Restoring mower deck Cub Cadet

No video

Restoring mower deck Cub Cadet

Рет қаралды 44,420

Larssons Garage

Күн бұрын

Пікірлер: 33

@bigsonslawncare 2 ай бұрын

One of the best cutting decks in the market!

@vikingerik80 2 ай бұрын

Nice work and great detail! I did the underside of a JD LX255 and came out great with the brush and paint.

@thecargotsold 2 жыл бұрын

That is so fast, I wish I can do it too. 😊. Thanks for a great video

@johnbravo8994 3 ай бұрын

Looks good........from a distance

@gearhead366 Жыл бұрын

Paint brush... why didn't I consider that? No fumes (well... almost none), and less waste. I have a CC fabricated deck. The mower needed work. I got it running, but haven't been able to spend any time on the deck. Sounds like a good winter project. BTW, this belongs in the "Oddly satisfying" Reddit sub.

@ramonkjhjjkjkkiy6541 3 ай бұрын

Nice job 👍

@Kevin_747 2 жыл бұрын

Nice work. I have a new to me Cub Cadet that needs this done. The big problem is grass stays trapped under the pulley guards allowing moisture to collect so I run with them off so I can blow compressed air across the deck and clean it off. I will disassemble and take it to a sandblaster, you worked harder than I want to.

@6548ww 10 ай бұрын

Got the same Deck on my Huskee Supreme 26hp 54" from Tractor Supply it's an MTD Deck they make them for many different brands in many sizes mine is an exact duplicate of this one but red instead of yellow

@danielpadgett2831 Жыл бұрын

Just wondering why you put the belt guards on without putting the belt on?

@TheCaperfish 6 ай бұрын

bro ergonomics , put it up on a couple of saw horses

@rayjrdibenedetto867 2 жыл бұрын

Good morning. I am working on a 38” john deere deck that i just picked up and was wondering why you brushed this deck instead of rattle cans? Im thinking of new spindles also because i don’t see a grease fitting? Thank you and have a good day

@Larssons-Garage 2 жыл бұрын

Good morning. I use brush to access everywhere and to get a thicker layer of paint. but to get a better finish, rattle cans is better. New spindles sounds like a good idea so you are sure it can be greased. but som deck dont have grease fittings. Thanks and have a good day

@rayjrdibenedetto867 2 жыл бұрын

@@Larssons-Garage Good morning. Ok i was just wondering and have rattle cans in a bunch of cover but wanna take a wire brush to is first-i did see yesterday that there are grease fittings-maybe i will just replace the bearings- i have watched some videos on that and how to put a vent hole in the spindle and remove 1 side of the bearing cover and face them inwards so they get grease! Kinda makes a lot of sense! Thank you and have a good day

@setdown2 2 жыл бұрын

@@rayjrdibenedetto867 I would just replace or repack the bearings…imho…😊

@rayjrdibenedetto867 2 жыл бұрын

@@setdown2 Hi. Looked again at this deck and do see a grease fitting on each spindle. They don’t wobble so thinking of replacing the bearings. Thank you for your help. Hope you have a good day

@earthjammer 2 жыл бұрын

Nice job.

@johnrojas4282 3 ай бұрын

What kind paint you used?

@earlpowers4157 2 жыл бұрын

What was first coat ? Paint?

@Larssons-Garage 2 жыл бұрын

Hi! Rust converter

@GT_Racer347 Жыл бұрын

Sweet 👍🏻 👍🏻

@stigbjerkan4651 2 жыл бұрын

Brukte du Rust Master som grunning? Smart! Da trenger jeg ikke sandblåse. :)

@Larssons-Garage 2 жыл бұрын

Precis👍 Det funkade för mig :)

@alloutofdonuts3998 2 жыл бұрын

I just did mine last summer, same looking deck except mine’s a 50”. Not even 3 mows in this year and the paint started flaking off exposing rust underneath. What a PITA it was the first time, and I used rattle cans but I didn’t convert/treat the rust. Not that it’ll fix it forever but it slows down the rust. So I stripped it all back down to bare metal and put a rust reformer paint on it(w/spray gun) this time, then sprayed some really thick paint on it. Waiting on a few more parts to put it back together. Seriously wish I’d bought a mower w/fabricated deck as that’d actually be worth repairing. Best case scenario, this deck will be flaking off in 2-3 years again. Anyone know of a good clear spray or coating that’ll help keep the grass and dirt from sticking so bad?

@johnsmith6368 2 жыл бұрын

You invent something that works to keep the grass and dirt from sticking and you will become a very rich person in no time.

@Zekerose Жыл бұрын

Slip plate

@earlpowers4157 2 жыл бұрын

What kind of paint for first & Second coat?

@Larssons-Garage 2 жыл бұрын

First Rust converter / sealer , then Cub Cadet yellow