Rear Wheel Bearing Replacement on Mazda 3 and Mazda 5 2004-2013

No video

Rear Wheel Bearing Replacement on Mazda 3 and Mazda 5 2004-2013

Рет қаралды 36,860

Күн бұрын

Fast and easy way to replace rear wheel hub bearing on Mazda 3 and Mazda 5 2004-2013 with or without ABS brakes.
❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video.
📎Other Mazda repairs
Rear Shocks Replacement on Mazda 3 and Mazda 5 2004-2013
• Rear Shocks Replacemen...
Thermostat replacement on 2010-13 Mazda 3 /Ford 2.0 engine
• Thermostat replacement...
How to align valve timing on 2010- 2013 Mazda 3 / Ford 2.0 engine
• How to align valve tim...
💰Save money on your car/truck maintenance and repairs:
Don't let Timing Belt Failure Happen
• Don't let Timing Belt ...
Learn 3 Symptoms of Blown Head Gasket
• Learn 3 Symptoms of Bl...
Look what happens when you neglect your engine oil
• Check and Change Your ...
Always make sure your lug nuts are TORQUED and not done with an impact gun
• Don't Use This When Ch...
How to diagnose and replace wheel bearing going bad on any car
• Whining, Grinding Nois...
Learn why the tire pressure is important and how to check it in your car
/ bm8wnjripj
Check your Engine, Coolant, Transmission, Power Steering Fluid, and Brake Fluids
• Check Your Car Fluid L...
Remove and replace Broken or Stripped Wheel Stud on most cars
• Broken or Stripped Whe...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

Пікірлер: 60

@petermiller8634 Жыл бұрын

Excellent tutorial with good verbal descriptions during the operation 👍👍

@Motorcarnut Жыл бұрын

Thank you, appreciate the feedback!

@jeffersonfreed2716 7 ай бұрын

Thanks for this video. I just did this job today on my 2010 Mazda 3 S. Mine has ABS, and the ABS sensor was attached with a odd little star shaped bolt, probably E-torx, but I'm not super familiar with those. I was able to easy remove it with a regular 5mm combination wrench. Also, on my car, the bearing hub assembly was held together with a regular socket bolt, so I didn't even need the big Torx bits you used. And yes, it's possible to remove the entire brake caliper/bracket if you want to save time and you're planning to re-use your same brakes. Just be prepared to use a beefy 14mm combo wrench, because on my model, a brake line runs right over the one bolt, prohibiting a standard socket wrench. Thanks again for the help!

@Motorcarnut 7 ай бұрын

Thank you as well for the great extra info!!!

@fubarace1027 2 ай бұрын

Thank you for the detailed video, going to do the job next weekend I think on an 09 mazda3. I'll let ya'll know if I hit any snags.

@Motorcarnut 2 ай бұрын

No problem! And good luck

@jmspeedmedia Жыл бұрын

Easy. Good video man. I need to do my rear-end now. I just did my front end, that was more complicated. I didn't remove the brake pads just remove the whole caliper and brackets lol:) and slide everything back on.

@Motorcarnut Жыл бұрын

Great and thank you for sharing and the comment

@andrewadams9819 11 ай бұрын

Indeed more complicated lmao

@terminalfx Жыл бұрын

Good note on the offset holes when mating it with the dust shield. Came across this vid to make sure I wasn't going crazy 🤣

@Motorcarnut Жыл бұрын

Lol, no problem

@homestylegravy Ай бұрын

If you have ABS brakes and get the wheel hub from AutoZone, it doesn't come with the ABS sensor. You have to take the sensor off the old hub and screw it onto the new one. It has a weird inverse torque head (E5 I think), but I got it with a 6 mm socket.

@Motorcarnut Ай бұрын

Most come with the abs sensors and if vehicle doesn’t have it, it can still be used. Didn’t know about AutoZone thanks for that extra information maybe can help others!

@ginsadventures1747 6 ай бұрын

Thank you very much for this video. Helped me so much

@Motorcarnut 5 ай бұрын

Glad to hear it! Thank you for the feedback!

