of my Ram. Spent hundreds on tools and watched tons of videos. I ended up cutting the cup off the axle, leaving just the stub attached. I put a 3 jaw puller on there and attempted to remove with an impact and it didn’t budge. I ordered the differential shaft and will be attempting this tomorrow. Thanks for the video.

@aubreyseed7337 11 ай бұрын

I’m about to tackle this same job on my 2016, this video was incredibly informative and helpful! Thank you so much for making this video and answering everyone’s questions!!

@DavesBuild 11 ай бұрын

Good luck! Not too bad of a job.

@jonhoward1911 5 ай бұрын

Where do the o rings go

@jab287 Жыл бұрын

Just did this on my truck. Thanks for the help, dude. If anyone is having trouble putting the larger bearing on the stub shaft. Try tapping the bearing into the housing first. Sense I didn't have a way to heat the bearing properly. I just ended up using a big socket and fitting it into the housing, then i taped the shaft through the whole housing. So far, so good.

@DavesBuild Жыл бұрын

Glad it could help you out! Thanks for sharing your process as well. Like they say, there's more than one way to skin a cat. Lol.

@anthonycondon1132 Жыл бұрын

Great video. Going to come in handy next weekend. Truly appreciate you taking the time to document your repairs

@DavesBuild Жыл бұрын

Thank you! I don't mind sharing my pains... lol

@RickySlatton Жыл бұрын

Thanks once again Dave for a good video 👍🏽

@MrMcNorm Жыл бұрын

Thanks, Dave! Had not been able to get a suitable explanation of the passenger side, this was great! :)

@phprofYT 3 ай бұрын

Thank you. It's on my spring list. Nice design, RAM.

@calvinhobbs89 Жыл бұрын

Great video an insight , thank u for your time an patience. Sockets are great choice for installing bearing an removal in a pinch never hit the inside race only outer if your going to ever think about using that bearing again

@edw7586 Жыл бұрын

Thank you Dave, excellent video great job

@kennethperian4370 11 ай бұрын

Great job showing and telling and getting it done,I am watching you to start on my 1500 ram single cab 2008 tomorrow maybe. Well thanks again for showing telling and have a great day see ya next time see ya bye.

@DavesBuild 11 ай бұрын

Thank you!

@ksfishingadventures Жыл бұрын

Probably the most helpful video out there to replace this shaft ! Thanks

@DavesBuild Жыл бұрын

Thank you! I appreciate the feedback!

@WesleyReese Жыл бұрын

Thank you Dave for the great detailed video, getting ready to order parts and work on another project with my 72 year old dad. Amazed that my stub drive rusted out and my new cv axle ate all the teeth of the stub drive when the truck is only 3 years old.

@DavesBuild Жыл бұрын

I'm glad the video could help ya out! Let me know how it goes.

@510motorsports5 6 ай бұрын

Great video man this was so helpful thank you

@james589 Жыл бұрын

Great job, Dave! Really appreciate all the detail in this video. Just found out mine are in the same shape yours were. So, I'll be doing the same project soon. Also, thanks for the update on the ball joints, I have the same brand in my Rockauto cart!

@DavesBuild Жыл бұрын

I appreciate the feedback! Thank you! Now if I can get my camera skills better!Good luck on tackling yours!

@Mark-km7uo 5 ай бұрын

Great video! I gotta do this next !

@tbk7001 Жыл бұрын

Very good job . Thank you . Best regards from Sweden.

@DavesBuild Жыл бұрын

Thank you for the kind words! Take care.

@Breck724 Жыл бұрын

Solid video Dave, I am considering tackling this as my CV attachment splines are toast too!!

@DavesBuild Жыл бұрын

Thanks Troy! I'm still trying to get the hang of this video stuff. Lol. It's not too bad of a job.

