One of the famous Thailand product amazing

Ballon test was great. The granddaughter thought it was funny when it popped!!😀😀😀😀😀

excellent 👍 my friend ❤️

I really enjoyed this video. You make reservation look so easy. This was the first refrigerator compressor I have seen restoration. Thank you for sharing I look forward to your next restoration.

Заебись реставрация! Разобрать, помыть, собрать и не работающий ранее компрессор вдруг обретает второе дыхание. Можно было не разбирать, просто покрасить и всё, результат был бы такой же ошеломительный.

You clean it and re assamble it, but didn't fix it. it has no compression at all

Alllahji

17:39 непонятно зачем было протыкать шарик? Не смогли дождаться пока шарик сам не лопнет? После реставрации компрессор не выдаёт нормальное давление и нет производительности?

Good job! Great engine to make a homemade airbrush compressor.

Я тебе каждый день смотрю

Impresionante mantenimiento......

Many years ago (80s) helping my father in his commercial refrigeration business, we did this type of repairs on air conditioner compressors, usually it was a damaged valve or a burned coil and had to be rewound again. The problem with these repairs is that they are bound to not last long due to all the debris that gets into the system during welding. After quite a few repairs we started recommending the customer to buy a new compressor when the failure within the compressor itself. This video made me go back in time. Thank you very much for this video.

mở đến đó thì mở luôn cả piston xem còn ổn ko luôn đi chứ bác

wow boom👏👏👏

Excelente trabajo, saludos desde Buenos Aires.

i wonder ,How you made compressor suck all the oil in..? Thanks

А откуда появилась наклейка к данными о компрессоре?

fatto bene anche se nel finale avrei usato un discchetto da finitura lamellare

Good job. Greetings from Brazil.

Вау новые видео на канале

Good ii boss 👍👍😊😍

Wasted 18.17 minutes of my life - sorry………

I think you forgot to add oil

8:30 Reference to the Microwave repair by Restoration Skills

Infelizmente, não temos tantos profissionais como você que deixam as coisas velhas como novas novamente.... Parabéns pelo seu trabalho!!!! Unfortunately, we don't have as many professionals as you who make old things like new again.... Congratulations on your work!!!!

'好手工

If is repaired the compressor must have 350 or 400 PSI of pressure for use it, I think that the pressure is not enough

بطل

Thằng này việt nam hả anh em?

Bom trabalho 👏👏

🙏☝️🙏☝️🙏☝️🙏☝️🙏☝️

Круто

The balloon should have blown up a lot quicker and exploded sooner. You must have a leak around the weld area. You should have ground on the edge, not cut into the side above the edge. Then the weld would be on the edge and have a stronger weld. There was no need to cut into the inside as it was clean, until you got metal cutting dust inside.

Anda memotong di titik yang salah

Solo hiso el video no le probó cuántas libras de presion subió

Actually, you did nothing to that compressor except removing rust and painting 😂 You didn't even change the seals 😢

11:30 Same reference just with a different material

Excelent

Bien fait, mais je vois bien qu'il ne soit pas bien bien fait ! Car je sais qu'il y'a des pertes dans le châssis au niveau de la chambre de compression 🧐🤏👁️😉

No se hace asi desde la abierta.

👍

It presses intermittently why not press continuously on the dye gun🤔

CFC gas.

Funny how he took the piston rod cap off twice. That unit was clean inside. Pobably would have worked just fine. The oil was even clean. Where`s the severe damage???

very weak pressure

Ese compresor está mal reparado se demoró demasiado en llenar ese globo de aire la mofla está mala

get a new one!

Fake kkkkkkkkkkkkkkkkkkkkkkkkkkkk

What a waste of time. Do you even own a pressure gauge or a micrometer?

pert de temps pour rien

fake