Love your video, thanks to your tutorial i was able to do it by myself and saved a lot of money
@asiba26 жыл бұрын
very good time consuming and informative
@blitziderdonnergott5 жыл бұрын
Danke hat super geklappt.👌👍
@arnoteerink6 жыл бұрын
Why remove the caliper ??? To change the brake disk...you only have to remove the 12 size bolts at the back (sadel). If you change only the brake pads...remove pin at the underside...than you flip the calliper up...and change pads... Pushing back pignon first...also verry easy this way... Easy as hell.
@BlackTalon534 жыл бұрын
It took me FOREVER to get the safety clip at 6:32 out. It wasnt a clip but some twisted bit of stainless steel wire. I had to get to get my Dremel with the miniature cutting wheel insert out into my driveway and cut it off, and then cut a slit into the end of the safety bolt so I could twist it in its hole with a screwdriver and pull out the remaining bit of the stainless steel wire from the backside of the bolt. It was a gigantic pain in the behind.
@LOREGUINNESS3 жыл бұрын
Thanks for sharing. What did you use After ?
@BlackTalon533 жыл бұрын
@@LOREGUINNESS I used one of the clips that hold the body shells of my RC cars on their chassis. They have to be slightly shortened first so you can push them in as far as ncessary, and they rust fast in the hole too though. I may try a couple of twisted together strands from a stainless Bowden cable next.
@BlackTalon533 жыл бұрын
@@LOREGUINNESS I used one of the clips that hold the body shells of my RC cars in place on their chassis. That works really well. They have to be shortened with a Dremel first too so they can be pushed sufficiently far in though, and they rust fast in the hole too. I may try some twisted together strands from a stainless steel Bowden cable next.
@LOREGUINNESS3 жыл бұрын
@@BlackTalon53 thanks. What do you think using a simple iron wire from the bobbin? A well knotted One.
@BlackTalon533 жыл бұрын
@@LOREGUINNESS I think it would rust in the hole too, and it might be too brittle and break. I have been thinking about cutting a groove in the extreme end of the pin and securing it with an E-clip. That way I wouldnt have to put anything in the hole at all.
@pauljones13502 жыл бұрын
This is great thankyou dosvedania,jacking point is further down ledge little arrow points to it,are there any brake retaining spring clips holding pads on 2013 panda pop 1.2 do you know anyone or just retaining pin like this
@pauljones13502 жыл бұрын
Spasibo za remoht
@hamishanderson86197 жыл бұрын
Great video Bud!! What did you do about the fault code though, or did it not come up?
@ConstantinLehadus7 жыл бұрын
I do not have error code
@MotoRoUsa7 жыл бұрын
Cam mult a durat domnul Cristian haha
@anselmfritsch57285 жыл бұрын
Constantin, did you forget to push the brake hose back into the holder? If yes, please do this, otherwise the hose will tear. Constantin, hast Du vergessen, den Bremsschlauch wieder einzuhängen? Falls ja, mache das doch noch, sonst besteht die Gefahr dass der Bremsschlauch kaputt geht.
@mister.c4631 Жыл бұрын
No jack stands? Ridiculous to do this held on a standard jack
@petruttiberiu69817 жыл бұрын
Si trebuia sa schimbi si garniturile la pistonas
@tygerbright1173 жыл бұрын
I don't think that is the jacking point!
@petruttiberiu69817 жыл бұрын
Trebuia sa le strângi mult mai bine.. si în loc sa dai cu acea vaselină mai bine dădeai cu o pasta autoblocanta ... -cu direcția si cu frânele nu te joci!-
@anselmfritsch57285 жыл бұрын
By the way: It is not the only error you make, but the worst one. Nebenbei: Das ist nicht der einzige Fehler den Du machst, aber der schlimmste.
@remusrms72523 жыл бұрын
Salut..ce dimensiune au discurile tale ?
@ConstantinLehadus3 жыл бұрын
Nu mai stiu am vandut masina dar era super tare fiatul
@jonj42225 жыл бұрын
Salut am si eu o Panda 1.1 2004,am schimbat si eu discurile si dupa o luna s-au ovalizat.Discurile au fost TRW placutele la fel.Ale tale au mers bine?Cu rugina ai probleme?
@ConstantinLehadus5 жыл бұрын
Salut referitor la discuri si placute nu am avut probleme cu ele, masina am vanduto la niste rude si sunt foarte multumiti
@SoloTravel.D6 жыл бұрын
Salut Ai idee cum pot face sa aprind faza scurta si proiectoarele cand inchid masina din cheie ?! Am o panda exact ca a ta :) Ms !!
@ConstantinLehadus6 жыл бұрын
Salut. nu ma pricep la partea electrica.
@SoloTravel.D6 жыл бұрын
Ahhh :(( Ms oricum de reply :) Ma batea gandul sa schimb si eu placutele dar mi.e frica de pistonul ala ca n.am cum sa.l fortez inapoi Oricum f okay tutorialul :)
@ConstantinLehadus6 жыл бұрын
eu am avut probleme pe spate cu cilindru frana cand l-am inlocuit sa rupt conducta pentru ca era corodata rau si nu sa mai desfacut