@Breck724 Жыл бұрын

@@DavesBuild You’re welcome, I’ve watched a few of your videos and we share some of the same issues with our Ram 1500’s. I like your filming, don’t let anyone discourage you!! I really like your use of the freezer and toaster oven; who needs a press!!

@NolanDman Жыл бұрын

I had just made my account just too comment and tell you, you are a real one! Great video. When I saw you use the grinder I knew on that passenger side inner shaft I knew I wasn’t the only one feeing the pain of a seized cv axle. I was hoping that inner shaft would come out the opposite way 😂 going too cut it off the same way. Enough is enough lol

@DavesBuild Жыл бұрын

Thank you! Enough was enough! 😆 No time to mess with it forever, gotta do what you gotta do! Thanks again for the comment brother!

@alexgrech4420 3 ай бұрын

After hear the horror stories of the right shaft seasing up your video help me relax after the way you cut it off thank you

@wsvitak Ай бұрын

Fucking nightmare. I started Saturday morning at 10am and didn’t finish until Monday at 6pm. I’ve been working on cars for over 20 years and never have I been defeated like this. Had me questioning my life choices and my decision to ever touch a tool in my life. Ruined my weekend, Father’s Day and my family’s weekend. FUCKING NIGHTMARE.

@alexgrech4420 Ай бұрын

Did you unbolt the aluminum case and cut axle off with a angle grinder

@lsxobs3709 Күн бұрын

@@wsvitak So what was your solution?

@jacquelineserret6055 Жыл бұрын

Thanks 😊 for videos 📹 is so good 👍 Thanks 😊 🙏

@bryaniskoo Жыл бұрын

Thanks! This bad ass!

@mikeh2772 7 ай бұрын

Good video, thank you sir.

@tannerhoward3817 Жыл бұрын

I got a small leak from between the arm of the diff and the actuator housing after putting it back together. Wondering if I need to add a little liquid gasket?

@jacobmansker9624 11 ай бұрын

I replaced my cv axle on my ram and noticed the seal on the intermediate shaft oscillating in and out when I turn the wheel. Do you think replacing the intermediate axle shaft will fix it or do you think I have bigger problems? My trucks been making loud growling sounds like a wheel bearing but I’ve replaced the front hubs and rear bearing to no effect.

@gabrielmckinnon5862 6 ай бұрын

Does the second ser clip that goes around the internal intermesiate shaft set into the housing. Seems like not much of a groove on the shaft? Thanks for the video!!

@vincedominguez1210 6 ай бұрын

@ 44:22 what’s that black sleeve you put on over the stub. Mine keeps slipping out after I put it in. I’m gonna replace the snap ring right now try to get it to stay in. I just don’t have that black sleeve. 😢😅

@shoes121255 4 ай бұрын

I did this a few weeks ago on a 5th gen ram. As far as i know the parts are the same. Struggling now with no 4x4. Not sure if its related to something i did. Can the lock ring that moves via the actuator over the shafts be installed either way, or is it directional?

@gabrielmckinnon5862 6 ай бұрын

Did you wait for the black gasket maker to cure before testing it out? Thanks

@charlesbrodd6830 Жыл бұрын

What brand did you go with for replacement parts: stub shaft kit especially? Where did you source the boots to seal the stub-to-cv splines??

@DavesBuild Жыл бұрын

So the stub shaft kit was sourced from ebay, and included the boots, seals, shafts, and dirt shields. All the other parts came from Rockauto.com

@michaelmahoney5885 Жыл бұрын

Great video I have the same issue

@knifeaddict1014 Ай бұрын

On my 2011 can’t find where to add gal after replacing the CV axle, I see a rubber cap with a white match up line. Could that be it?

@brianlawrence9493 7 ай бұрын

Any one know if the kit will fit a 2020 ram 1500 not the classic? All the kits I find seem to say they fit the classic and I can’t find the one for my truck but they look the same.

