Replacing drive belt/fan belt/serpentine belt on Nissan Micra after hearing squelching noise coming from the belt when accelerating
Пікірлер: 20
@readychalk51456 ай бұрын
Great content! I need to replace a water pump but watching this has helped me understand how to even get to the bloody thing haha
@simonbone9 ай бұрын
I replaced my Micra's belt by reaching down with the hood open. It was a bit fiddly, but there was no need to remove the wheel or the panels to get to it. There is just enough clearance to do so.
@micradocs9 ай бұрын
Yes, there are a few different ways to get to it. This method I uploaded I thought was ideal for those needing more room to manoeuvre :)
@simonbone6 ай бұрын
@@micradocs It's a few months later and I now have had to replace the water pump, and while I was at it I changed the tensioner pulley too. I'm now regretting trying to do all this from the top. The tensioner in particular is a real pain because you can't see what you are doing, and it is possible to install it wrong. (Edit:) Ultimately, what I did was to remove the tensioner screw mechanism, unscrew it to the loosest position, then put it back in the correct position and reinstall the pulley on the other side. That way there was plenty of slack for the belt to go on, while I could be sure that the tensioner screw thingie hadn't slipped out of its correct position. But yeah, in all the time it took it probably would have been somewhat easier to go at it from the side!
@hassan.ali10116 күн бұрын
Hello friend. Would you mind elaborating on how you did this? I am looking to do it the same way you did. Did you remove any parts out the way to get there? Is there any tutorial u followed or anything ?
@simonbone16 күн бұрын
@@hassan.ali101 Assuming you have the same engine (1.2 3-cylinder), it wasn't hard. Once you figure out how to loosen and tighten the tensioner, the belt comes off easily from the top, and the pulley and water pump come off and go on relatively easily. If your new water pump hasa a paper gasket (like SEK) be sure to get it wet so it sticks in place, because you won't be able to see everything you are doing.
@erkkihamalainen57258 ай бұрын
New belt, did few days noise after start, then settles and now quiet as normal. 2006 1.2 ac, replaced in 218 tkm, old belt looked not so worn only a bit. New belt is Gates, old maybe original.
@elvinismailov59488 ай бұрын
Hello my friend how much you need to tighten the bolt tensioner?
@danc16605 ай бұрын
How did you gauge the correct tension for the belt?
@micradocs5 ай бұрын
Ideally you should use a torque wrench, but I usually go by feel of the belt, should be nice and tight
@mondragon1313x6 ай бұрын
¿En el Micra K13 sería igual?
@micradocs6 ай бұрын
Si, es igual
@matthayes85243 күн бұрын
Is the bolt on the tensioner reverse threaded by any chance?
@micradocs3 күн бұрын
@@matthayes8524 the main bolt that holds the tensioner on is turned anti-clockwise to loosen it, there is another bolt on side also. I have another video on my channel where I replaced the tensioner altogether and I gave a brief explainer. Have a watch it may help
@matthayes85242 күн бұрын
@micradocs thanks, I just need to give it some Wd40 and a bigger tool to get it off then
@Rabi_Burud10 ай бұрын
Belt size?
@micradocs10 ай бұрын
1165mm it's slightly longer because it this vehicle has AC.
@erkkihamalainen57258 ай бұрын
1170 mm also at market, will do CR12DE engine with ac
@Rabi_Burud8 ай бұрын
@@erkkihamalainen5725 bro i have nissan sunny 2015 model diesel. My both bulb high beam is not working any solution? I changed the bulbs and combination switch as well