Great explanation. I just installed carburetor at my Honda power washer GX 200 6.5 following your instructions. It was very helpful. I have to get a gas and will tell you how it goes. Thanks, Jasbir Mongia
@JosephFrylingАй бұрын
thank you! someone just gave me one of these pressure washers. trying to start a side hustle. hopefully this gets it working again.
@markshuput5228 Жыл бұрын
I put a new Honda OEM carb on my gx 200. It would start but not stay running. I watched your video and the manifold gasket, I put on backwards. Hole twords the valve cover. I reversed it and it runs like a scalded ass cat. You saved the day. Thanks 😊
@bobtummino3521 Жыл бұрын
Video was very helpful to be sure the procedure to remove and replace the carb properly including installing the governor linkage and gaskets. You can use the male part of the plastic choke to plug the fuel line while working on the carb. In my case the fuel tank needed to be replaced due to hard varnish and rust.
@harleythomas701Ай бұрын
Thanks for the video Currently trying to get an old pump to run with a 120 engine attached that my neighbour was just going to throw away
@GeneL562 ай бұрын
Golf ball tee to plug the fuel line. Great video, Thanks !
@HipaParts2 жыл бұрын
Thanks for sharing that. It's a detailed and helpful video with helpful tips.
@the1stime4 ай бұрын
Super helpful, thanks for doing this!
@Boomhauer692 жыл бұрын
Definitely was helpful video as someone who doesn't know anything about small engine or any engine for that matter. Definitely was good video. I myself thought About using a wood pallet sometime goof around and turn one into a go kart basically making a wooden go kart.
@jessejinkins83903 ай бұрын
I took the gas tank completely off. There was a cheap wire hose clamp that I just twisted off with a pair of pliers because I'm replacing it with a better hose clamp anyway and the damn thing actually sparked when I broke it off. Nothing ignited but damn.
@kevinmcmanus7298Ай бұрын
Super helpful video. Appreciate it.
@adamhix3882 Жыл бұрын
Very well done.
@jimpann Жыл бұрын
Great job
@TerryBilka-fq4ow3 ай бұрын
If you use the choke lever round rod to plug the gas
@PS4PROGAMER5456 Жыл бұрын
There is a niple on the choke lever and it will fit in the fuel line
@jacobellison35902 жыл бұрын
Can you show me how to build my own racing mower
@simon.scurtu Жыл бұрын
So do the Honda GX200 and GX160 have the exact same carburator?
@AlexJohnston-mu8ri3 ай бұрын
I installed the carb, but if I open the choke at all it revs up a ton. What am I doing wrong?
@dudebud728 ай бұрын
Just did this on a 140. I ordered a carb from Honda and replaced everything around it.
@specialt97442 жыл бұрын
You know the air box will still go on and off if you fully close the choke and turn off the gas right? And also you can reuse the gaskets if they aren’t ripped to shreds.
@Fucknuts4u10 ай бұрын
wow thanks for that time saving tip...
@rawbsworld66042 жыл бұрын
😂 tells everyone first thing you want to do is drain the gas, yet literally holds his finger over the gas line for the entire swap 🤷♂️ 🤦do as I say not as I do? That engine is a keeper , cleans off a saw table work bench real good! 👍😆 … ✌️🤙
@johnmichaud84792 ай бұрын
Clamp fuel line
@NotMeeither2 жыл бұрын
You forgot 1 thing, you did not put the hoseclamp back on the fuel hose.