@justinhayes4426 6 ай бұрын

Did your axle keep walking off of the stub shaft?? Mine does and I’m thinking may be wheel bearing

@josesamaniego2505 Жыл бұрын

to find out if it is failing, you should find something like metal ground from wear, I already disassembled it but everything looks fine, I don't know whether to put it back together or whether to change the parts

@DavesBuild Жыл бұрын

What I found first was what looked like rusty water splash under the truck inline with the spin of the axle shaft at the cv. Then I shook the cv axle and found the ton of play.

@oak8728 Жыл бұрын

Where does the 1.5” o ring that came in the passenger axle shaft go? I am looking at 44:13 and do not see yours installed.

@DavesBuild Жыл бұрын

You are correct. I did not install it because I am using the boot cover. I probably should have installed it along with the boot but I'm keeping an eye on it. Good catch.

@oak8728 Жыл бұрын

For anybody with the EcoDiesel, 1 of the 4 bolts to the axle shaft housing is about impossible to get to. The oil pan looks to sink lower w/ more stuff in the way and I cannot get a socket on it. Hoping to not have to drop the diff. Great video Dave a lot more hemis out there than 3.0s.

@DavesBuild Жыл бұрын

Great information. Unfortunately it sounds you may have more fun than I did. Good luck with it.

@josephdossantos9274 5 ай бұрын

You definitely need the right tools for this kind of work. It is going to make your job easier. Other than that, you still got it done.

@chasegagnon9755 Жыл бұрын

Where do you order these kits I have a new body 2019 looking to order the kit anyone have some details for me ?

@zacritz7639 Жыл бұрын

I'm real curious if these kits work with the new body style. All of the listings appear to show it for the 4th gen/ram classic only but the differential itself looks identical

@DavesBuild Жыл бұрын

The kits should work from 2012-2022+ from what I found. Hope I could help. Sorry for the late reply. Seems I had a few get by me.

@looneyludy4495 Жыл бұрын

Does your new CV axle still wiggle by hand? I replaced mine and the axle shaft and they still have some play in them.

@DavesBuild Жыл бұрын

Very very little. Not much at all.

@wsvitak Ай бұрын

I should have watched the part where you froze the shaft and heated the bearing. Spent an hour just tapping evenly all the way around, trying not to damage it. That worked better than I could have imagined.

@alwayza9er 11 ай бұрын

Is this the same for 2021 ram 1500?

@dylansirois8768 Жыл бұрын

I wanna say thank you very much this will save me a ton of time. I spent 2 days trying to get the axle off to no avail. Tried everything. Twisted up 2 pulley pullers in the process. That thing is on there! Where did you get your replacement parts? I might buy from ebay but im skeptical about the quality.

@DavesBuild Жыл бұрын

I'm glad my video could help! I posted some links in the description. I'm at 250k miles now and still doing great!

@Eclipse1997GSX 9 ай бұрын

What kit did you go with? I've found kits 3.55 ratio but, rear in mine is 3.21 I'm assuming front should be the same?Trying to make sure I order the proper kit Thanks

@DavesBuild 9 ай бұрын

I also have the 3.21. They are the same kit. I have a link in the description for the kit. Thanks for reaching out and checking out the video!

@LuisSanchez-jk1sn Жыл бұрын

Thanks a lot

@DavesBuild Жыл бұрын

You're welcome!

@LuisSanchez-jk1sn Жыл бұрын

Very helpful 👌

@johnstrawser420 9 ай бұрын

Will the fluid from your differential go to where the shifter locks in the passenger side wheel?

@DavesBuild 9 ай бұрын

Yes it will.

@gabrielmckinnon5862 6 ай бұрын

Any idea why there was 4 seals?

@bartekjakubiec706 Жыл бұрын

Hi. Great job. A have question. Do we need to change oil whit this job? Thx👍

@DavesBuild Жыл бұрын

I would definitely change it while you are already into it. I wouldn't try to reuse because the chances of contamination of the oil is so high.

