2012 Chevy Malibu P0013 Exhaust Cam Sensor exhaust

No video

2012 Chevy Malibu P0013 Exhaust Cam Sensor exhaust

Рет қаралды 21,264

Күн бұрын

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#chevyp0013 #camshaftsensor #camsensor #chevymalibucamsensor #camsensor #exghustcamsensor #malibuexghustxcamsensor #chevyexghustsenst

Пікірлер: 55

@suhblu 28 күн бұрын

It's not typical for camshaft sensors to have oil on them. If you notice oil on or around your camshaft sensors, it could indicate a few potential issues: 1. **Oil Leaks:** - **Gasket or Seal Failure:** A common cause is a leaking valve cover gasket or camshaft seal. These components can allow oil to seep out and reach the camshaft sensors. 2. **Sensor Damage:** - **Contamination:** If oil is on the sensor, it could affect its operation or cause inaccurate readings. This can lead to performance issues. 3. **Engine Condition:** - **Excessive Oil:** If the engine is consuming or leaking oil excessively, it might also reach other parts like the sensors. **Actions to Take:** 1. **Inspect for Leaks:** Check the valve cover gasket and camshaft seals for signs of leakage. Replacing faulty gaskets or seals can prevent further oil contamination. 2. **Clean the Sensors:** Gently clean the oil off the sensors and check if they are functioning correctly. Ensure you use appropriate methods and materials to avoid damage. 3. **Check Engine Condition:** If you frequently find oil on the sensors, it might be a sign of a more significant issue with the engine or oil system. A mechanic can help diagnose and address underlying problems. Addressing the source of oil contamination is important to maintain the proper function of your camshaft sensors and overall engine performance.

@MsLovehate13 Жыл бұрын

Great video i changed the front cam sensor no prob. I cant get the exhaust one in the back back on because of the metal bar. Can the metal bar be moved ? Please help 🙏

@RBTheMechanic Жыл бұрын

Yes u have to remove it it’s tough one

@MsLovehate13 Жыл бұрын

Is there a video on how to remove the metal bar that is in the way of the bolt that holds the sensor. Or what is the name of the metal bar that's in the way

@RBTheMechanic Жыл бұрын

@@MsLovehate13 I don’t have video on it I know I did this but idk why I don’t have it on camera

@alexuriarte3 Жыл бұрын

Great video! Question: do I have to unplug the battery before I begin this fix ? Thanks in advance

@RBTheMechanic Жыл бұрын

No need to disconnect

@AustinLocksey Жыл бұрын

Getting code p0016 and 0017 I replaced the two cam solenoids and didn’t fix, assuming these are the next check?

@RBTheMechanic Жыл бұрын

Yeah knock out the sensors also

@djlivelee3325 9 күн бұрын

Dont you have to relearn the system after replacing these parts?

@RBTheMechanic 9 күн бұрын

No just need to reset

@aarontna1 11 ай бұрын

Are the intake and exhaust sensors the same?

@RBTheMechanic 11 ай бұрын

I think so but the angle of the bolt ear could be diffrent

@crazycarmal9792 11 ай бұрын

Do you have to re learn them or will the car do it by itself?

@RBTheMechanic 11 ай бұрын

Not required just replace and then reset the light

@crazycarmal9792 11 ай бұрын

@@RBTheMechanic ok sweet any tips then for cleaning the gunk out of the ports? I suspect that’s why my code is throwing bc it missed an oil change and I assume it probably would cause the new ones to not read properly as well?

@crazycarmal9792 11 ай бұрын

@@RBTheMechanic I am also just swapping both sensors as well by the way

@RBTheMechanic 11 ай бұрын

@@crazycarmal9792 doing both is best so they not giving equal strong siginals

@RBTheMechanic 11 ай бұрын

@@crazycarmal9792 not sure about cleaning try using screwdriver and rag

@alyssavillanueva9452 2 ай бұрын

Is there only 1 intake and 1 exhaust camshaft sensor or is there 2 intake and 2 exhaust

@RBTheMechanic 2 ай бұрын

Yes 1 and 1

@Speakerboxers Жыл бұрын

Is it possible to just clean the sensor off?

@RBTheMechanic Жыл бұрын

No replace it

@Speakerboxers Жыл бұрын

@@RBTheMechanic I just tried…long story short I just ordered the part off Amazon 😂 & I’m gonna do a engine flush while I’m at it

@stephanie8327 6 ай бұрын

Is deoxit D5 ok to use to clean the connectors?

@RBTheMechanic 6 ай бұрын

Not sure they have electrical connector spray

@stephanie8327 6 ай бұрын

Just did this on my 2011 Malibu and it was a b*tch to get to. Had to remove multiple other parts to get my wrenches in there. 3 hours later I got it done!

@RBTheMechanic 6 ай бұрын

Yeah Chevy and ford made it difficult

@stephanie8327 6 ай бұрын

@@RBTheMechanic you said it! At first I thought it was just bad engineering but then I discovered you have to remove the ENTIRE FRONT END to change the headlight bulbs ….. total set up!

@juandelgado2525 Жыл бұрын

👍👌

@Menice1153 2 ай бұрын

Theres two sensors right?

@RBTheMechanic 2 ай бұрын

Yes

@brandanluc8106 Жыл бұрын

Anyone else having an issue with changing the cam shaft sensor, then the car not wanting to start. But it starts with the connector disconnected.

@RBTheMechanic Жыл бұрын

Not me

@alexloeragallos Жыл бұрын

I changed the sensor now it wont start

@RBTheMechanic Жыл бұрын

@@alexloeragallos check ur work and scan the car for codes could be faulty sensor I had similar issue on kia new sensor was bad car didn’t start