Replacing a bad tie rod end on 2006 Volvo V50, S40, C30, C70. P1 Platform

Рет қаралды 10,241

11 ай бұрын

2006 Volvo V50 T5 AWD with 65,000km / 40,000 miles.
Bad driver side outer tie rod end. Replacing both sides and performing alignment after fixes the knocking noise.
TRW - JTE1107 Left side Driver / Volvo 31201413
TRW - JTE 1106 Right side Passenger / Volvo 31201412
Thx to Minute Muffler Auto Service Centre for Alignment service. Well recommended
Address: 1011 Main St, Winnipeg, MB R2W 3P9

Пікірлер: 26

@mlivshiz 10 ай бұрын

I don’t have a V50, but I owned a 2012 XC70 for 5.5 years that I just sold. Throughout my ownership, anytime I needed to perform any maintenance or repair, the first thing I did was visit your channel. Thanks for the hours of extremely useful content. You saved me a lot of time, sir. Thank you.

@Colin623 Ай бұрын

Excellent video, very well filmed and you explained things so that anyone can understand, I have to replace both the inner and outer tie rods on my Volvo C70II 2011, so this video has been helpful.

@martij30 11 ай бұрын

Thanks for filming these repairs. They're useful to watch, even when working on a car that's not the exact same model.

@phitanvo4767 8 ай бұрын

I have installed those TRW for my S40 in spring 2023 and purchased from FCP Euro. They are working great for such cheap price and guaranteed for life!

@Pesar25 11 ай бұрын

It is great you do all the repairs yourself. If you would go to a dealer these kind of relatively simple repairs would indeed cost a lot.

@volvosweden 11 ай бұрын

100%

@sandhusbythesea1122 11 ай бұрын

Great video Not even dealer another shops as well charge 700$

@adisl6659 10 ай бұрын

@@sandhusbythesea1122 My diesel filter has gone really really bad, i changed it for the first time, i needed to pump it by my self... i was curious and i called Volvo dealer garage. These thiefs asked me 320€.. i did it by my self for 42€- 25min of work. Filter cost me 22€ and handpump 20€

@danielfernandez1129 11 ай бұрын

I love all your vids have helped me so much with my 2011 s80 T6 . Thank you !!

@volvosweden 11 ай бұрын

Thx!

@UB4PMC 11 ай бұрын

Т6 супер мотор мой любимый которых уже нет и не будет

@pg41226 11 ай бұрын

You’ve nicely torqued the nuts with a torque wrench… and the garage guys just did it with an airgun again 😂👍🏼

@volvosweden 11 ай бұрын

Wanna do it right? Do it yourself

@allatkalich2576 11 ай бұрын

well done!

@alexolender1131 11 ай бұрын

👍

@husseinelaghil9440 11 ай бұрын

Plz video for how to clean VVT sensors at S60/XC60 2011-2013

@itsallminor6133 10 ай бұрын

It may soon be the end of my 08 xc70😢😢. Despite undercoating, rust underneath. Small hole in quarter under neath under the edge of the plastic molding. Right underneath in front of rear tire behind the plastic molding. Rest of the underneath has a bit of rust too, but more so toward the back. Deciding what to do. Its at a 160k miles running great. 😢😢😢😢

@zmanvideo1 11 ай бұрын

can I ask what type/brand of torque wrench you used? thanks

@volvosweden 11 ай бұрын

www.princessauto.com/en/3-8-in-dr-click-type-torque-wrench/product/PA0002920935

@danielberca5997 11 ай бұрын

400 dollars? That is insane, i love Europe, this would have been 100 $ for both trw parts

@volvosweden 11 ай бұрын

Well it was less. 130$ for both tie rods and 180$ for alignment. All Canadian dollar.

@martij30 11 ай бұрын

@@volvosweden That must be a very good alignment, almost double the price of what I usually pay. Then again, in Europe these parts are probably more easily accessible than in Canada. A set of the TRW tie rod ends costs 45 EUR, that's about 65 CAD.