@luisgalindo7234 Ай бұрын

If I have to replace my cv axle boot do I also have to do a differential fluid change like yourself ?

@DavesBuild Ай бұрын

No but may need to be topped off.

@josesamaniego2505 Жыл бұрын

I hope I can do it too. The dealer told me 4,800 to replace those parts

@DavesBuild Жыл бұрын

It's really not a bad job. I got faith you can do it!

@r.a.wfabricationcustoms8009 Жыл бұрын

Im getting ready to do this on my 17 Ram, pass side is shot. how are the intermediate shafts from amazon holding up so far? how many miles do you have on them? thanks for the video very helpful.

@DavesBuild Жыл бұрын

They are holding up great. I'm at about 15,000 on them now with no issues so far!

@desireecilenti9588 9 ай бұрын

My 2017 Ram 1500 has a bad stub shaft on the passenger side. Is that part still available or do I have to buy the entire axle?

@DavesBuild 9 ай бұрын

There are kits to replace it so there is no need to replace the entire axle.

@satoshibautista7766 Жыл бұрын

Thanks for the video. I did mine exactly the same. Although when driving the first test drive it was perfect. Second day my wife took the truck to work and it started to hop on the hyw. And she liked it home at 20 mph with it whining I'm curious if you know what it could be? The electronic 4x4 mechanism not working properly?

@DavesBuild Жыл бұрын

That's tricky to give an option on. If I had to guess it would be more transfer case related.

@satoshibautista7766 Жыл бұрын

Got the truck home and the cv axle popped off of the intermediate shaft. That keeper ring didn't hold any secrets on it holding in place? Tack weld?

@DavesBuild Жыл бұрын

@@satoshibautista7766 you can try spreading the ring out or ovaling it out a little. Wouldn't tack it.

@Justin12833 Жыл бұрын

Wish I would have watched this before I let a shop that does my work stave up my front diff trying to get the stub shaft out. Then had to buy a used unit. So they never would have got that passenger side out without removing that clip from the inside right? Also are those rubber pieces to protect those shafts open to the elements and I wish I woulda had them do that on mine.

@DavesBuild Жыл бұрын

Correct, that clip must come off before the shaft can be removed. I hate you had problems with a shop. I have a hard time trusting them is usually why I do all my own work. I'll take it to a shop for alignments and sometimes they can't even get that right. Lol

@djhinrg 5 ай бұрын

Looks like me. With lift kit blocking. Just to get there to replace the part, I ended up replacing the part I removed lol

@matulonisw 21 күн бұрын

What’s the size of the diff housing fasteners?

@michaellong7649 10 ай бұрын

I had the same issue on my 2016 ram, I replaced the cv axle that still didn't fix the issue, so I figured the stub shaft needs to be replaced. But now I can't the new cv axle off the old shaft. We've tried just about everything . ???

@DavesBuild 10 ай бұрын

I ended up cutting the stub shaft off to replace it. I couldn't get mine off either.

@michaellong7649 10 ай бұрын

@@DavesBuild I don't want to ruin the new cv axle though

@epicjk5509 Жыл бұрын

Great video. I'm getting ready to do mine. Did your kit come with o-rings? If it did where did you installed them. Thanks

@DavesBuild Жыл бұрын

It did come with o rings, not 100% on location as I wasn't familiar with them. I had the boots so I used them on the shafts.

@jasonsosa69 Жыл бұрын

Would like to know what year was your Dodge ram because I’m having the same issue and I just change the CV axles. Wanted to know how many quarts did you use to add the new liquid?

@nicarocho Жыл бұрын

The recommended oil for it is 75w90 and apparently the oil level is good when it starts dripping from the top Allen bolt 😅 ... kzfaq.info/get/bejne/r913kpCYlrDdcnk.html

@jasonsosa69 Жыл бұрын

Thank u man. U really help me out and I got the job done.

