www.TiredIronVideos.com/ Learn to press apart & repair a John Deere diesel water pump and pulley. Save money by rebuilding your water pump instead of replacing it.
Пікірлер: 59
@patkelly16213 жыл бұрын
so refreshing to see old school repair rather then just replace
@paulvaultguy5 жыл бұрын
One of the best instruction videos I have seen.
@jeffsenffner92347 жыл бұрын
Thank you, really appreciate you taking time to make this video. Feel better knowing how it is supposed to come off and go back to gather.
@RutherfordGeorge12 жыл бұрын
Thanks a lot - a really helpful video and very well done. I am just rebuilding my tractor water pump and your video is perfectly on target!! George Rutherford in New Zealand
@donshotrodgarage17176 күн бұрын
Video Good video. I enjoyed watching the process. Thank you
@soldador17756 жыл бұрын
thanks for your patience many countries of south, america do not manufacture spare parts for vehicles, so we have to repair, thank you for your videos ..
@rbenitez135211 жыл бұрын
Man, it is great to know how to do this. My water pump on my car just went bad. It costs about 189.00 dlls. This could definitely save me some money. Thank You very much for this video.
@jimbuford41477 жыл бұрын
I have your video series and they are great. You do the best job I have seen in explaining what you are doing that I have seen. If you would really get into various repairs on different makes of tractors you would have a tremendous following.
@bricgibbs17369 жыл бұрын
Great video and thanks for taking the time & sharing.
@hotpuppy725 жыл бұрын
Thank you for a good video that explains how to actually rebuild a water pump. Many other YT videos are fluffed with nonsense about what a pump is or how coolant works. :)
@dkdj52 жыл бұрын
Thanks for the info. I knew all that. I just need to know how to get the pulley off without breaking it.
@tonylangley26103 жыл бұрын
Great Job on this video, as you do on all of your videos !
@jimrankin2583 Жыл бұрын
If the impeller or pulley flange of your pump has pulling holes, best plan is to pull them first. Sometimes there’s something hidden behind the pulley that’s important to know before you break the housing! Most water pump housings aren’t all that strong. when you get to pressing and the impeller is stuck, you can crack the housing. Sometimes you have to do it that way, but it’s best to pull impeller if there’s a provision to do it.
@thomascatford26276 жыл бұрын
First class video a man that really knows his job
@DIXIEMAFIA251 Жыл бұрын
Awesome video Brother! About to do this on my 96 Chevy K1500..Been 12 years since this video,I hope all is well!
@Redlinesixtynine10 жыл бұрын
Very informative vid. Thanks!
@RicardoMartinez-ug4vv8 жыл бұрын
Cool video, really informative. i think people should overhaul water pumps more often. what would you commend I use to remove a pulley hub for a spin on clutch.
@oby-16076 жыл бұрын
Man. I gotta rebuild my water pump on my excavator John Deere. Sure glad I found this. Thanks.
@MadKingChristopher7 жыл бұрын
Thank you, sir! You have helped us immensely!
@mmolloy49616 жыл бұрын
Nice work there
@MikesBetter12 жыл бұрын
Great video! I work on lots of old obsolete stuff. Usually the housing and impellor is fine and all I need to do is replace the bearings and seal. Who is a good supllier of bearings and seals? I'd like to order by dimentions if possible
@jairoavila49444 жыл бұрын
Thank you for the video👍🏽
@williamconfer97847 жыл бұрын
Great video
@joecorrie111 жыл бұрын
great video, thanks
@donfreud2126 жыл бұрын
Nice job. Where can I order seals for my water pump (2004 chevy silverado, 6.0 L. gas engine)?
@ruffneck70263 жыл бұрын
This is a great vid, but your particular seal style does not contact the impeller shaft as you indicate with a clearance fit, however there are ones that are an interference fit on the shaft and need to be pressed on. The pressed bushing of the seal will turn with the shaft in that design. You should have mentioned the press fit design as well in the video to avoid confusion to the assembler when they go to "slip" the seal over the shaft and it interferes.
