The editing of this video is indescribable.

Bravo! This video accurately depicts what it feels like when you inhale too much engine exhaust. Genius!

Great video and thanks for taking the extra time to show how to carefully take off the existing rusty bolts so not to break them!

it was a good enough video, but the looping was making my brain glitch

Great work and outstanding vocabulary, Sir! Looking forward to taking a stab at this project. Thanks for the excellent instructions.

im waaaayy to high for that loop....

THANK YOU SO MUCH! THIS HELPED - AND I SAVED A LOT OF MONEY!

Warning......do not watch this stoned....your head will explode.

Did I just have a stroke

very clear and informative- thanks!

Those are the easiest exhaust bolts ive ever seen to come off lol

Thanks you I will tackling this on my mitsubishi outlander on the weekend was vary informative.

More often than not, the section that the donut slides over would be badly pitted from corrosion. In many forums people recommend Ultra-Copper RTV. Though it is labeled as being oxygen-sensor safe, I'm wondering if a safer and more reliable solution would be to filling out the pitting with high temperature steel-epoxy then sanding it down. Some swear by Versachem Crack Sealer, which is ceramic based, for this task.

Do you absolutely need power tools for this or can I break the gasket off without an air hammer and loosen the bolts without a powered driver?

Great video, just what I needed!

I discovered my squeaking noise coming from underneath is at this point. Sprayed some silicone grease on it and it went away. But returned days later since the heat from the exhaust pipe would dry that up of course. I've checked and the bolts are as tight as you can get them. Although I'm not hearing any exhaust leaks. Would replacing the exhaust ring solve the problem anyway?

I learned alot. And keep in mind, don't leave excessive lube on your nuts. Your tool cold slip off. Lol.

great video, for me you missed a real important part though, the foot pounds on the bolts...?will it vary by car and location? my guess would be 30-40 ft.ib

Thanks for the great advice.

Thank you this was helpful.

Thanks for explaining why a spring bolt should be used.

Was this an outtake from the movie "Ground Hog Day"?

informative video, this one is the only one i found that shows how to remove the old gasket from the pipe. Thank you

God forbid the factory would use stainless hardware in this high corrosion environment.

Very helpful video, thank you!

Great video. I like the amount of detail that you provide. I have an exhaust leak for my 2015 chevy silverado. Do you have any pointers or advice that I would find helpful or useful before I get underneath there?

what's with the looping?

Hi, i had it on my montero and figure it out its getting a noise when the engine got to aircon in full. Is it with Bolt Spring not enough to that make noise?

excelent work, very good teaching

Somebody give Bob a 🍻 (beer)! 👍🏾

This is excellent content. Very helpful. Well done.

Great instructional video. Thank you, I almost paid $50 for some one to to replace it. I just bought the donut gasket for $24 and did it myself

Thanks for the info... its almost like i'd seen some of this before :)

Amused. I’ve literally heard the word “nut” more times in this video than I have in the last month alone. Lemme tell you. That’s an achievement.

Excellent for DIYers. Ignore the comments from shops who want to charge you for an entire new exhaust system when all you need is a simple gasket.

Thank You Sir, for all Information Exelent job

You should wipe that oil off. You don't want the tool...to slip on the nut. Thanks - Lumpy

I've got some high temp gasket maker. Could I use that instead of silicone?

Does the heat help remove the nut?

very, very good video. thnx

To add some clarity....as you didn't show it....the final installation should have the springs be NOT fully compressed...there should be a little air-space between each coil of the coil spring.

Am I crazy or is he saying stuff like 3 times

Thank you Rusty Joe.

if the flange is bad or loose will the engine sound louder?

I know how it goes now. Thank you Sir. ☺️

What infant did the film editing for this? Great video though, besides the loops and zooming✊🏾

What the spring bolt work ?

Great Content!

very good. thanks

do you have a video for Lexus rx350 front Y exhaust pipe gasket replacement?

Where do I get those spring bolts ?

any way to remove the donut sleeve bob?

I need to replace doughnut between the exhaust manifold to pipe.are those spring bolts I need?

It’s 2022! Do they make a bolt and nut that can handle the high heat and won’t rust

I have a Corolla with a rusty exhaust donut but isn't too loud. I've ordered a new exhaust donuts and bolts and will get changed next year. I think Japanese cars only use them.

Can I install the new gasket without requiring silicone or adhesive? Thanks.

I was really hoping at the very end they would show the beginning one more time...

To the point, thank you

That was trippy.

Is this car an Integra? I ask cause this is the job I gotta do. The pipe is down the center not split like a v8

First step is safety glasses whenever using pen oil and rust.

why in the world is it so difficult to find how much you are supposed to tighten the spring bolts? I'm. assuming bottoming them out is completely redundant

Feel like I'm watching the Groundhog Day movie.

soak them overnight with p.b. blaster or a oil covered rag! thanks for the vid!

Can you add somewhere in your videos what car you are working on

How much would it cost for a mechanic to replace front pipe gasket and bolts?(very rusty)

I went into a h3h3 trance watching this.

Is that what's known as exhaust manifold to pipe gasket?

You don't see that every day, really really lucky and the bolt and nut are not that rusted to start with !

perhaps use some anti-seize as well

How much cost to do this at exhaust shop if I supply the gaskets?

What size is the gasket

I think this is what I need for my 97 legacy outback, the spring bolts are completely rusted and I see no springs... the flange is wide open and It’s leaking. Everything is rusted and I think the donut deteriorated or something I don’t see that either lol it’s terrible

thanks bob

I NEED that wrench!!!

My bolts broke how can I get them out if they are rusted on there?

It’s like watching an episode of this old house.

My head felt like I was gltiching on the repeating lines LOL

Everything I have read,says don't use any type of silicone on the exhaust side of the system. It will ruin your convertor.

Did he use Hi-temp anti-seize? You should.

How does that usually cost

do it without a lift and in a parking lot

damn the heat resistant silicon thats the key, i cussed so much with mine moving and dropping out!! thanks

Deja vu

I have heard that silicone will poison the sensors.

there's a glitch in the Matrix

I've been working on my 74 f100 360 and I've worked on old cars/ trucks all my life and never had as much trouble as this one. Even smashed my finger almost off. Can't seem to get it on

i uh i feel like im being slapped around like a cat toy while watching this

Is this the remix?

No washers?

This only happens in the an alternate universe LOL!

This reminds me of a Neature Walk video.

What kind of penetrating oil is that!!

How tou do this on a 2014 grand cherokee?

Lucky you I didn't have a back bolt and snapped mynuts. I've got new nuts and bolts , Hope my girlfriend will enjoy the work

The spring on my bolts never compress all the way what am I doing wrong

Yeah sooo easy, any one could clearly torque on exhaust bolts like that and break the rust weld... I should just like my Granny change my exhaust if it's that easy.

Lol that was a funny spoof video

Great video...kinda felt like a porn director from the '70s shot the video...lol

would be more informative at different camera angles