@josesamaniego2505 Жыл бұрын

Excuse me, I have two questions, you put a valvonline brand product on it. I would like to know what it is. And also why did you put a piece in the oven? I thank you in advance

@DavesBuild Жыл бұрын

I use Valvoline synthetic 75w90. And I heated the bearing so it would expand enough to slide over the shaft without using a press.

@josesamaniego2505 Жыл бұрын

Ty sr

@idiocracy5114 9 ай бұрын

Where did you get the rubber boot that covers the part where the cv axle goes over the shaft?

@DavesBuild 9 ай бұрын

It came in the kit. Is it not in the kit anymore? 🤔 I'll check

@idiocracy5114 9 ай бұрын

I found a kit that had them in it, some on Amazon appears not to have them.@@DavesBuild

@garrettsmith6679 Жыл бұрын

Anybody doing this on the ecodiesel, the oil pan sits right on top of that housing and your can barely get that top bolt out and you have to twist and play with it to get the housing to slide all the way off, and then of course getting it back on and getting that bolt in.

@garypeterson7596 Жыл бұрын

that link didnt work for the intermediate shaft, can you reply with a good link?

@DavesBuild Жыл бұрын

amzn.to/3oiKVOO

@JoeAustinMusic 20 күн бұрын

Nice video.. just a suggestion, please use a camera tripod next time. I’m sea sick from the head camera movement sick🤢😂

@DavesBuild 20 күн бұрын

@JoeAustinMusic sorry about that. I have purchased one for future videos already. Thanks for watching, I appreciate it!

@ryanbruegger4522 Жыл бұрын

Will standard axles fit or are the heavy duty needed?

@DavesBuild Жыл бұрын

Standard is fine also.

@americaornothing7770 9 ай бұрын

Did the axles come with the black water shields you installed before the cv axles?

@DavesBuild 9 ай бұрын

Yes they did. Here is a link to the ones with the seals. amzn.to/3MjNzwS

@americaornothing7770 9 ай бұрын

@DavesBuild Thank you very much for the reply, and it being so quick.

@jordanlewis7265 Жыл бұрын

you should be able to knock the cv axle off the stub shaft and out of that case, someties the stub comes too just seperate and put it back.

@DavesBuild Жыл бұрын

I tried to pull it apart, and it would not go. I just said the hell with it all... 😆

@jordanlewis7265 Жыл бұрын

@@DavesBuild i was wondering if you had any experience with seized lower control arm bolts. i took my truck into get aligned and they couldnt do the camber caster bc the bolts were seized. i havent gotten into it yet but have been scowering the net for information for the upcoming battle.

@vekin104 Жыл бұрын

@jordanlewis7265 I do alignments, in those cases, we usually have to torch out the bolts, which generally ruins the arm, so you just replace any piece that is supposed to be able to move. Gotta love the rust belt.

@slothdaddy3315 10 ай бұрын

just changed both my cv shafts on my 1500. well done video other then all the bolts and nuts that where removed have torque spec. not one was put back to its torque spec. The ball joint is set at 40 pounds for a reason. Not just a ah ah if the nut vibrates lose kiss you vehicle good bye!!!!

@idiocracy5114 9 ай бұрын

How is the intermediate shaft holding up so far? Im about ready to tackle this one my 5th gen.

@DavesBuild 9 ай бұрын

So far so good!

@DavesBuild 9 ай бұрын

So far so good!

@brianlawrence9493 7 ай бұрын

Do you have the part numbers for the 5th gen? All I can find is the ones that fit the classic

@cmz85 10 ай бұрын

How many miles did you truck have to have to replace this already?

@DavesBuild 10 ай бұрын

I noticed it at about 150k I believe. Some have had issues at 50k...

@fonzb2890 Жыл бұрын

question, hope you get back to me. Can you tell me what part number that is?

@DavesBuild Жыл бұрын

Products links are in the description. Thanks for checking out the video!