@Toaster_Tier5 2 жыл бұрын

great video thank you!

@Motorcarnut 2 жыл бұрын

Thanks for the reply

@rafaellara4122 Жыл бұрын

Thanks for the video bud

@Motorcarnut Жыл бұрын

No problem

@AlanJOrtiz Жыл бұрын

Thank you for this video

@Motorcarnut Жыл бұрын

You're welcome, thanks for the comment.

@MLef111 2 жыл бұрын

Great video, thx. How much foot pound do you torque the wheel bearing hub ?

@Motorcarnut 2 жыл бұрын

48 ft lbs

@ryantalaue Ай бұрын

Sir i have a mazda 3 2008 2.0 i need to replace the rear axle bearing. after replacing it do i nid to do wheel alignment?. thanks!

@Motorcarnut Ай бұрын

@xXNightsWatchXx Жыл бұрын

Only comment would be you can just pull the entire caliper off with 2 bolts and then slide it out

@Motorcarnut Жыл бұрын

True, but it’s a little bulkier that way, but yes.

@ryantalaue Ай бұрын

is that a hub type bearing just new car owner.. thnks

@Motorcarnut Ай бұрын

Yes

@trentsawatzky2928 10 ай бұрын

Are the rear hub assemblies left and right oriented, or are they universal fit for left and right

@Motorcarnut 10 ай бұрын

Universal, the only thing you have to make sure of is if you have ABS or not.

@ANT3L 2 жыл бұрын

What is the brake dust bolt size? Don’t now anything about bolt sizes, getting my Wheel bearing and brake dust changed tomorrow….what bolt size should I buy?

@Motorcarnut 2 жыл бұрын

What do you mean brake dust boot? The calliper bolts? If so there a torx T45

@rekazu Жыл бұрын

What’d you do to get the piston on the brake caliper to come back out? Just pump the brakes like normal and it unscrews itself?

@jorgecazares1219 Жыл бұрын

What's the torque spec?

@Motorcarnut Жыл бұрын

The rear hub assembly is 50 ft lbs

@danilke8439 9 ай бұрын

I have a 2010 mazda 5 , should i order wheel bearings with ABS sensor or without ?

@Motorcarnut 9 ай бұрын

If your vehicle has ABS then you have to order one with it, if yours doesn't have ABS then either one is fine.

@robobunch4212 Жыл бұрын

I noticed the new hub has the abs port. Does it matter? I ask bc I just bought a hub yesterday and the non-abs was $20 more.

@Motorcarnut Жыл бұрын

No, as long as your car doesn’t have abs

@mindiseverything5036 2 жыл бұрын

The fronts are not assemblies like this right? It's like a press bearing style

@Motorcarnut 2 жыл бұрын

Correct

@christinelabrie1430 Жыл бұрын

The 4 bolts T50 are stuck, any suggestions to get them off??

@Motorcarnut Жыл бұрын

Heat, but be careful

@autograph415 6 ай бұрын

is this similar fora cx-5

@Motorcarnut 6 ай бұрын

Should be

@autograph415 6 ай бұрын

@@Motorcarnut I've got a question mlt sure if you can help or not, so my mazda cx5 i think is a wheel bearing but not entirely sure, it sounds more like a whistling on the passenger side more then a growling, could that still be a bearing

@Motorcarnut 6 ай бұрын

Yes

@gurs5804 Жыл бұрын

Where can I find the torque specifications for mazda 5 2010, I cant find them anywhere? The ones I find are says 170 foot pound And my wrench is inch pound with a range max 960. If I convert 170 ft pound to inch pound its around 2000 inch pound ? Also I want to know the torque on T50 screws for wheel hub assembly Brake bracket Capilar pins Lugnuts. Where will I find them ?

@Motorcarnut Жыл бұрын

Alldata diy online $20 a month or your local library online Free should have decent repair info as well. I'm not local now or I would send them.