Replacing the Exhaust Donuts for your car or truck!

No video

Replacing the Exhaust Donuts for your car or truck!

Рет қаралды 89,326

Күн бұрын

This video shows how to replace the exhaust gaskets/donut on your exhaust system. This video will NOT show how to replace the exhaust manifold gasket. Thanks for watching!

Пікірлер: 40

@RemmikRotus 2 жыл бұрын

Thanks for the concise video. It’s been decades since I replaced a donut gasket and just wanted to see what I was getting into on my friends 2001 Expedition. It took my 4 tries with other videos that either tried to hard to be “entertaining” or were so off topic most of the video, I could not get through any of them to even get a brief overview.

@TheDadBodWorkshop 2 жыл бұрын

I'm glad you found it helpful! Good luck with your projects!

@leefinstad4272 Жыл бұрын

Thank you so much for putting videos like this up, saved me from putting a lot of coins in the swear jar!

@TheDadBodWorkshop Жыл бұрын

Thanks for the kind reply. So glad this was helpful!

@mariarappana 2 ай бұрын

Thanks! Just the video I was looking for!

@richardburdette4730 Жыл бұрын

Ratchet strap is a great idea that I never thought to do even once lol

@TheDadBodWorkshop Жыл бұрын

Thank you! Good luck with your projects!

@joshuazirkle4616 6 ай бұрын

Thanks first time I learned about it even having gaskets. I'm replacing the flange gasket on my 05 f150 4.6 xl . I didn't know which way it goes because the stock cats didn't have any to begin with. Thanks a bunch

@markellrobinson4447 5 ай бұрын

Great video helps a lot

@i_am_wi11_ Жыл бұрын

Good and straight forward

@TheDadBodWorkshop Жыл бұрын

Thank you!

@TimJackson-x2n Ай бұрын

Thanks for this information.

@thereaper2762 25 күн бұрын

Great vid! All I've been able to find is complete manifold swaps but I think the little donut seal is my real issue. Just wanted to know how much wiggle room I'd have or if I needed to keep going down the pipe unbolting everything. Would you or anyone recommend any type of paste or gasket material to help seal up and prevent failures?

@aubreyholmes1235 2 ай бұрын

Nicely done

@eltonyancey6426 4 ай бұрын

Great video. thanks a bunch.

@MonsterNinjaz Жыл бұрын

Doing this exact same job right now and used the exact same pick to get the ring out 😂😂

@TheDadBodWorkshop Жыл бұрын

Then you and I are both value shoppers! Thanks for supporting the channel!

@dustinbingman382 5 ай бұрын

Is the driver side (thinner one) directional?

@ksfarms6235 Жыл бұрын

Thanks for the video

@w.c.6678 3 ай бұрын

Good vid bro.

@travishull6503 Жыл бұрын

Is this on a 2015-2019 gmc Sierra 2500hd 6.0? @TheDadBodWorkshop

@johnsmith-qm1mr 2 жыл бұрын

Did you take the front wheels off for more access?

@TheDadBodWorkshop 2 жыл бұрын

I did not. I had plenty of access all from the underneath

@gcode3653 Жыл бұрын

Thank you

@Squiggly.Noodle 5 ай бұрын

0:08 Before 5:30 After

@travisroush2191 Жыл бұрын

Where do I buy these, just any part store?

@TheDadBodWorkshop Жыл бұрын

I try to buy most my parts from RockAuto if I have time to wait for them in the mail. Otherwise, I go to a local auto parts store or even Amazon if needed. Thanks for watching!

@BiteTheCurbNow Жыл бұрын

Thx

@colyntenny3592 2 жыл бұрын

I have a 1994 Chevy Silverado and wanted to know will I need 2 different gaskets to change both like in the video or will 1 size fit both sides?

@TheDadBodWorkshop 2 жыл бұрын

I believe you will also need two different sizes. Thanks for watching!

@obs_vell439 Жыл бұрын

Sure you probably changed it by now but they are the same. I have 88.

@markrodgers1965 2 жыл бұрын

If it leaks after a new gasket, what could be the issue ?

@TheDadBodWorkshop 2 жыл бұрын

It's likely leaking at the manifold then. Either that or you have a small hole somewhere in the piping. Thanks for watching!

@ryanrobbins1469 2 жыл бұрын

Take a shopvak and blow air in to your tail pipe and spray soapy water on your exhaust

@TheDadBodWorkshop 2 жыл бұрын

@@ryanrobbins1469 That's a great suggestions. I may try this in the future, thanks!

@kevinconnor6921 11 ай бұрын

Neversieze the threads

@dottlenoodle9052 Жыл бұрын

Mine don't come off I tried 3 different guns😭

@rasmadrak Жыл бұрын

I had to tiger saw off a few of my bolts... If you have a torch, that might help to break them loose.

@wally7856 8 ай бұрын

MAP gas torch. Get the torch with the hose so you can maneuver it better. Heat the nut until it glows red, it'll take a couple minutes then quickly get your impact or a breaker bar on there. Use a 6 sided impact rated deep socket so you don't strip the threads. It'll come off once you get it glowing a dull red with the torch.

@kevinconnor6921 11 ай бұрын

Look like nuts