@fonzb2890 Жыл бұрын

@@DavesBuild What did you use to take out the needle bearings?

@colebergman6118 Жыл бұрын

Did that shaft kit come with both or just the passenger side?

@DavesBuild Жыл бұрын

It comes with both sides.

@DavesBuild Жыл бұрын

There is also a link in the description.

@diamondranch44 Жыл бұрын

Thank you for the video. Did you get the intermediate shaft kit off eBay from the shop in Canada?

@DavesBuild Жыл бұрын

Ebay yes. There are other suppliers now. You can get the kits for about half of what they used to cost.

@chasegagnon9755 Жыл бұрын

Hi Dave any info who is best to Purchase this kit from thanks in advance big fella

@DavesBuild Жыл бұрын

@chasegagnon9755 at the moment I don't know the difference in the different suppliers. They may be all sourced from the same place. The kit I bought was around $250. I have a link in the description but not sure if they still supply them or not.

@chasegagnon9755 Жыл бұрын

My apologies I see it now Dave thanks a lot big guy cheers

@chasegagnon9755 Жыл бұрын

Also my new body has 6 bolt wheel bearings as classic models only have 5 wanted to verify if yours had 6 aswell?

@reckless3008 4 ай бұрын

Must be a common problem doing this on my 17 ram1500 soon

@ryanbruegger4522 Жыл бұрын

Did you have severe vibration before your alignment?

@DavesBuild Жыл бұрын

I did have vibration before changing it.

@shaunhallman4198 10 ай бұрын

Hi..did ur steering wheel shake before replacing parts..ive replaced so much qnd still shakes..i have a 2010 6 inch lift..new tires lots of new suspension partsdriver side stub shaft and new cv's

@RickySlatton Жыл бұрын

Dave, What symptoms were you having to alert you these were bad?

@DavesBuild Жыл бұрын

Slight vibration. Saw what looked like dried up rusty water around where the cv attaches.

@RickySlatton Жыл бұрын

@@DavesBuild thanks. Did you have vibration in the seats or steering wheel?

@DavesBuild Жыл бұрын

Seats mainly

@RickySlatton Жыл бұрын

@@DavesBuild cool. Thanks.

@Trucker939 Жыл бұрын

Where did the orings go ??

@benjaminkline4855 Жыл бұрын

At 35:50 he adds a c clip to the output shaft, a o-ring goes in the groove a inch below that. When you install cv shaft, the end of cv shaft will go 1/8 past the oring before before the c clip lock the 2 together. The oring keeps dirt and water from getting into the splines.

@WWood715 8 ай бұрын

Thank you so much. I've been trying to figure out o-ring location and purpose. Thanks for such a clear explanation. @@benjaminkline4855

@josesamaniego2505 Жыл бұрын

What are the symptoms that the truck presents for you to come to the conclusion that this was the problem, maybe it shakes when you accelerate, vibration or something similar, let me know thanks 🙂

@DavesBuild Жыл бұрын

I slight vibration at speed. Couldn't figure it out. Also looking under the truck there was rust stain in line with the axle and cv connection.

@demetrius1510 Жыл бұрын

How long did u put that bearing in the oven for

@DavesBuild Жыл бұрын

20 mins about 180 degrees, I believe .

@demetrius1510 Жыл бұрын

@@DavesBuild thank you I appreciate it I'm gunna try n do this today

@DavesBuild Жыл бұрын

Make sure you freeze the shaft also. I put mine in the freezer the day before.

@demetrius1510 Жыл бұрын

@@DavesBuild ya I put it in the freezer last night

@Jetta2MTL 4 ай бұрын

Do you need a press ? Other videos says you need a press

@DavesBuild 4 ай бұрын

I did not need a press. Heated bearing and froze shaft.

@Mike-sr6gd 3 ай бұрын

@@DavesBuildthat's how I rebuilt my whole rear end. No pulleys or presses.did it on my kitchen table lol

@matthewhegstrom8478 Жыл бұрын

How did you know that whole thing was bad?