@CJM176277 жыл бұрын
I have a John Deere 1050 tractor it overheated. It was the first time it is overheated that I know of. I just checked the thermostat and it opened in boiling water. So here's my question. It has a direct fan yamar three cylinder Diesel engine. If I spin the fan fast enough with the top radiator hose off (and the thermostat out) would I be able to identify if the pump is working by the water sucking or shooting out of the top?
@TheTileplace2 жыл бұрын
thank you great video awesome explanation thank you
@jamescopeland53582 жыл бұрын
Great video, thx My pump shaft broke. What's the best way to get the outer race out?
@donfreud2124 жыл бұрын
What's a good online source for kits (bearing and seals) for auto water pumps?
@RRaucina8 жыл бұрын
Great information. Is that a JD RE41897 excavator water pump?
@davidgriffin1411 жыл бұрын
wow, i actually learned something on youtube!
@woolyhighlander7280 Жыл бұрын
Good Video ,thanks
@Murphy363710 жыл бұрын
Not all bearings get pressed out the pulley side. I did it your way, inside to outside, and the Impeller broke. The pump is an F2244R. On this one, once the pulley is removed, and the hairpin keeper removed, I press the bearing to the inside, and then block the impeller and press the shaft out.
@Dan-ue1gr9 жыл бұрын
How about showing the pulley removal? that IS part of the process!
@1973ante4 жыл бұрын
Where to find bearing and seli kit for waterpump mopar 383, 1967?
@pubsauthor7 жыл бұрын
Great video. Should help me in rebuilding a Chevrolet truck pump.
@Hot80s10 жыл бұрын
my car has a special water pump that costs over 400$ I found the same pump but not the same cast, the internals are identical, can I simply press the 68$ rebuilt pump's internals out & install them in my old pump?
@canoworms275 жыл бұрын
this guy is good...
@fair2middlin2 жыл бұрын
I missed out on the gasket installation and rebolting
@thinktwicez716 жыл бұрын
what is the type of sealant you used for the seal ? who makes it and what is it ? thanks
@123ABC-Machine-Basics2 жыл бұрын
That is the Permatex Aviation 3D sealer
@starzanhorse47582 жыл бұрын
My Mercedes’ pulley is sticking out 1/4 inch. Can I just smack it back In?
@nohyphens6 жыл бұрын
Found this video after I rebuilt my JD pump. I did not put any sealant on the seal housing, now I am worried. I hope it still works........blah.
@travisgregory64429 жыл бұрын
im gonna be doing this job next weekend does anyone know if you have to pull radiator or can waterpump be removed with radiator still in place thanks
@rgnichols5673 жыл бұрын
I have an old 5020, & I didn't have to pull the rad. Its tight, but was able to get it out without damaging the rad.
@andiabdillah13024 жыл бұрын
Nice info I'm mechanic auto Can u change water pump move not from crankshaft but into turbines using turbocharger it will increase enggine power also reduce enggine baggages.. and oil pump also Re.. Andy
@CrazyHHO1910 жыл бұрын
waw that was a good info
@rgnichols5673 жыл бұрын
Just wondering how you got the pulley off of the shift? Mine is frozen on pretty solid, might have to get the torch out on this one
@HarveyHamilton3 жыл бұрын
With a bar type puller.
@lindarahim-zl2ki Жыл бұрын
Can you tell me what this sealant is that you are using on the seal. And also who makes the sealant.
@harveyhamilton9997 Жыл бұрын
The Right Stuff by permatex
@tedpeterson11566 жыл бұрын
Wrist pin off of what?? lol Nice video
@TiredIronVideos12 жыл бұрын
I do not order by dimension so I don't have supplier. OEM suppliers many times have kits or aftermarket kits are sometimes available. tiredirontractorparts . com
@jasonerb25774 жыл бұрын
You must be a fellow Pennsylvanian...I heard a "warsher" in there.
@coffeefish4 жыл бұрын
The was all pump and no pulley. I want my money back.
@markdoiel80392 жыл бұрын
but you started after the pulley was of and skipped over pressing the shaft out of the impeller those are the are the things people need help with without it the video is worthless.