I literally had this problem today. My wife called me in a panic stuck in the road in traffic. I instructed her to shut off and put in gear and try to get the car off the roadway. She did and she waited for me to go pick her up. I searched out this issue and got to your video. Did exactly what you instructed and it worked. The valve wasn't all the way opening. Cleaned it with the cleaner (not exactly the same can but one that was a good substitute) worked like a charm. Thank you. Thank you. Got better acceleration and just runs better just from that. Thanks again amigo!!

You genius! We took my mom's car to a mechanic that told us it was going to be the spark plugs and coils and wanted us to spend 1500 to replace the parts. I saw your video and gave it a shot. It's running better than before now so thank you for making this video.

Thank you for this man! My Camry used to want to stall in stop lights and now it idles pretty comfortably without vibration.

Great job pm explaining the detachment of every connector. I've been a boiler operator/mechanic, a rocket surgeon, and now I'm on my last gig before I retire doing logistics for a chip maker. I know how to follow instructions. But far too many of these videos leave out or gloss over a critical step. I don't know why- if you doing a How-to, it completeness that matters - not the background music or cool intro. I'm just watching this for like the third or fourth time, right before I pull that assembly so I don't end up with a mystery connector, or spend an extra half hous because I disconnected the wrong side of something, and irmt just struck me how well you covered the one indispensable sequence clearly and succinctly Kudos! Update Wouldn't you know it, just as I got to thr last clamp, the rain ppen up and the wind kicked up. Ducked.back in the house to warm up and dry out.

THANK YOU! A friend of mine *just* got his Camery back from an (albeit unrelated) expensive mechanic visit and a day later it started to stall when idling. As a result, he's already a couple grand in the hole and this was not what he needed to deal with a day later so I looked into it, found your video, and within 15 minutes his car's running great again!

Wow this was a super simple procedure and worked great on my 2011 Carolla with 186k miles! The engine seems to run much smoother and idles at a higher RPM (around 1000). Thank you 👍🏻

M Camry 2001 had this issue too. Cost was $115 for a cleaning. Thanks for the video. It helps me understand what the mechanic did.

Man I watched so many stupid videos about messing with the wiring harness and vaccum lines to resolve this issue, this actually solved my cars issue and saved me so much headache and money 🎉

Broooooo you are a lifesaver lol. Swapped my battery didn't know about the idle reset until I googled why my idle sucks after changing my battery and bam got it solved thanks to you in 5min. FJ runs like a champ now

You saved my life I don't know how to thank you enough. God bless you!

Thank you for this video . I have a 2011 Camry that was doing this . I changed the MAF and nothing . I followed your steps I. This video and it fixed the car . Thank you again

Thanks for the video man. Saved me tons of time and money. Late night fix so I can get to work tomorrow 🤙🏽

Thank you for this video. My hubby bought ignition coils & spark plugs & it didn’t help the stalling so we’ll try this next.

Thanks for the video. It was helpful for me. That hose clamp was not easy to get to😄. It’s running better now, no stalling.

Thank you, sir! My 2011 Toyota Camry is running and not stalling anymore.

Nice video! I had to show this to the mechanic!!! Cause they didn’t know what To do and couldn’t know why my car was shaking and shutting off, I just needed to get this cleaned.. thank you!!!

Thank you I just did this ten minutes ago… my idle is above 1500.. I think it’s kinda high but maybe because it’s still cold.. regardless before my idle was 500 and my car would shut off randomly on idle .. thanks so much I liked and subscribed

Thanks. I had the low rpm issue(down to 500 rmp) especially when turning on the ac. after the cleaning it the low idle is gone and engine is smooth 800- 900 rpm.

Going to do this tomorrow; my 2010 Camry just started stalling when I stop. I changed the plugs and air filter- both needed to be replaced, but it’s still stalling. Thanks

Thank you sir. Had to disconnect battery earlier. It was stalling bad. This fixed it

Great how to. I like it bc you go straight to the point. Is it harmful to the tb if i spray into the flappy thing?

Good video, if you have no one to help you, just disconnect the battery, and do the rest on your own, no check engine light no codes, no harm done as long as the battery is disconnected, i did that on my, camry, my corolla, with no problems at all, the computer will reset and rpm will get back to normal after a couple of hours of driving.

You explained it perfect. Great video. It worked for me. You saved me a lot of money Thanks a lot.

Thanks, I think a have a bad pcv that is causing this problem, no smoke but I burn a quart every 2 weeks.

I did clean it on my 2014 scion xb and it didnt work, so I went and bought a used one and its good now. I guess my problem was in the Electric sensor.

can you just place a brick or something heavy on the accelerator while doing the entire cleaning process (instead of having a second person)?