@DavesBuild Жыл бұрын

With that much play in it, it's best to replace the stub axles also because the splines get worn down and damaged with the cv axles as well. Just changing the cv axles doesn't fix the issue it's just a bandaid.

@johnjlanejr Жыл бұрын

35mm or 36mm for axle nut?

@DavesBuild Жыл бұрын

35mm, new axles I installed were 36mm I believe.

@johnjlanejr Жыл бұрын

Well damn...I ordered a 36mm to do an axle change this weekend and I'm removing OEM...hope it fits!

@DavesBuild Жыл бұрын

Should work anyway. Just be a tad loose. Lol

@Ti-DAWGS 4 ай бұрын

I have a 2013 Ram. My front axles are messed up also. I see this as a huge design flaw. Some other trucks have a male splined shaft which inserts INTO the diff, not on top of the protruding male shaft coming OUT OF the diff. Water gets in! It destroys the axles AND the shafts in the diff. What a huge problem. There are other silly design features of my RAM which have caused problems. I'll be buying another manufacturer's cars in the future.

@Gatorman6924 Жыл бұрын

Be real helpful to post the year.

@DavesBuild Жыл бұрын

This is a 2014, but they are the same from, I believe 12-21. If you have this problem then this video will work for you.

@Gatorman6924 Жыл бұрын

Awesome thank you, I have the same year doing the same thing right now.. What size was the socket did you used to get that needle bearing out?

@josephdossantos9274 5 ай бұрын

You need to get the torque specs for the job you are doing. Get yourself a good torque wrench, and avoid using the power tool on the spindle nut because that will destroy the bearings. Always use a torque wrench. Good luck.

@garrettsmith6679 Жыл бұрын

Rams are funny. Can’t just remove the whole knuckle because the axle is in the way and won’t let the lower ball joint clear, and you can’t slide the axle out easily cause the lower ball joint is holding the knuckle on. Stupid. So what your suppose to do I think is pop both ball joints leave the bottom one attached but as loose as possible, and tilt the knuckle down and pop the axle off the stub shaft first, this way you don’t have to mangle the axle.

@WILSON.1 8 ай бұрын

Liberal: "Hey you can't be spraying brake cleaner like that letting it drip on the earth. That's an environmental violation. You need to contain all of it, drive it to a special waste facility (drinking gas to get there), and pay more money to dispose of it properly. By the way, after you finish yours, can you do mine? 100 bucks? What? Is that negotiable?"

@DavesBuild 8 ай бұрын

🤣

@rezkidgamingyt4725 3 ай бұрын

Lmfao

@presario4444 3 ай бұрын

How about investing in a tripod for your camera because watching your head mounted GoPro makes for a very crappy video.

@DavesBuild 3 ай бұрын

I do accept donations. 😆 I use what I have because I don't make money from these. Just trying to help. There are other videos out there that show how to do this. Thanks for stopping in.

@Gatorman6924 Жыл бұрын

How did you bust out them damn bearings they just keep spinning! Lol

@DavesBuild Жыл бұрын

The needle bearings?

@Gatorman6924 Жыл бұрын

Yea the needle bearing

@DavesBuild Жыл бұрын

I beat a screw driver or punch, can't remember, in it to to bust the actual bearings out. Then I wedged a socket on the inter lip and started beating. Just be careful to not break the lip completely off. Maybe a little heat outside the casing would help to. That was going to be my next option.

@Gatorman6924 Жыл бұрын

I was thinking a dermal and cut off wheel, to help it collapses on itself.. Trying to avoid that at all cost.. Thank you sir. Back to the garage.

@Gatorman6924 Жыл бұрын

So I ended up using the Jack handle of a harbor freight Jack and beat the corners, with the housing secured in my vise.. Came out pretty easy! Left the needles in!