Removing an Extruder Blockage Bambu X1C

Рет қаралды 2,953

3 ай бұрын

This is the first time that I have needed to take the extruder apart (actually ended up doing it twice today with the same roll of filament). Even though I know it is simple to do, I was a little nervous about taking the extruder apart, so I wanted to show my process and let others know that it is super easy to do.

Пікірлер: 23

@jasonpowell6051 10 күн бұрын

Just encountered my very first extruder clog and your video got me solved in under 10 minutes. Thank you for this!

@Steve4948 10 күн бұрын

That’s great! I’m glad the video could help you.

@carolmatt2959 Ай бұрын

Great video, Steve…..so much better than most; thank you!

@Steve4948 23 күн бұрын

Thank you so much!

@Phantomnyx_ttv 25 күн бұрын

Thanks Steve, really saved me here 🙏 great video

@Steve4948 25 күн бұрын

Thank you so much! I’m glad the video helped.

@rickkubina8977 20 күн бұрын

Great instructions - thank you!

@Steve4948 19 күн бұрын

Glad it was helpful!

@MrBrettw15 Ай бұрын

Thank you!!!

@michaelpusateri1997 Ай бұрын

Great video, very helpful, thank you.

@Steve4948 Ай бұрын

Thank you, Glad it was helpful!

@PeterAgostiniJdcap26 4 күн бұрын

Thanks for the video . What brand of filament ?

@Steve4948 3 күн бұрын

I don’t recall the filament brand. Looking back at my order history, Polymaker would fit the timeline. However, I’ve used a lot of poly maker filament and haven’t had any issues with it. I’m not even 100% sure it was a filament issue but it happened two times in a row so I threw that roll out.

@PeterAgostiniJdcap26 3 күн бұрын

@@Steve4948 ok ty

@pieyrot 11 күн бұрын

Thanks Steve, that was much quicker with your video instead of figuring out myself 🙂 I have about the same issue. A melted piece of filament that was stuck in the extruder. It never happend to me before and I was wondering if you managed to figure out what was the reason of it? It happend to me when I was using a 0.2mm head and often changing color.

@Steve4948 11 күн бұрын

I am glad the video helped. I am assuming the problem was a bad roll of filament, although there is no way to prove it. It happened two times in a short time. I threw that roller filament away and have never had the problem again. I’ve only used the .2 mm a couple times and both times it worked fine.

@pieyrot 11 күн бұрын

Thanks. I'm not quite sure the filament id faulty ... although the filament may behave differently on a 0.2mm head. I never had an issue with this filament on a 0.4mm head... Anyway! Some thing you better not ask in IT world 😉 "that's how it is"! I'll keep on trying anyway ! Thanks for your video!

@mrgelvis 16 күн бұрын

Quick question, my issue is not with the extruder. In fact even bought a second one thinking it was. However, after swapping extruders it's still not printing in that no filament is coming out of the hot end? I didn't think a hot end could be clogged up as whatever filament being printed would just be melted and passed through? I did change the hot end nozzle with the replacement which came with the printer and managed to get 3 hours into the print before the second nozzle got jammed up. Is it possible there's an issue with the thermistor? Perhaps not heating up the hot end enough even though it reads as being 250? Any help would be appreciated.

@Steve4948 16 күн бұрын

I don’t know a whole lot about hot and issues, but did have to replace the complete hot and on my P1S at one point. I had the hot and on hand and just swapped it out without really doing any troubleshooting beyond that, but it fixed the issue. I would think it would be possible for a thermistor issue to cause the problem if the hot end is not getting hot enough. Sorry, I couldn’t be more help.

@musicalatv Ай бұрын

I feel like this is the 3D printer version of a kidney stone...

@sebastianalpaca4051 24 күн бұрын

Hello, I did exactly the same thing but when I put it back together and turned it on when it was moving it started making a noise like something was being grabbed, do you have any idea what it could be?

@Steve4948 23 күн бұрын

No, I’m not sure what inside the extruder would make noise. Sorry I can’t be of any help.

@Ash3DGuy Ай бұрын

Why cut off the part of taking the pcb off? Yours have no silicone holding the extruder connection which I have and I think I pulled the pcb connection off I was so gentle!