Very Nice Thanks! I was thinking a spring controlled the tone arm had no idea it was damping fluid! Easy Fix👍👍
@johnabalos14552 жыл бұрын
This same injection method worked for me also,it’s easier to fill with fluid from the top directly into the shaft an work it in raising it up an down until you start noticing some results,have patience ,after sitting overnight it works even better!!!
@TrueAudio11 ай бұрын
gravity
@stephen5792 жыл бұрын
I hope mine goes as easy as that. Thanks
@drinkstonight2 жыл бұрын
any videos on an equal but opposite problem? my armrest doesn't drop when lever is depressed?!! thanks
@ricmusiclouis Жыл бұрын
Get your hand out the way!
@newsview7844 Жыл бұрын
Is this applicable to tonearms with P-mount cartridges (specifically a JVC AL-A155TNX, equipped with a 3kg "statically balanced, straight tubular arm")?
@arrya53722 жыл бұрын
Thanks for taking the time to post this. I have the very same model with the same issue. What was the viscosity of the oil that you used? Thank you.
@steved11292 жыл бұрын
On this particular turntable I used the 300,000 cst
@mrkrinkle8323 Жыл бұрын
I just bought 300,000 and was a bit worried so I'm happy to see this. Online one guy says 3,000cst and another says 500,000 & everything in between!
@abbierose89342 жыл бұрын
Hi.. where exactly are you putting the fluid? Inside the piston, or around the piston like you did with the Q tip?
@steved1129 Жыл бұрын
On this model I placed the fluid around the piston, but some turntables require removal of the shaft, which have a reservoir to hold the fluid.
@stonerider3427 Жыл бұрын
Your left hand is covering up what you are trying to fix
@AnasSyriano Жыл бұрын
What is the fluid please!
@ilventodellest Жыл бұрын
i have opposit problem, the Tonearm don't drop. i push down the arm but nothig happen.
@steved1129 Жыл бұрын
The grease inside may have hardened. You can try placing a little light weight oil (like sewing machine oil) on the shaft to loosen it up
@MusicBoxVinyl Жыл бұрын
Is that an empire cartridge?
@steved1129 Жыл бұрын
Yup. I think it was an LTD200 or 500.
@elizabethagnello7812 жыл бұрын
Not a good angle! Can’t see where you’re putting the needle. You need to move your hand and show where you’re putting it before you start
@steved11292 жыл бұрын
Sorry about that. Next time I need to replace the damping fluid I'll have to retake the video to make it more clear.
@chrisnelson20572 жыл бұрын
You should take shots from above..
@MAB_Audio_Nut Жыл бұрын
The right way to do it is to remove the piston . there are groves usually in the piston and those need to be filled with the fluid and than put back together. your method really doesn't get the fluid where it needs to go.
@TrueAudio11 ай бұрын
can you show us all the steps please. But this fellow's application certainly did some good, as you can see too
@arnoldtolker35052 жыл бұрын
Man sieht ja gar nichts, weil du die Hand davor hälts! Kommt das Silikon in das Rohr oder davor in den Spalt zwischen Rohr und Aufnahmehalterung?
@TrueAudio11 ай бұрын
Nobody knows
@TrueAudio11 ай бұрын
could you do this all over again please. you big hands made to video portion kinda useless so where did you add the fluid to? i don't have a clue after watching this 8 times now. could you do this all over again please, please, please.
@steved112911 ай бұрын
I'll be sure to remake it next time I have to do this on a turntable.