Use a toothbrush instead of a rag. Makes it a lot easier and cleans those hard to get to spots

Hi 👋🏿 thank you for posting this is an extremely helpful video. Do these cars have a idle air control valve, or just the throttle body?

Hi there, I have a 2010 Camry which is stalling when I put it on park or neutral. This only started happening after I changed my battery. Do you know what might be the issue and how to fix it ?

Thank you

Thank you, easy to follow instructions. Very useful

Nice explanation. I have a problem with 2017 camry. It used to vibrate (as if driving on rumbler) when the rpm is around 1500. It runs smooth above and below that rpm. The mechanic diagnosed and replaced the front axle but it only made the situation worse. It occurs more frequently now and intensity of vibration is increased. Do you have any suggestions?

definitely appreciate this video ! everything worked just like you explained!

Well, I cleaned the throttle body by following the instructions in this video. Now I ser a check engine light. Any ideas? Car :2013 Toyota camry LE

Thanks so much for the details description of the process. I got a new battery and new alternator but problem didn’t get fix. After this process, no more crazy idle and most important the engine doesn’t shut down at the red light. 🫡🙏🏼

Thanks for the video my car works great now 👍🏽

I cleaned my Subaru throttle in exactly the same way. Had to disconnect the battery to stabilize the rpms after that.

Hello! Please help, i performed the throttle body clean as you instructedon my Camry 2008, but now the car jerks when idle, especially when the car is in Drive and i have the brake pedal pressed. I've trid idle relearn procedure but no luck, any suggestions? I notice the RPM gauge is jittery and spikes up slightly. Car drives fine, but that jerking & shaking when idle is not normal, please help.

Good video. Very well explained and worked.

It worked !!! Thank you so much !

After I cleaned mine, check engine is now on. Is that normal?

Great information brother… I will try this on my Toyota 2014 … my car feels like it wants to shut off wile driving like I can see the RPMS drop . Any good ideas?

Here for lil bro’s Scion - buh yes MY Pontiac Grand Prix was KNOOOWWN for this super small detail 😫

And remove the hoses very gently as they get hard with heat and can get damage if pulled hardly

Show the relearn process and cleaning MAF sensor. I had to do this recently 2011 Camry

When the engine is warm and if I let the car sit for 10 minutes and restart the car, the idle drops to 500 rpm for 1-2 seconds, runs rough, and then the idle smooths out? Any idea what could be causing this issue? I cleaned the MAF sensor, throttle body, replaced the plugs, coils, ECT sensor and crankshaft position sensor, and it still does this. There is no CEL, crank time is short and no noticeable drop in gas mileage.

Thank you so much, God bless you alot😊

I cleaned and it’s still not working Could I just change the throttle body sensor on it? or do I have to replace the whole throttle body ?

Hello dear I have Toyota Camry when I start engine shake please suggest me

To clear the check engine light you just plug in an obd2 sensor?

I just did that and my cars check engine is on right now, also when i turn the car on the rpm is almost 2000, what would be the reason?

i just did what you do... now the engine idle at 1600rpm, what should i do? i saw your reply about idle re learn. how do i do that? is there a video on that?

Hi sir I have 2010 Toyota Camry 2.5 l is jerk when I drive and then it goes.qwqy when I speed? Please I need your help

What about v6 2grfe misfire goes away when start and stop but comes on after a load

Thank youuuuuuu you helped fix my vehicle ❤❤❤❤❤❤😊😊😊😊😊😊

My vibe 2.4L gives a sluggish acceleration while on the slope.. could it be this?

I did it, it isn't stalling anymore, but now my idle is high like 2k and I am getting code for "Air temperature sensor" PO113 and "Volume air flow sensor" PO102

@RB the mechanic. I notice a misfire at 1300 rpm with engine cold or hot. It idles good and smooth and drives good. Sometimes intermittently I’ll come to a stop light and the rpm’s will drop from 900 to 600 and returns to 900 as if it was almost going to stall. Any advice?

Friends 2013 Rav 4 experienced similar issue. I cleaned maf sensor, changed battery. Keeps shutting off. Friend brings to Toyota mechanic and says its the throttle body so he cleans it. Week later, car keeps shutting off again at red light or stop sign. It’s not the throttle body! Brings Rav 4 back to me and I was going to pull spark plugs. Instead I check oil level. I checked the dipstick; there was no oil at all on the dipstick. I’m scratching my head. I ask: where do you get your oil changed at? Friend says Toyota dealership. I ended up having to fill with 3 quarts oil and immediately car idled better and rattle at startup went away. Took for test drive, car drove great and didn’t shut off. Simple but important fix: Folks, Check your oil level regularly especially after an oil change to make sure they put in the right amount. Go to a trustworthy place that will take care of your car properly if you can’t or don’t work on your own vehicle. I’m thinking either incompetent mechanic or intentional sabotage! 3 quarts short? Hmm. Makes me wonder! This mechanic is good though, I like the way he walks you through the repair. Good video and explanations paired nicely!

Hey. Thank you for the video. Today my 2013 Camry SE was running and while it was running I unplugged the AMS and the car shut off. I put it plugged the MAS back and turned the car on it turned on but the engine light turned on. How to reset the engine light off. Any help would be appreciated. Thank you.

Where can i buy the y tool screwdriver from? Is that the correct name of the tool? Thx

Solved my rough idling issue! Thanks so much!

I just did this today, I am in automatic technical class. Same issue 😂

My car idles poorly on drive and reverse gear with my foot on brakes, I feel vibration on my steery and dashboard while idling. It idles at 600rpm to 550rpm is this normal, with so much vibration n gets worse when I turn the ac on still on drive or reverse gear but reduces a bit when I put my car on park gear n vibration disappears when my car is moving n comes back when I come to a stoplight. I think, ama give this a try and see if it solves d issue.

Are you in New York? I have this same issue my guy literally 😂

Car nit said it's dangerous to step on the gear while cleaning. Just gently clean it.

My 2015 camry le idles at 800 rmps when it's on park but when I put on drive or reverse it drops to 500 or 600 rpms and it shakes and the has turned off when I'm at a stop sign or red light.

I have 2010 toyota corolla. similar throttle body top right cornar there is a screw hidden in a glue type material. can you please tell me, what is the function of that. and how it help in adjusting a specific parameter? I have observed that changing the position of that screw make throttal pedal to respond differently and effect the drivability . I have an issue of poor idling. throttle body is cleaned. every possibility has been checked but could not fix the issue.

Hi, may I have auto body shop address? I have same issue.

Hey can I use carb and choke cleaner?????

hopefully this all i need to do lol, thanks for the video

Hello, thanks for the info. Now I have to find someone to do it. Where are you located?

Check catalytic converter?

Hi there! My Toyota Camry 2014 has 75,475 miles on it and it barley started doing this. I noticed it doing it after I’ve been driving for a little and then stop at a red light or stop sign. It does it for a quick maybe 2 to 5 seconds where I see the needle want to go down and the car shakes and wants to turn off so I let go of the brake…..then it doesn’t do it anymore. Also, there’s no check engine light or anything. Can this be the problem?

Why is my car shutting off stalling hard once turned on? Toyota Camry 197xxx

good vid, thanks....btw you have a tank battery in that thing? haha

Followed directions now the idle is 1600 (2k with AC on) Suggestions?

I did it works perfect ,just getting the check engine light now ,what can I do?

The vibration only happens when ever i turn on the AC

For me the car never stalls but my idle goes below 500 and vibrates sometimes when stopping and braking. Any suggestions.

Great video and explanation

Hey, how much you think is a fair price to get this service done professionally?

Be careful with your fingers. After i do the fix as show in the video i read on reddit that if your finger its in the way and the throttle close it can slide the finger with no problem 😅🙆🏻‍♂️ thanks god i read that after i finish doing the work 🤣🤣

Can we clean it by removing totally ?

Do these cars have an IAC valve or is it part of the throttle body?

Man I went to this guy , he took that whole part out & I see why my car acting funny now ..when I press gas .. car add too much pressure by itself & more weight things .. help me please

Does this work on 07 Camry 4 cyl ?

I have toyota camry 2004 (manual) When i run the car without airconditon the rpm is not drop but when i turn on the Aircondition car feel little bit shake then car when running about avobe 30+ speed the rpm is good but when car get reduced speed car shaking and when gear in neutral engine get stop plz tell me about the problem🙏🙏

Any reason why a 2019 Toyota Yaris would be doing this? At 20,000 miles

Hello, nice job, cuestion, a dirty throtle can gives a po172 code?

Would this work for random reving up of rpm when driving? I noticed sometimes just driving a constant speed or sometimes when accelerating, it will rev up rpm then go down to what it normally increase to

What OBD scan tool do you recommend?

Excellent walkthrough, thanks! With the key on ACC, when you press the gas pedal, would that cause the computer to try to add gas as well to match the throttle body position? Can you leave the gas all the way down as long as you want with no issues?

Were those microfiber towels or just the blue shop tissues?

Good looks just got a rav4 it needs that

Man I having the exact same issue with my 2014 Camry and I changed the trotte body and it’s till turning off with no codes

Can I use brake cleaner for this?

thank you, sir

Do you happen to know what the problem can be when you depress the gas pedal with the key on acc the throttle flap opens really slow? At times It opens instantly then sometimes it opens slow?

How much do you charge for a throttle body cleaning?